Sony RM-TP501E Manuel utilisateur
3-865-783-16(1)
Remote
Commander
1998 by Sony Corporation
RM-TP501E
Operating Instructions
Mode d’emploi
GB
FR
2GB
Precautions
CAUTION (Lithium battery)
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Discard
used batteries according to the manufacturer’s
instructions.
On operation
Before connecting other components, be sure to turn off and
unplug the amplifier.
On cleaning
Clean the cabinet, panel and controls with a soft cloth slightly
moistened with a mild detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent such as alcohol or
benzine.
If you have any question or problem concerning your
remote commander, please consult your nearest Sony
dealer.
About This Manual
• The following icon is used in this manual:
zIndicates hints and tips for making the task easier.
3GB
TABLE OF CONTENTS
Preparations 4
Compatible Components and Functions 4
Preparing the Commander 5
Screen Hierarchy 8
Location of Parts and Basic
Operations 9
Front panel 9
Rear panel 10
Operation 11
Basic Operations 11
Example: Operating a CD Player 13
Example: Recording from CD to MD 14
Selecting Sound Fields 15
Adjusting Sound Fields 17
Adjusting the Commander’s Operating
Environment 19
Additional information 23
Precautions during use 23
Troubleshooting 24
Specifications 25
Index 25
GB
4GB
Preparations
This chapter describes how to prepare
the remote commander for operation.
Be sure to read this section before
operating.
Compatible Components
and Functions
This unit is a remote control system that utilizes infrared
rays to control an amplifier and AV components
connected to the amplifier.
Compatible Components
This unit can be used to operate Sony AV components as
well as AV components manufactured by other
manufacturers. Set up is necessary in order to operate
components manufactured by other companies (see page
19).
Note
Depending on the component, control may not be possible using
this unit.
Functions
This unit is a bidirectional remote commander. Not only
does it transmit infrared rays for operation of the
amplifier, it can also receive infrared rays emitted by the
amplifier to display characters and other information
supplied by other components connected to the amplifier
with a CONTROLA1 cord.
5GB
Preparations
Please be sure to carry out the procedures described in
“Setting up the commander” on page 6 after inserting the
batteries.
Inserting batteries into the commander
Insert the four size-AA (LR6) alkaline batteries (for
commander operation) and lithium battery (for
preservation of the commander’s internal memory).
1Remove the battery compartment cover.
2Insert the alkaline batteries.
3Insert the lithium battery.
After wiping the lithium battery thoroughly with a
dry cloth, insert it into the compartment with the
positive (+) pole side facing up.
Preparing the Commander
4Close the battery compartment cover.
After inserting the batteries, touching the touch panel
turns on the light and displays the touch panel (LCD)
adjustment screen. Follow the procedure on the next
page for touch panel adjustment and initial
communication.
Notes
• The LCD lights up when touched.
• VOL +/–, MUTING and SLEEP can be used even when the
LCD is not lit.
• If the commander is not used for approx. 10 seconds, the LCD
turns off automatically (Auto Off function).
Push in the direction
of arrow
Always insert the negative (–) pole
side of batteries first
Size-AA alkaline batteries
Coin shaped lithium
battery CR2032
Positive (+) pole side up
]
]
}
}
]
}
]
}
6GB
Preparations
Touch panel adjustment
3Adjust the position of the touch panel’s LCD.
Touch the center of each of the 4 dots with the touch
pen. When all 4 dots have been touched “Adjusted”
appears, a buzzer sounds, and the initial
communication screen appears.
Caution
Touch panel adjustment must be carried out for proper panel
operation. If used without adjustment, the ”Touch Panel
Adjustment” screen appears each time the LCD lights up.
Initial communication
4Press Uon the amplifier to turn on the amplifier.
5Point the commander’s transmitter/receiver section
toward the amplifier, and touch OK.
Once initial communication with the amplifier has
been established, the commander is ready to operate
the amplifier.
Setting up the commander
Please be sure to carry out the following 1 to 5 procedures
for preparation of the commander.
The commander’s panel is touch sensitive and can be
operated by simply touching it.
1Remove the touch pen.
When returning the touch pen, always slide it in tip
first.
Caution
Use only the touch pen provided with this unit or the soft tip
of your finger to operate the touch panel. Using a
commercially available writing utensils may damage the
panel and make correct operation impossible. If the tip of the
touch pen is damaged, or the touch pen is lost, please consult
your nearest Sony dealer.
2Turn CONTRAST to adjust brightness of the LCD.
Touch the 4 dots with the touch pen.
Preparing the Commander
Pen holder
Remove by sliding out
CONTRAST control
7GB
Preparations
Note
• To ensure good communication conditions, carry out initial
setup from directly in front of, and close to the amplifier.
• Do not move the unit during initial setup.
If a communication error occurs during setup
An error message will be displayed.
• Touching OK will return to the step 5 setup screen.
• Touching SKIP goes to the regular screen without
carrying out initial setup. Although operation is
possible in this condition, functions not included on the
amplifier will be displayed, and some buttons will not
be operable. Also, the initial setup screen will appear
each time the touch panel is turned on.
Note
The commander receives and displays data transmitted from the
amplifier. Communication errors may occur if the commander’s
transmitter/receiver section is not directed properly toward the
amplifier.
