Sony RM-PP505L Manuel utilisateur

Remote

Commander

Operating Instructions

4-236-328-11(2)

RM-PP505L

Owner’s Record

The model and serial numbers are located on the rear panel. Record the serial number

in the space provided below. Refer to them whenever you call upon your Sony dealer

regarding this product.

Model No. Serial No.

Precautions

On safety

Should any solid object or liquid fall into the cabinet,

unplug the receiver and have it checked by qualified

personnel before operating it any further.

On operation

Before connecting other components, be sure to turn

off and unplug the receiver.

On cleaning

Clean the cabinet, panel and controls with a soft cloth

slightly moistened with a mild detergent solution. Do

not use any type of abrasive pad, scouring powder or

solvent such as alcohol or benzine.

If you have any question or problem

concerning your remote, please consult your

nearest Sony dealer.

About this manual

The instructions in this manual are for model

RM-PP505L. Check your model number by

looking at the lower right corner of the front

side.

Before you use your

remote

Check that you received the following item

with the remote:

R6 (size-AA) batteries (2)

Inserting batteries into the

remote

Insert two R6 (size-AA) batteries with the +

and – properly oriented in the battery

compartment. When using the remote, point it

at the remote sensor on the receiver.

Tip

Under normal conditions, the batteries should last for

about 6 months. When the remote no longer operates

the receiver, replace both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or

humid place.

• Do not use a new battery with an old one.

• Do not expose the remote sensor of the receiver to

direct sunlight or lighting apparatuses. Doing so

may cause a malfunction.

• If you don’t use the remote for an extended period

of time, remove the batteries to avoid possible

damage from battery leakage and corrosion.

Table of Contents

Location of Parts and Basic

Remote Operations

Parts description .................................... 4

Table of buttons that you can use to

control each component .................. 9

Advanced Remote Operations

Programming the remote ..................... 10

Learning the commands of your

components ................................... 13

Performing several commands in

sequence automatically

(Macro Play).................................. 14

Selecting the mode of the remote ........ 15

Additional Information

Troubleshooting.....................Back cover

Specifications ........................Back cover

This chapter provides information on the

location of buttons and how to use them to

perform basic operations.

However, some functions explained in this

section may not work depending on the model

of the receiver.

For the functions of the receiver you purchased,

refer to the Operating Instructions supplied

with the receiver.

Parts description

Location of Parts and Basic Remote

Operations

1Function buttons

Press one of the buttons to select the

component you want to use. When you

press a button, the receiver turns on. The

components are factory assigned to the

buttons as follows. When you want to

assign other components, program the

remote following the steps on page 10.

Button(s) Assigned

component(s)

VIDEO1 VCR (VTR mode 3)

VIDEO2 VCR (VTR mode 1)

VIDEO3 VCR (VTR mode 2)

DVD/LD DVD player

TV/SAT TV tuner

TAPE Tape deck

MD/DAT MD deck

CD/SACD CD player

TUNER Built-in tuner

PHONO Turntable

See the table on page 9 for information on

the buttons that you can use to control each

component.

Note that the function buttons are factory-

set as described in the table above. If you

want to change the factory setting of the

buttons to match your particular

components, do the procedure

“Programming the remote” on page 10.

>10

MONITOR 2ND ROOM

VIDEO 1 VIDEO 2 VIDEO 3 DVD/LD TV/SAT

TAPE

TV/VIDEO

MACRO 1

MACRO 2

CLEAR

– SUB CH +

– VOL +

POSITION SWAP

MODE

ENTER ANT

TV/VTR

D. SKIP/

CH/PRESET

MD/DAT CD/SACD TUNER PHONO

SHIFT DISC

JUMP

A.F.D.

DISPLAY TEST

TONE NIGHT

MODE

SCREEN

MAIN

EXIT/

RETURN

TITLE/

GUIDE

ENTER/

EXEC

MULTI/2CH

A. DIRECT

EQ/

TONE

MUTING

MODE 2CH PRESET

P IN P

– /– –

SOUND FIELD

D.TUNING

AV1 AV2 3RD

(SOURCE)

WIDE

/11 /10 /12

SLEEP AV

? / 1

? / 1

SYSTEM

STANDBY

USE MODE

MASTER

VOL

.Mm

nNX

Location of Parts and Basic Remote Operations

2Remote mode buttons

Press to select the mode of the remote (page

15).

