SPACEMAKER EL64 Manuel utilisateur

ASSEMBLY INSTRUCTIONS FOR

MODELS

EL64, EL65, EL66, EL67, EL69

EG64H-A, EG65H-A, EG66H-A, EG67H-A, EG69H-A

HE64, HE65, HE66, HE67, HE69 AL01

15-5710507 English/French 05/07

EASY TO INSTALL

Manufactured by Spacemaker Limited

CAUTION: Some parts have sharp edges. Care must be taken when handling

the various pieces to avoid a mishap. For safety sake, please read the safety

information provided in this manual before beginning construction. Wear

gloves when handling metal parts.

100%CANADIAN

AH02

CONTENTS

•Pre-construction instructions • Anchoring the frame

•Assembling the building • Parts List and order information

PROCEED WITH CONFIDENCE

It might look complicated when you first unpack your building…but it really isn’t. Simply follow the

illustrated instructions and your building will go up quickly and accurately.

ASSEMBLY INSTRUCTIONS

•Before beginning construction...check local building codes regarding footings, location

and other requirements. Study and understand the owner's manual.

•You will need assistance…you’ll find that another person will speed the job and make

assembly easier.

•Selecting your site…choose an area that’s firm and level yet allows drainage away from

site.

WARNING! … DO NOT ERECT YOUR BUILDING IN AREAS THAT ARE SUBJECTED TO

HIGH WINDS, OR ERECT ON A WINDY DAY. ANY BUILDING LEFT PARTIALLY CON-

STRUCTED MAY BE SERIOUSLY DAMAGED IF LEFT IN THIS STATE.

•Sort and separate all parts and hardware…checking with the Parts List on Page 4 and

the illustrations on Page 5…be sure you have all parts and know where they belong in the

building. Each part has been numbered or illustrated, the quantity required and its part

number noted.

Foundation Preparation

• Hammer and Nails

• Spade or Shovel

• Hand Saw / Power Saw

• Lumber and/or Concrete

Optional Time-Savers

• Wrench / Nut Driver

• Electric / Cordless Drill

• Square

• String (for squaring frame)

Required

• Utility Knife / Scissors

• Pliers

• Carpenter's Level

• Tape Measure

Required

• Eye Goggles

• No. 2 Phillips Screwdriver

(with Hardened Magnetic Tip)

• Work Gloves

• Step Ladders

BUILDING CARE

•Carefree maintenance – Your building has been designed to give you years of carefree

service. All parts have been precision engineered for a perfect fit. It is manufactured from

heavily galvanized steel with exterior parts pre-enameled on both sides at the steel mill.

•IMPORTANT – This building is designed to withstand normal wind loads when

installed according to instructions. Manufacturer cannot be held responsible for

any consequences due to buildings that are not installed per instructions or for

damage due to weather conditions or acts of God.

•Follow step-by-step instructions carefully…complete

each step before going onto the next one.

•Retain this manual after assembly is completed…it

contains a complete parts list.

L03

IMPORTANT

PERSONAL SAFETY DURING BUILDINGS CONSTRUCTION

Some of the building components may contain sharp edges prior to assembly. Wear protective

work gloves while handling these components. Wear eye protection when using any form of power

tool. Do not use household voltage power tools in a wet or damp environment. Household voltage

power tools must be monitored and controlled by a Ground Fault Interrupter or more commonly

called a G.F.I. Do not use any part of the building's frame as a means of personal support while

attaching components during assembly.

PREPARATION OF BUILDING SITE

This building must be constructed on a SOLID

BASE FOUNDATION. We recommend a

poured concrete pad or large size concrete

patio stone squares for a suitable floor and

base. Which ever you select…make sure your

foundation area is firm and level and will allow

drainage away from the site. Make your solid

base foundation at least 4” (100mm) larger than

your building. The manufacturer is not re-

sponsible for the choice and the construc-

tion of the foundation.

NOTE: For a concrete pad base, prepare a

level bed for a firm footing layer of crushed

stone. The concrete pad should then be poured

to a thickness of 4” (100mm) to 5” (125mm).

When completed, allow to dry thoroughly for at

least 48 hours.

