Speco VLD9 Manuel utilisateur

USER MANUAL

Thank you for purchasing our product. Speco Technologies is constantly developing and

improving products. We reserve the right to modify product design and specifications

without notice and without incurring any obligation.

VLD9 /VLD9M

Warnings

■ If the product does not work properly, please contact the dealer or where the product was purchased.

Speco Technologies is not responsible for any problems caused by improper operation or repair.

■ Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity

during transportation, storage, and/or installation.

■ Do not install near sources of heat.

■ Only install the product in environments inside the specification operating temperature and humidity

range.

■ Do not install the camera near power lines, radar equipment or other electromagnetic radiation.

■ Do not block any ventilation openings if any.

■ Use all the weatherproofing hardware requirement to minimize weather intrusion.

This camera series is the latest technology and advanced circuit design, which features high definition and

sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable,

ensuring the requirement of the HD monitoring in the traditional surveillance system.

Introduction

● High Resolution

Adopt high performance sensor, providing high definition and clear image.

● High Transmission Performance

Real-time transmission with high speed and long distance.

● DNR

Reduce noise from brightness and color signal.

● OSD

Access the camera settings which can be clearly displayed through the main menu.

● White Balance

Adjust the color temperature according to the environment automatically.

● AGC

Adjust the gain of amplifier, enabling the camera to output the standard video signal in different

lighting condition.

● Backlight Compensation (BLC)

When the back of the captured object is too much bright, you can set BLC for the captured object to

make it clearer.

● Backlight Compensation (BLC)

When the back of the captured object is too much bright, you can set BLC for the captured object to

make it clearer.

Cables

Power Cable

Video Output

Video Switch Cable

Video Switch: Four video output modes can be optional--AHD, TVI, CVI and CVBS

(a) remove the cover of the video switch cable; (b) hold and press the button in the video

switch cable for 5 seconds to switch the current video output.

Before you start, please make sure that the wall or ceiling is strong enough to wi ths tand three times

the weight of the camera. Please install and use the camera in the dry environment.

You’d better install back the lens cover or lower dome less than 4 hours after removing it.

The mounting types of cameras are only for reference.

Installation

►Mounting for VLD9

1. Drill the screw holes and the cable hole on the wall according to the drill template.

74.3

(mm)

2. Align the gap of the trim ring with the microphone by turning the trim ring with fingers. Then remove

the trim ring from the gap of the camera.

Rubber plug

Lower dome

* Install it when routing the

cables through the ceiling.

3. Loosen the screws to open the lower dome. Then route and connect the cables.

4. Secure the camera to the wall with screws provided as shown below.

5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then

adjust the camera according to the figure below to get an optimum angle.

Rotation 0°~355°

Pan 0°~355°

Tilt 0°~67°

6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower

dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.

Trim ring



Gap

Microphone

∅4.6

90.2mm

►Mounting for VLD9M

1. Drill the screw holes and the cable hole on the wall according to the drill template.

2. Align the gap of the trim ring with the microphone by turning the trim ring with fingers. Then remove

the trim ring from the gap of the camera.

Rubber plug

Lower dome

* Install it when routing the

cables through the ceiling.

3. Loosen the screws to open the lower dome. Then route and connect the cables.

4. Secure the camera to the wall with screws provided as shown below.

Gap

Trim Ring

Microphone

6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower

dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.

Turn

Rotation 0°~345°

Tilt 0°~77°

Pan 0°~345°

5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then

adjust the camera according to the figure below to get an optimum angle.

Specifications

Camera

Image Sensor

Resolution

Image size

Video Output

Image System

Electronic Shutter

IR Range (feet)

Frame Rate

Min. Illumination

Lens

Lens Mount

S/N Ratio

Ingress Protection

Functions

Function Control

Day & Night

WDR

Digital NR

AGC

Auto White Balance

HLC

BLC

LSC

Mirror

Privacy Mask

Smart IR

Sharpness

Image Setting

Defect Correction

Others

Power Supply

1/2.8" CMOS

2MP

1920×1080

AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI)

PAL/NTSC

33~66 65~98

30fps(60Hz); 25fps(50Hz)

0.001lux @F1.2, AGC ON; 0 lux with IR

2.8 mm 2.8~12 mm，motorized

M12 D14

≥ 52dB(AGC OFF)

IP 67 & IK10

OSD (UTC control)

ICR

120dB

Yes

Auto

DC12V (± 10%)

IR OFF: < 1W; IR OFF: < 1W;

Specifications

Models VLD9

Power Consumption

Dimensions (inch)

Working Environment

IR ON : < 4W IR ON : < 6W

-22 °F ~ 122 °F, 10 % ~ 90 %(relative humidity)

Ф5.61 3.95×

Ф4.72 3.45×

VLD9M

Model: VLD9 /VLD9M

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesired operation.

FCC Responsible Party:

Speco Technologies

200 New Highway

Amityville, NY 11701

www.specotech.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Speco Caméra de sécurité

Speco

Speco O4VB2 Manuel utilisateur

Speco

Speco HT61iLHB Manuel utilisateur

Speco

Speco VIP2D1M Manuel utilisateur

Speco

Speco CCLR13D1G Manuel utilisateur

Speco

Speco HT-INTB1 Manuel utilisateur

Speco

Speco O8FD1 Manuel utilisateur

Speco

Speco H2AB2 Manuel utilisateur

Speco

Speco HTD8FFI Manuel utilisateur

Speco

Speco Focus Free Intensifier HT7248FFiL Manuel utilisateur

Speco

Speco HTMD1H Manuel utilisateur

Speco

Speco HLPR1TW Manuel utilisateur

Speco

Speco COLOR CAMERA WDRT6 Manuel utilisateur

Speco

Speco ProVideo CVC-646HR Manuel utilisateur

Speco

Speco O4iT2W Manuel utilisateur

Speco

Speco WDR700VF Manuel utilisateur

Speco

Speco O2P25X Manuel utilisateur

Speco

Speco HT-7248FFI Manuel utilisateur

Speco

Speco VLED24T3W Series Manuel utilisateur

Speco

Speco O6MDP3N Manuel utilisateur

Speco

Speco CVC-652HZ Manuel utilisateur

Speco

Speco O4iT2W Manuel utilisateur

Speco

Speco VLB5 Manuel utilisateur

Speco

Speco CVC-225ES Manuel utilisateur

Speco

Speco VL-INTT5 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur