Spectra Precision HV302 Manuel utilisateur
HV302 Hands-on Training
January 2015
HV302 Controls
Battery Status LED
Level-LED
Manual/Single Slope Mode/
Standby Button
Power Button
HI-/Manual-
Standby - LED
Slope/Alignment
Buttons
Rotation Button
Scan Button Scan Button Rotation Button
RC402N Radio Remote Control
Left & Right
Buttons
Menu button
Up & Down Buttons
LCD - Display
On/Off Button
RC402N-Battery status LED
Enter button
Hand loop
Manual/Single Slope Mode/
Standby Button
HV302 Peripherals
Rubber Feet
Serial Number
5/8” x 11
Beam Exit
Metal Sunshade Sighting Guides
Rotor Vial
HV302 Peripherals
Plastic Feet
Rubber Foot Laser Safety Labels
5/8” x 11
Installing The Batteries
Enter the battery housing, by
turning the battery-door knob
counterclockwise
Install/remove the rechargeable
battery Pack. It is keyed to
prevent miss-insertion. The cage
prevents accidental charging of
Alkaline batteries
Do not try to open the cage for
exchanging the rechargeable
batteries
Worldwide charger has plugs for
US, EU, AU and GB
Recharge time is about 10 hours
Installing The Batteries
If using 4 x D-cell Alkaline's, note the
plus (+) and minus(-) diagram on the
battery door. Do NOT try to install
Alkaline batteries in the rechargeable
battery Pack!
Special screws are used to ensure only
autorized service centers can replace the
batteries. Trying to open the cage will
destroy the cage lid holders.
New warning label
at the battery cage
Special Features using the optional RC402N
M-Button : Quickly press and release
starts the MENU entry and can be used
to return to the previous menu position
E-Button : Quickly press and release
starts the selected mode
Manual Button : Quickly press and
release activates/deactivates the manual
mode/ single slope mode; press and
hold for 3 seconds activates/deactivates
the Standby mode
Up/Down Arrow Buttons
Left/Right Arrow Buttons
ON/OFF button - press for 1 second
to turn on the unit; press and hold for 2
seconds to turn off the unit
RC402N Battery- Status-LED (red)
Battery status laser
Mask mode indication
HI-Alert activated
The remote control mirrors the basic functionality of the HV302 keypad and
offers additional features.
Using the optional Radio Remote Control
Powering the RC402N
1. Open the battery door using a coin
or similar pry device to release the
battery door tab on the RC402N.
2. Insert two AA batteries noting the
plus (+) and minus (-) diagrams
inside the battery housing.
3. Close the battery door. Push down
until it “clicks” into the locked
position.
Turning On/Off the Radio Remote Control
Press the button to turn on the radio remote control.
To turn off the radio remote control, press and hold
the button for 2 seconds.
Display at RC402N
HV302 –horizontal setup Display at RC402N
HV302 - vertical setup
Pairing the remote control with the transmitter
First, make sure the transmitter and the
remote control are turned off. Then press
and hold the button and turn on the
transmitter.
–The battery LED flashes fast.
During the next 6 seconds repeat the
same steps on the remote control.
The Laser’s red battery LED flashes fast
and the remote’s display shows Pairing
OK for one second and then the same
function as the laser is actually working to
indicate the transmitter has been matched
with the remote control.
Autres manuels pour HV302
2
Table des matières
Autres manuels Spectra Precision Niveau laser
Spectra Precision
Spectra Precision AL28M Manuel utilisateur
Spectra Precision
Spectra Precision 1452GC Manuel utilisateur
Spectra Precision
Spectra Precision GL412N Manuel utilisateur
Spectra Precision
Spectra Precision LL100N Instructions de montage
Spectra Precision
Spectra Precision DET-2 Manuel utilisateur
Spectra Precision
Spectra Precision LL300 Manuel utilisateur
Spectra Precision
Spectra Precision LL300S Manuel d'instructions
Spectra Precision
Spectra Precision LL300S Guide d'installation
Spectra Precision
Spectra Precision LL300S Manuel utilisateur
Spectra Precision
Spectra Precision Trimble UL 633N Manuel utilisateur