YOUR BUILDING MUST BE

ANCHORED

Your building must be firmly anchored to your concrete

pad or large concrete patio stone squares…to help

protect against damage in high winds.

FURTHER ANCHORING INSTRUCTIONS

FOLLOW AFTER ALL WALL AND ROOF

PANELS HAVE BEEN INSTALLED.

MODEL "A" "A" "B" "B"

CM INCH CM INCH

6x4 172.7 68 114.9 45 1/4

6x5 172.7 68 146.1 57 1/2

6x6 172.7 68 177.2 69 3/4

6x7 172.7 68 208.3 82

6x9 172.7 68 270.5 106 1/2

OUTSIDE MEASUREMENTS OF BUILDING AT BASE

“B” + 100mm (4")

MINIMUM

“A” + 100mm (4")

MINIMUM

DOORWAY

Part Part Quantity

Number Description 6x4 6x5 6x6 6x7 6x9

64H Rear Base Rail 2 2 2 2 2

53H Side Base Rail - 2 - - 4

63H Side Base Rail - - 2 - -

73H Side Base Rail 2 - - 4 -

62H Front Base Rail 2 2 2 2 2

610H Entry Ramp 1 1 1 1 1

* Corner Panel 2 2 2 2 2

* Half Corner Panel (Front Only) 2 2 2 2 2

640H Rear Top Rail 2 2 2 2 2

527M Side Top Rail - 2 - - 4

627M Side Top Rail - - 2 - -

727M Side Top Rail 2 - - 4 -

66H Door Track 2 2 2 2 2

635H Door Fascia 1 1 1 1 1

69G DoorJamb 2 2 2 2 2

628H Front Midwall Brace 2 2 2 2 2

* Wall Panel 3 5 5 7 9

* Half Wall Panel 2 - 2 - -

640H Rear Midwall Brace 2 2 2 2 2

527M Side Midwall Brace - 2 - - 4

627M Side Midwall Brace - - 2 - -

727M Side Midwall Brace 2 - - 4 -

* Left Gable 2 2 2 2 2

* Right Gable 2 2 2 2 2

516L Main Ridge Beam - 2 - - -

616L Main Ridge Beam - - 2 - -

H716H Main Ridge Beam 2 - - 4 -

H516H Main Ridge Beam - - - - 4

618H Left Roof End Panel 2 2 2 2 2

644H Right Roof End Panel 2 2 2 2 2

* Roof Panel 2 4 4 6 8

* Half Roof Panel 2 - 2 - -

420H RidgeCover 1 - - - -

520H RidgeCover - 1 - - 1

620H RidgeCover - - 1 - -

720H RidgeCover - - - 2 -

920H RidgeCover - - - - 1

541H Roof Edge Trim - 2 - - 4

641H Roof Edge Trim - - 2 - -

741H Roof Edge Trim 2 - - 4 -

* Door Panel 2 2 2 2 2

DISO3 DoorStrengthener 4 4 4 4 4

623 Horizontal Door Brace 2 2 2 2 2

632 Top & Bottom Door Brace 4 4 4 4 4

* Weatherseal Tape 1 1 1 1 1

49H Ridge Cover End Cap 2 2 2 2 2

* DoorHandle 2 2 2 2 2

* Plastic Washer Tree 2 2 2 2 2

Owner'sManual 1 1 1 1 1

Hardware Kit Contains

(Bolts, Nuts and Screws)

* Roof Corner Cap 4 4 4 4 4

* Door Spacer (2 sets of 2) 4 4 4 4 4

A67 Door Glide 4 4 4 4 4

AL04

* Indicates that part number is NOT stamped in the part see illustrations.

Painted parts may contain a prefix that designates color / material.

Parts List

IMPORTANT...When ordering parts please provide number stamped on the surface of galvalized parts. In the case of wall

and roof panels please provide the model number of the building, color and size of panels.

To order parts please use order form on the last page.

Parts Not Identified with Part Number

L05

CORNER PANEL HALF CORNER PANEL WALL PANEL HALF WALL PANEL

LEFT GABLE RIGHT GABLE

ROOF PANEL HALF ROOF PANEL

ROOF CORNER

CAP

DOOR PANEL

WEATHERSEAL TAPE DOOR HANDLE PLASTIC WASHER TREE

ITEMS in the HARDWARE BAG

DOOR SPACER DOOR GLIDE

A67

SIDE AND REAR BASE RAILS

Assemble lengths of side base rails (2 pcs.)

together with a lap joint. Align large holes.

