Spear & Jackson TA-COMP70 Manuel utilisateur

Instruction Manual

2.5HP 50 Litre

Belt Drive

Air Compressor

Introduction 3

Environmental Responsibilities 3

General Safety Instructions 3

Electrical Safety 4

Use of Extension Cords 4

Additional Safety Instructions 4-5

The Compressor & Its Components 5

Assembly & Operating Instructions 6

Automatic On/Off Switch 7

Overload Protection / Reset Procedure 7

Pressure Gauges 8

Pressure Regulator 8

Safety Valve 8

Compressor Set-Up 8

Shutting Down Your Compressor 9

Maintenance 9

Trouble Shooting 9

Exploded Diagram 10

Parts Listing 10

Supplier Contact Details 11

Warranty Details 12-13

Index

Introduction.

Project Air Compressors have been manufactured under stringent Quality Standards to meet the

performance criteria set by Spear & Jackson.

After familiarization you will find this compressor both easy and safe to operate.

Read the instruction manual completely before using your new Spear &Jackson Air

Compressor.

These compressors have many features which will make your work faster and easier.

Please ensure all waste and unwanted products and are disposed of in a safe and

environmentally friendly manner.

Environmental Responsibilities.

When using this product, basic safety precautions should always be followed:

DO NOT OPERATE A COMPRESSOR WHEN UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.

1. Read all instructions prior to using the product.

2. To reduce the risk of injury, close supervision is necessary when the compressor is in use

near children or infirm persons.

3. Know how to stop the compressor and be able to reduce the pressure immediately.

4. Be completely familiar with all the controls.

5. Please secure or cover any long hair, clothing or jewelry prior to using this compressor.

6. Do not reach over machines with moving parts when in operation.

7. Please ensure that any potential trip or slip hazard is removed prior to operating this

compressor.

8. Do not use the compressor if the power cord shows any signs of damage or wear. Repair or

replace the damaged cord before use.

9. Do not pull forcefully on the cord to disconnect it from the power point.

10. Keep the cord away from heat sources, oil and sharp edges.

11. NEVER move the unit by pulling on the air hose. Use the handle provided at the front and on

the rear of the tank.

12. Please ensure that the work area is well lit, ventilated and clean and tidy.

General Safety Instructions

Warning !

To reduce the risk of electrocution keep all connections dry and off the ground. Do not use if wet or in a

wet environment.

This product should only ever be connected to a properly manufactured, fitted and earthed power

outlet that complies with National and regional electrical authority regulations and requirements.

Extension cables or generators are not to be used with this product, as it may cause damage to

the Compressor. Such actions will void the warranty. Please use a longer Air Hose.

Electrical Safety Instructions

Additional Safety Instructions

1. Always wear ear and eye protection when using any compressor, air tool or power tool, or

are in the vicinity of the product when it is use.

2. Do not use the compressor in areas near combustible materials, combustible fumes or dust.

3. Always use a respirator or mask when spray painting or whenever there is a possibility

vapors may be inhaled.

4. DO NOT ALLOW CHILDREN TO OPERATE THE COMPRESSOR AT ANY TIME.

5. DO NOT MAKE ANY MODIFICATIONS OR ADJUSTMENTS TO THE UNIT OR ANY OF ITS

COMPONENTS.

7. UNITS WITH BROKEN OR MISSING PARTS OR WITHOUT THE PROTECTIVE HOUSING

OR COVERS SHOULD NEVER BE OPERATED.

8. Do not leave the compressor unattended while the pressure switch is in the “I” (on)

position.

9. Do not add or change oil while the compressor is in operation.

10. Use only the supplied or recommended lubricating oil for the compressor. Spear & Jackson

Compressor Oil is available from Bunnings Stores (Product Code CA-CAP721-04).

Recommended viscosity ISO 0046.

11. This compressor is fitted with a pressure activated “On/Off” switch. When the switch is in the

“on” position, the compressor may start operating at any time when the pressure in the tank

falls below the preset level of the pressure switch.

12. When not in use, we recommend that all tools and hoses be disconnected and the tanks

drained of air and moisture. We also recommend that you leave the tank drain open when

the compressor is not in use.

13.To reduce the risk of fire or explosion, never spray flammable liquids in a confined area.

14.Do not ever directly inhale compressed air. Serious injury could occur.

15.Do not use the air from the compressor for any re-breathing apparatus.

16.Never apply the outlet air of this compressor directly on to any part of a person’s body. Do not

attempt to block the air outlet with your finger or any part of your body. Severe injury may

occur.

17.Do not weld anything to the air tank of the compressor. This could result in tank failure and will

void the warranty.

18. Do not operate the compressor with the shield, cowling or cover removed.

19. Before transporting the compressor it is recommended that the tank be drained of pressurized

air.

20.Spear & Jackson Australia Pty Ltd will not be responsible for any damage or injury resulting

from cases of misuse or negligence.

21.Spear & Jackson Australia Pty Ltd will not be liable for any changes made to the compressor nor

for any damage resulting from such changes.

22. This air compressor is a duty cycle tool. It is not designed to run 100% of the time. If

it is run on a continuous basis this may result in overheating or activation of the

thermal cut out. This compressor should not run for more than 40 minutes in every

hour. Continual use will void the warranty

Additional Safety Instructions

Warning !

In the event that an air line is cut or broken, the air supply must be turned off at the

compressor.

The Compressor and Its Parts

Air Filter

Oil Fill Cap

Belt Safety

Guard

Electrical Reset

button

Handle

Pump

Motor

Wheels Wheels

Tank Drain

(underneath)

Pressure

Switch

Regulator

Air Outlet

Pressure Relief Valve

Assembly & Operating Instructions

2. The unit is supplied with oil already in the pump. Please add sufficient oil from the bottle

supplied until the marker in the sight glass is level with the red indicator line.

Additional oil can be purchased from Bunnings if required

(Spear & Jackson Compressor Oil CA-CAP721-04).

Sight Glass

Empty Sight Glass

Over full Sight Glass

Correct Level

8. Before connecting the compressor to the power outlet, check for broken components

and any damage to the power cord.

1. The compressor is supplied with wheels, axles and a handle. Please remove unit from the box

and check for any damage. Please attached the handle and the wheels using the hardware

provided.

9. Make sure the pressure switch is in the “O” or OFF position.

When Red lever is UP compressor is OFF

10. Plug the unit into a properly fitted and earthed power outlet.

11. Attach the desired tool to the end of the air hose.

12. Switch the compressor on by lifting the red knob on the top of the pressure switch.

When Red lever is DOWN compressor is ON

Automatic On / Off

The compressor is equipped with a pressure activated on/off switch. The compressor will only

run when the switch is in the “I” or ON position (as per previous page).

Once the tank has reached the maximum preset pressure (125 PSI), the pump will

automatically shut off.

The pump will automatically restart once the pressure in the tank drops below the minimum

preset pressure (100 PSI).

The maximum and minimum pressures are set at the factory. Any attempt by the

operator to change them will void the warranty of the product.

Overload Protection / Reset Procedure

1. Switch “On/Off” Switch to “Off” Position.

2. Disconnect compressor from Power source.

3. Press the reset button located on the electrical box on top of the motor.

(As shown below)

4. Reconnect to power source.

5. Re activate compressor using the “On/Off” Switch.

Reset switch located here

Possible causes of motor overload are as follows -

1. Inadequate power supply.

2. Use of extension leads.

3. Overheating.

4. Lack of lubricating oil.

5. Use outside the standard operating parameters for this compressor.

The Tank Pressure Gauge supplies the reading of the air pressure inside the tank.

Pressure Gauges

NOTE. If you do not allow the air to discharge whilst you are setting the regulator, the pressure

as indicated on the regulated outlet gauge will be incorrect.

This gauge ONLY indicates the correct pressure while air is being discharged from the

outlet.

This compressor is fitted with an Air Pressure Regulator. It allows regulation of the output air

pressure.

Some air tools require a higher operating pressure than others. Please refer to the air pressure

requirements of your tools for the proper settings for the regulator.

Pressure Regulator

The compressor is equipped with a safety valve that will engage when the pressure in the

tank exceeds the maximum pressure setting, releasing any excess built up.

DO NOT REMOVE OR ATTEMPT TO ADJUST THE SAFETY VALVE.

Safety Switch

Safety Valve

Compressor Set Up

When you have finished using your compressor, follow these steps:-

1. Close the air outlet taps.

2. Switch off the compressor.

3. Disconnect unit from power outlet (power point).

4. Disconnect tools and / or Accessories from the air hose.

5. Disconnect the Air Hose.

6. Locate the drain valve on the underside of the tank.

7. Open the drain valve to release remaining pressurized air from within the tank. Moisture build

up in the tank is normal with air compressors, so a small amount of water may come out

while draining. (Draining the tank is vital for the longevity and safety of your air

compressor).

8. Store the compressor in a cool, dry place.

Shutting Down Your Compressor

1. The tank will require accumulated moisture to be drained from it on a regular basis. It is

recommended that the tank be drained of moisture after every 5 Hours of use. The drain

valve is located on the underside of the tank.

2. Check Oil level before each use.

3. Wash air filter insert in a mild soapy solution after 50 hours use. Operation in extreme

conditions e.g., dust, paint residue etc, may require more frequent cleaning.

4. Check handle is attached properly prior to use.

6. Check power cord for signs of wear and tear before each use.

7. Never use caustic agents to clean any part of the compressor.

8. Remove dust and dirt regularly. Wipe down compressor with a damp rag. Do not use alcohol,

petrol or other cleaning agent as this presents a fire hazard.

Maintenance

Trouble Shooting