3MACRO 1, 2 buttons

Press to use Macro Play function (page 14).

4SOUND FIELD buttons

A.F.D. button

Press to set the receiver to automatically

select the appropriate sound field for the

input signal.

This button can be used only with receivers

that have digital inputs.

MODE +/– button

Press to select sound fields.

2CH button

Press to turn the sound field off and listen to

2 channel stereo sound.

Multi channnel source is also downmixed to

a 2 channel stereo sound.

PRESET button

Press to select CINEMA STUDIO A, B, or

C, etc.

5MULTI/2CH A. DIRECT button

Press to select the multi channel input

sources.

continued

6EQ/TONE button

Press to turn the tone effect on or off.

Note that if you have adjusted the tone

using the MAIN MENU button and cursor

buttons, the adjusted tone will be produced

whenever you turn on the tone effect.

7MUTING button

Press to mute the sound.

8ON SCREEN button

Press to display the menus of the receiver

on the TV screen.

9MASTER VOLUME +/– buttons

Press to adjust the volume level of all

speakers at the same time.

0MAIN MENU button

Press to select the cursor mode of the

receiver (LEVEL, SURROUND, or EQ).

qa NIGHT MODE button

Press to select NIGHT MODE.

qs TEST TONE button

Press to output a test tone.

qd SLEEP button

Press repeatedly to activate the sleep

function and the duration which the receiver

turns off automatically.

Parts description (continued)

qf AV ?/1 switch

Press to turn the selected audio and video

components under the function button, on or

off.

If you press the ?/1 switch at the same

time, it will turn off the main component

and other Sony audio/video components

(SYSTEM STANDBY).

Note

The function of the AV ?/1 switch changes

automatically each time you press the function

buttons (1). Depending on the component, the

above operation may not be be possible or may

operate differently than described.

qg ANT TV/VTR / DISC button*

Press repeatedly to select the signal to be

output from the antenna terminal of the

VCR (TV signal or video signal). With a

CD player, press to select discs (mega

storage CD player only).

qh ENTER button

Press to enter the selection.

qj D.SKIP/CH/PRESET +/– buttons*

If you selected tuner:

Press to scan and select preset stations.

If you selected TV, VCR, or SAT:

Press to select preset channels.

If you selected CD player:

Press to skip discs (CD player with multi-

disc changer only).

qk AV MENU button

Press to display the menus of the VCR,

satellite tuner, or DVD.

ql EXIT/RETURN button

After pressing the MAIN MENU, AV

MENU, or TITLE GUIDE button, press to

return to the previous menu or exit the

menu.

* The function of these buttons switch automatically

each time you press the function buttons (1). The

above explanation is intended to serve as an

example only. Therefore, depending on the

component, the above operation may not be

possible or may operate differently than described.

>10

MONITOR 2ND ROOM

VIDEO 1 VIDEO 2 VIDEO 3 DVD/LD TV/SAT

TV/VIDEO

CLEAR

– SUB CH +

– VOL +

POSITION SWAP

MODE

ENTER ANT

TV/VTR

D. SKIP/

CH/PRESET

CD/SACD TUNER PHONO

SHIFT DISC

JUMP

A.F.D.

DISPLAY TEST

TONE NIGHT

MODE

SCREEN

MAIN

EXIT/

RETURN

TITLE/

GUIDE

ENTER/

EXEC

MULTI/2CH

A. DIRECT

EQ/

TONE

MUTING

MODE 2CH PRESET

P IN P

– /– –

SOUND FIELD

D.TUNING

AV1 AV2 3RD

(SOURCE)

WIDE

/11 /10 /12

SLEEP AV

? / 1

? / 1

SYSTEM

STANDBY

USE MODE

MASTER

VOL

.Mm

nNX

TAPE

MACRO 1

MACRO 2

MD/DAT

Location of Parts and Basic Remote Operations

continued

w; Cursor buttons (U/u/I/i), ENTER/

EXEC button

After pressing the MAIN MENU, AV

MENU, or TITLE/GUIDE button, use the

cursor buttons to make specific settings,

then press the ENTER/EXEC button to

enter the selection.

wa TITLE/GUIDE button*

Press to display DVD titles or guide menus.

ws AV DISPLAY button

Press to select the information displayed on

the TV screen.

wd Operation buttons*

The following table describes the

component operated by each button and the

function of the buttons. See the table on

page 10 for information on the buttons that

you can use to control each component.