Repeat for other side.

NOTE - for product sizes 6x4, 6x5 and 6x6

these parts are in one full length piece.

Repeat above procedure to assemble lengths

of rear base rails No. 64H (2 pcs.).

STEP

L06

INSIDE

USE SELF TAPPING SCREWS..10mm (3/8") LONG

See Pages 4 and 5 for profile,

correct part number and quantity

required for your building.

OUTSIDE SIDE BASE RAIL

LARGE

6mm (1/4") HOLES

SIDE BASE RAIL

USE 10mm (3/8") LONG BOLTS AND NUTS

VIEWED FROM

INSIDE BUILDING

INSIDE

OUTSIDE

ENTRY RAMP

No. 610H

FRONT BASE RAIL

No. 62H

FRONT BASE RAIL

No. 62H

VIEWED FROM

INSIDE BUILDING

WIDE FLANGE ON OUTSIDE

FRONT BASE RAILS AND ENTRY RAMP

Space out lengths of front base rails No. 62H (2 pcs.) and

fasten entry ramp No. 610H between lengths.

STEP

BASE FRAME ASSEMBLY

Assemble all 4 base rails into a base frame in proper position

on your foundation. Use 10mm (3/8") self tapping screws on

front and on back corners.

Check base frame for squareness by measuring diagonal

corners. Your measurements should be equal. See "A"

STEP

E07

BACK CORNER

REAR BASE RAIL

DOORWAY

SOLID

FOUNDATION

"A"

FRONT CORNER

FRONT BASE RAIL AND

ENTRY RAMP

SIDE BASE RAIL

DOORWAY

* AFTER ASSEMBLY CHECK BASE DIMENSIONS (SEE PAGE 3) TO VERIFY CORRECT POSITION OF RAILS.

USE SELF TAPPING SCREWS...10mm (3/8") LONG

* AFTER ASSEMBLY CHECK BASE DIMENSIONS (SEE PAGE 3) TO VERIFY CORRECT POSITION OF RAILS.

WARNING!

DO NOT ERECT ON A WINDY DAY. THE LARGE WALL

ANDROOFPANELSPROVIDEALARGESURFACEAND

THE WIND COULD EASILY CARRY THEM AWAY. ANY

BUILDING LEFT PARTLY CONSTRUCTED MAY BE SE-

RIOUSLY DAMAGED IF LEFT IN THIS STATE.

STEP

L08

SIDE AND REAR TOP RAILS

Assemble lengths of side top rails (2 pcs.) together with a lap joint...see

"A". Fasten to top of corner panels. Repeat for other side. NOTE - for

sizes 6x4, 6x5 and 6x6 these parts are in one full length piece.

Repeat above procedure to assemble and fasten lengths of rear top rail

No. 640H (2 pcs.)...See "B".

STEP

USE SELF TAPPING SCREWS

...10mm (3/8") LONG

CORNER PANELS

Position rear corner panels and fasten to rear

and side base rails...with narrow flange of

panel along the side of the building.

Position front half corner panels and fasten to

front and side base rails...with narrow flange

of panel along the side of building.

See Pages 4 and 5 for profile,

correct part number and quantity

required for your building.

DOORWAY

REAR

SIDE

SIDE TOP RAIL

REAR TOP RAIL

No. 640H

SIDE

"A"

REAR "B"

USE 10mm (3/8") LONG

BOLTS AND NUTS

STEP

L09

DOOR TRACK INSTALLATION

Install 4 door glides No. A67 into door track. See "A"

Fasten door track to the front corner panels with screws.

IMPORTANT: PLACE EDGE OF DOOR TRACK WITH

THE MOST HOLES FACING THE OUTSIDE.

STEP

USE SELF TAPPING SCREWS...10mm (3/8") LONG

SPLICED ASSEMBLY OF DOOR

TRACK AND DOOR FASCIA

Assemble lengths of door track No. 66H

(2 pcs.) together with door fascia No. 635H. See Pages 4 and 5 for profile,

correct part number and quantity

required for your building.

