Southco EA-BT Series Manuel utilisateur

EA-BT Series Access Controller

Quick Install Guide

J-EA-BT-2-M_revC Page 1 of 2

PRN P2017-1718 (WJB/DJK)

Package Contents

EA-BT Series Access Controller

Serial Number and Checksum Label

Quick Install Guide

EA-BT Series Access Controller

1. Admin Button

Features

Multi-door output

Wiegand DATA inputs for external reader connection

Back-lit admin button for controller status

For indoor use only

Specifications

Supply Voltage: 12VDC

Standby Current: 20mA typical at 12VDC

Operating Current: 50mA maximum at 12VDC

Relay Output (x1): 750mA @ 12/24VDC/AC

CMD Output (x2): 15mA, up to 9VDC (each)

Read Distance: up to 30 feet

DATA Signal Voltage: 5VDC

DATA Pulse Interval Time:40µs

DATA Signal Delay: 2ms

DATA Length: 26 and 35 bits

Overall Dimensions: 108.95 x 45 x 19.5 mm

Step 1 - Mounting and Installation

Please refer to Southco trade drawing J-EA-BT-2.

NOTE: Be sure to record the 7-digit serial number and 4 character

checksum (81xxxxx-xxxx) on the label included with the controller. The

serial number and checksum are also on the rear of the controller and the

box it is shipped in.

The EA-BT has a 14-wire stripped and tinned harness, as described below:

Color

Description

Red

12VDC

Black

GND

Yellow

Relay –Common

Blue

Relay –Normally Open

White/yellow

CMD Output #1

White/orange

CMD Output #2

Grey

reserved (do not use)

White/red

Door Status Sensor (not active)

White

DATA1 input

Green

DATA0 input

White/brown

reserved (do not use)

White/black

reserved (do not use)

Brown

reserved (do not use)

Orange

reserved (do not use)

An example connection diagram is shown below.

Using the above connection diagram, the electromechanical latches are

operated independently and simultaneously.

Independent control –An electromechanical latch’s command input can be

connected to one of the two CMD outputs.

Simultaneous control –Multiple electromechanical latches’ command

inputs can be connected to the Relay (NO) output.

Southco EML

Relay (NO)

CMD Output

R4-EM 1 & 2 Series



R4-EM 4 & 6 Series



R4-EM 5 & 7 Series



R4-EM 8 Series



R4-EM 9 Series



H3-EM Series



EM-10 Series



EM-05 Series



EA-BT Output / Latch Compatibility

EA-BT Series Access Controller

Quick Install Guide

J-EA-BT-2-M_revC Page 2 of 2

PRN P2017-1718 (WJB/DJK)

Wiegand DATA Inputs

The DATA1 and DATA0 Wiegand data inputs can be used to connect the

EA-BT to an external reader, as shown below, for prox card authentication

and access control.

Step 2 –Download the Mobile App

The EA-BT is configured to be used with the VIZpin® cloud-based access

control system.

To get started:

1. Ensure EA-BT installation is complete.

2. Download the VIZpin® mobile application and register using the

QR code below or search “VIZpin Smart” on the App Store or

Google Play store.

iOS 8 or above

ANDROID OS 5.0 or above

NOTE: BLUETOOTH® LE or BLUETOOTH Smart phone only.

(ver 4.2, or higher)

Step 3 –Sign up for VIZpin® Partner Account Access

If purchased from a Southco partner, please contact your partner for

account access, otherwise, go to www.southco.com/vizpin to request your

Partner portal login.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/television technician for help.

Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment

under Federal Communications Commission rules.

Industry Canada Compliance Statement

CAN ICES-3(B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d’en compromettre le fonctionnement.

Trademark Statements