Button(s)

./>

m/M

wf SHIFT / >10 button*

If you selected tuner:

Press repeatedly to select a memory page

for presetting radio stations or tuning to

preset stations.

If you selected VCR, TV, LD player, tape

deck, MD deck, or CD player:

Press before inputting a channel or track

number of eleven or higher.

wg CLEAR / -/-- / D.TUNING button*

If you selected DVD player:

Press if you made a mistake when you press

the numeric buttons.

If you selected TV or VCR:

Press to select the channel entry mode,

either one or two digit.

wh SEARCH MODE button

Press to select the search mode of DVD

player.

wj Indicator*

Lights up whenever any button on the

remote is pressed.

wk USE MODE button

Use to program the remote.

* The function of these buttons switch automatically

each time you press the function buttons (1). The

above explanation is intended to serve as an

example only. Therefore, depending on the

component, the above operation may not be

possible or may operate differently than described.

Function

Skips tracks.

Fast forwards or rewinds.

Searches tracks in the forward or

backward direction.

Starts play on the reverse side of

the cassette.

Starts play. (Starts play on the

front side of the cassette.)

Pauses play or recording or starts

recording when the component is

in recording standby.

Stops play.

Parts description (continued)

wl Numeric buttons (1 to 0)*

Press to select channel numbers.

e; JUMP button

Press to toggle between the previous and the

current channels.

ea POSITION button

Press to change the position of the small

picture**.

es SWAP button

Press to swap the small and large

pictures**.

ed P IN P button

Press to activate the picture-in-picture

function**.

ef MUTING button

Press to mute the sound.

eg VOLUME +/– buttons

Press to adjust the volume of TV.

eh SUB CH +/– buttons

Press to change the sub channel selection.

ej WIDE button

Press to switch the TV to the wide mode.

wk TV/VIDEO button

Press to select the TV input signal.

el MONITOR button

Press to active TV control buttons. The

button lights up. Press again to restore

original category.

* The function of these buttons switch automatically

each time you press the function buttons (1). The

above explanation is intended to serve as an

example only. Therefore, depending on the

component, the above operation may not be

possible or may operate differently than described.

**Only with Sony TVs with the picture-in-picture

function.

TV operation

After pressing the MONITOR button, the

button lights up and you can use the following

buttons to operate TV.

>10

MONITOR 2ND ROOM

VIDEO 1 VIDEO 2 VIDEO 3 DVD/LD TV/SAT

TV/VIDEO

CLEAR

– SUB CH +

– VOL +

POSITION SWAP

MODE

ENTER ANT

TV/VTR

D. SKIP/

CH/PRESET

CD/SACD TUNER PHONO

SHIFT DISC

JUMP

A.F.D.

DISPLAY TEST

TONE NIGHT

MODE

SCREEN

MAIN

EXIT/

RETURN

TITLE/

GUIDE

ENTER/

EXEC

MULTI/2CH

A. DIRECT

EQ/

TONE

MUTING

MODE 2CH PRESET

P IN P

– /– –

SOUND FIELD

D.TUNING

AV1 AV2 3RD

(SOURCE)

WIDE

/11 /10 /12

SLEEP AV

? / 1

? / 1

SYSTEM

STANDBY

USE MODE

MASTER

VOL

.Mm

nNX

TAPE

MACRO 1

MACRO 2

MD/DAT

ed es

Location of Parts and Basic Remote Operations

Table of buttons that you can use to control each component

Component CD DAT MD Tape LD VCR TV

Satellite Video

DVD

player deck deck deck player

tuner/ CD

player

(A and B)

Cable box player

Button(s)

AV ?/1 zzz zzzzzz

Numeric buttons zzz zzzzzzz

SHIFT >10 zzzzzzz

VOL – z

O(Return) zzz

Nzzzzzz zz

VOL + z

Xzzzzzz zz

MUTING z

xzzzzzz zz

./> z z z z** zz zz

m/M z z z z z z z z

SUB CH +/– z

D.SKIP z*zzz*

CH/PRESET +/– zzz

ANT TV/VTR z

DISC z*z

CLEAR z

-/-- D.TUNING zz

AV MENU zzz

TITLE/GUIDE zz

Cursor buttons zzz

ENTER/EXEC zzz

EXIT/RETURN zz zzz

AV DISPLAY zzzzzz

TV/VIDEO z

SEARCH MODE z

* With a multi-disc changer only.