FRONT

SIDE

Door Track

"A"

DOOR GLIDE

No. A67

DOOR FASCIA No. 635H

MOST HOLES ON THIS SIDE

MOST HOLES ON THIS SIDE DOOR TRACK

No. 66H

VIEWED FROM INSIDE

DOORWAY

SLIDE DOOR GLIDES

INTO DOOR TRACK

INSIDE

OUTSIDE

USE SELF TAPPING SCREWS...10mm (3/8") LONG

STEP

AL10

DOOR JAMBS AND FRONT MIDWALL BRACE

Remove corner panel screws as necessary and install door jambs No. 69G on

each side of entry ramp...sliding door jamb under the half corner panel and

under door fascia. Fasten at base rail --- then fasten through the door fascia and

door jamb into the side of door track. Replace half corner panel screws.

Fasten door jamb to half corner panels at midwall height with 10mm (3/8") bolts

andnuts.

Install front midwall brace No.628H on each side of doorway.

Use short bolts 6mm (1/4").

DOOR TRACK

USE SELF TAPPING SCREWS...10mm (3/8") LONG

DOOR FASCIA

DOOR JAMB

No. 69G

DOOR FASCIA

DOORWAY FRONT MIDWALL BRACE

No. 628H

USE SHORT 6mm (1/4") BOLTS AND NUTS

DOOR JAMB

No. 69G

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SPACEMAKER Entreposage extérieur

SPACEMAKER

SPACEMAKER RGB1012ONEU Manuel d'utilisation et d'entretien

SPACEMAKER

SPACEMAKER RGB108ONEU Manuel d'utilisation et d'entretien

SPACEMAKER

SPACEMAKER PS53 Instructions d'utilisation

SPACEMAKER

SPACEMAKER RPT84ONEU Manuel d'utilisation et d'entretien

SPACEMAKER

SPACEMAKER SBS64EU Manuel utilisateur

SPACEMAKER

SPACEMAKER RGB1010ONEU Manuel d'utilisation et d'entretien

SPACEMAKER

SPACEMAKER RGB86ONEU Manuel d'utilisation et d'entretien

SPACEMAKER

SPACEMAKER PS63 Instructions d'utilisation

SPACEMAKER

SPACEMAKER Versa-shed VRS53AN01 Manuel utilisateur

SPACEMAKER

SPACEMAKER RGB88ONEU Manuel d'utilisation et d'entretien

SPACEMAKER

SPACEMAKER PS43EU Series Instructions d'utilisation

SPACEMAKER

SPACEMAKER PS63EU Instructions d'utilisation

SPACEMAKER

SPACEMAKER VERSA-SHED EVRS53 Series Instructions d'utilisation

SPACEMAKER

SPACEMAKER VERSA-SHED EVRS63 Instructions d'utilisation

SPACEMAKER

SPACEMAKER PS63 Instructions d'utilisation

SPACEMAKER

SPACEMAKER 90174CL Series Instructions d'utilisation

Manuels Entreposage extérieur populaires d'autres marques

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Manuel utilisateur

TYGO

TYGO Nyland Manuel utilisateur

Duratuf

Duratuf GL105 Manuel utilisateur

Viking

Viking SD5300SS Manuel technique

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Manuel utilisateur

ModuLaro

ModuLaro Lojo WC202200 Manuel utilisateur

Lifetime

Lifetime 6418 Manuel utilisateur

rollaway container

rollaway container ARPCA24 Manuel utilisateur

Duratuf

Duratuf Havelock Manuel utilisateur

X-METAL

X-METAL 4065 Manuel utilisateur

Outdoor Life Products

Outdoor Life Products FP2030 F Manuel utilisateur

Royalcraft

Royalcraft Faro 295L Storage Box Manuel utilisateur

Riverlea

Riverlea Duratuf KIWI KS3 Manuel utilisateur

OLT

OLT GS84D-FJ-Plywood Manuel utilisateur

Rubbermaid

Rubbermaid 5L45 Manuel utilisateur

garofalo

garofalo TUSCANY EVO Manuel utilisateur

Duratuf

Duratuf Kiwi MK1 Manuel utilisateur

Eden

Eden CA2988 Manuel utilisateur