Be sure to point the commander’s transmitter/receiver section
towards the amplifier.
When replacing the batteries
To ensure preservation of the commander’s internal
memory when replacing batteries, be sure to observe the
following cautions.
When to replace batteries
When the batteries become weak, a warning sounds and a
message is displayed. Replace batteries as instructed by
the message.
How to remove the lithium battery
Notes
• Disc titles and song titles downloaded from the CD changer are
memorized in the commander. The lithium battery is used for
preservation of this memory. If the unit is used with an
exhausted battery, the settings memorized in the commander
will be erased. Please replace the battery as soon as the message
appears.
• Replace the alkaline batteries with new batteries as soon as
their charge is exhausted. If the unit is used with exhausted
batteries, exhaustion of the lithium battery used to maintain
memory will be quickened and the memorized settings may be
erased.
• The life span of batteries may be shortened depending on the
conditions in which the commander is used.
• If the alkaline batteries and lithium battery become exhausted
at the same time, replace the alkaline batteries first. Replacing
the lithium battery first will erase the data memorized in the
commander.
• When replacing the alkaline batteries, always replace all 4
batteries with new ones.
• After replacing batteries, be sure to carry out touch panel
adjustment (page 6).
1 m ~ 2 m
Replace alkaline
batteries. Replace lithium
battery.
8GB
Preparations
The following diagram shows the basic composition of this unit’s screen hierarchy.
FUNCTION screen
Screen Hierarchy
Normally, the
FUNCTION
screen is
displayed.
To display a
different screen,
touch the left side
of the LCD.
SOUND FIELD screen
SETUP screen
Screen for selection and
adjustment of the sound fields
and equalizer (see page 16~20).
Screen for setting up the
operation environment and
control of components made by
other manufacturers (page 20).
Touch when the song titles of
a CD or MD being played
back are not displayed
correctly or when all the
soundfield parameters are
grayed out.
Screens for selection and
operation of components
connected to the amplifier.
Screen for recording audio
and video from one
component to another (see
page 14).
RELOAD...
9GB
Location of Parts and Basic Operations
Front panel
1BACK LIGHT/COMMANDER OFF
Press to turn the backlight on or off. Hold down for
about 2 seconds to turn the LCD off. When the LCD is
off, press to turn on the LCD and backlight.
• To prolong use of the batteries, if there are no commands
entered in the touch panel for 10 seconds, the LCD
automatically turns off.
• To view the LCD display without turning on the backlight,
touch the touch panel when both the backlight and LCD
are off.
2Touch panel
Touch to operate. The commander turns on
automatically.
3VOL +/– buttons
Use to adjust the volume of the amplifier.
4JOG DIAL control
Rotate to scroll through items in a list (etc.).
Push to select the highlighted item.
5SYSTEM/STANDBY button
Normally used to turn off all Sony components. Can
also be used to turn the amplifier on or off depending
on the settings made in the SETUP screen (see page
22).
6MUTING button
Use to mute the sound of the amplifier.
7CONTRAST control
Use to adjust the contrast of the LCD.
8SLEEP button
Use to operate the amplifier’s sleep function. The
sleep settings appear in the amplifier’s display, not the
commander’s LCD.
Location of
Parts and Basic
Operations
This chapter provides information
about the locations and functions of
the buttons and controls on this unit.
123
4
5
6
7
8
10GB
Location of Parts and Basic Operations
Rear panel
1Transmitter/receiver section
Transmits and receives infrared signals to and from
the amplifier.
2Battery cover
3Touch pen
4SYSTEM/STANDBY button
Normally used to turn off all Sony components. Can
also be used to turn the amplifier on or off depending
on the settings made in the SETUP screen (see page
22).
5Touch pen holder
Pull out and insert touch pen when not in use.
12
3
4
5
Autres manuels pour RM-TP501E
1
Table des matières
Langues :
Autres manuels Sony Télécommande
Sony
Sony RM-V8A Manuel utilisateur
Sony
Sony RM-VL700T Manuel utilisateur
Sony
Sony RM-V8A Manuel utilisateur
Sony
Sony Remote Commander RM-VZ320 Manuel utilisateur
Sony
Sony RM-XM10B Manuel utilisateur
Sony
Sony RM-VPR1 Manuel utilisateur
Sony
Sony Blu-ray Disc Remote Control Manuel utilisateur
Sony
Sony RMT-VP1K Manuel utilisateur
Sony
Sony RMF-YD001 Manuel utilisateur
Sony
Sony RM-E80 Manuel utilisateur
Sony
Sony Remote Commander RM-V21 Manuel utilisateur
Sony
Sony AIR-RM10 - Remote Commander Manuel utilisateur
Sony
Sony MKS-8080 Manuel utilisateur
Sony
Sony RM-V301 Manuel technique
Sony
Sony RM-VL610T Manuel utilisateur
Sony
Sony HomeShare RMN-U1 Manuel utilisateur
Sony
Sony RM-XM10W Manuel utilisateur
Sony
Sony RM-VL610A (RM-VL610A Remote Commander®) Guide de l'administrateur
Sony
Sony RM-DC2 Manuel utilisateur
Sony
Sony RM-VL610A (RM-VL610A Remote Commander®) Manuel utilisateur
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