**B deck only.

This chapter describes how to change the

factory setting of a function button and how to

set the remote to control non-Sony

components.

Programming the remote

You can program the remote to control non-

Sony components by changing the code. Once

the control signals have been memorized, you

can use those components as part of your

system.

Furthermore, you can also program the remote

for Sony components that the remote is unable

to control. Note that the remote can only

control components that accept infrared

wireless control signals.

Note

When you assign a component to the MONITOR

button, you can operate the programmed component

without changing the function of the receiver.

1Press AV ?/1 while pressing down USE

MODE.

The indicator lights.

2Press the function button (including

MONITOR) for the component you want

to control.

For example, if you are going to control a

CD player, press CD.

3Press the numeric buttons to enter the

numeric code (or one of the codes if

more than one code exists)

corresponding to the component and

the maker of the component you want

to control.

See the tables on pages 11 and 12 for

information on the numeric code(s)

corresponding to the component and the

maker of the component (the first digit and

the last two digits of the numeric code

correspond to the category and the maker’s

code respectively.)

Advanced Remote Operations 4Press ENTER.

Once the numeric code has been verified,

the indicator slowly lights twice and the

remote automatically exits the programming

mode.

5Repeat steps 1 to 4 to control other

components.

To cancel programming

Press USE MODE during any step. The remote

automatically exits the programming mode.

Tips

• If programming is unsuccessful, check the

following:

– If the indicator does not light up in step 1, the

batteries are weak. Replace both batteries.

– If the indicator lights 4 times in quick succession

while entering the numeric code, an error has

occurred. Start again from step 1.

• To activate the function after programming, press

the programmed button to activate the function you

want.

Notes

• The indicator turns off while a valid button is

pressed.

• In step 2, if several function buttons are pressed,

only the last pressed button is valid.

• In step 3, if a function button is pressed, the new

function is selected and the programming procedure

returns to the beginning of step 3.

• For the numeric codes, only the first three numbers

entered are valid.

To clear the memory of the remote

To clear all programmed and learned signals,

do the following to reset the remote to factory

settings.

Press ?/1, AV ?/1 and MASTER VOL – at

the same time.

The indicator lights 3 times, then goes off.

Table des matières

Autres manuels Sony Télécommande

Sony

Sony RM-V111T Manuel utilisateur

Sony

Sony RM-AX4000 - Integrated Remote Commander Manuel utilisateur

Sony

Sony RM-X4S Operating Instructions (primary... Manuel utilisateur

Sony

Sony RM-X5S Manuel utilisateur

Sony

Sony RM-VJ1 Manuel utilisateur

Sony

Sony FY15 Manuel utilisateur

Sony

Sony PlayStation Portal Manuel utilisateur

Sony

Sony RM-AV2000 Operating Instructions (primary... Manuel utilisateur

Sony

Sony RM-VL710 Guide de l'administrateur

Sony

Sony Vaio VGP-BRMP10 Manuel utilisateur

Sony

Sony RM-AX4000 - Integrated Remote Commander Guide de l'administrateur

Sony

Sony RM-X6S Manuel utilisateur

Sony

Sony RMF-TX300E Manuel utilisateur

Sony

Sony RM-X11M Manuel utilisateur

Sony

Sony UPA-P100MD Manuel utilisateur

Sony

Sony RM-VZ220T Manuel utilisateur

Sony

Sony RM-VZ950T Manuel utilisateur

Sony

Sony RM-V201T Manuel utilisateur

Sony

Sony RMF-TX910U Manuel utilisateur

Sony

Sony RM-IP500 Manuel utilisateur

Sony

Sony RM-LP204 Manuel utilisateur

Sony

Sony RM-X7BT Manuel utilisateur

Sony

Sony RM-X60M/L Manuel utilisateur

Sony

Sony RM-V401 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation