Sony A 7 R IV Manuel utilisateur
ExpoDisc Custom White Balance Procedures
Sony Cameras
Sony A7 R IV
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. From the MENU navigate to the Camera Settings1 screen and select White
Balance and then select Custom 1 - Custom 3, and then press the right side
of the control wheel.
4. Select Set and then press the center of the control wheel.
5. Aim the camera in the appropriate direction for the given lighting condition
and press the center of the control wheel. See the ExpoDisc Instruction
Manual for more information on where to aim the camera.
6. After the shutter sound beeps, the calibrated values (ColorTemperature and
Color filter) are displayed.
7. Press the center of the control button again. The monitor returns to the menu
display with the memorized white balance retained. The custom white
balance setting registered in this operation is effective until a new setting is
registered.
8. If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
9. From the White Balance menu, select Custom 1 (or whichever Custom setting
you selected in Step 3).
10.Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony A7 R III
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. From the MENU navigate to the Camera Settings1 screen and select White
Balance and then Custom Setup.
4. Aim the camera in the appropriate direction for the given lighting condition
and press the center of the control wheel. See the ExpoDisc Instruction
Manual for more information on where to aim the camera.
5. After the shutter sound beeps, the calibrated values (ColorTemperature and
Color filter) are displayed.
6. Press the center of the control button again. The monitor returns to the
recording information display with the memorized white balance retained.
The custom white balance setting registered in this operation is effective until
Copyright, 2020 ExpoImaging, Inc.
“Sony” and the Sony camera models listed are trademarks of Sony, Inc.
a new setting is registered.
7. If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
8. From the White Balance menu, select (Custom 1).
9. Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony A7 R II
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. From the MENU navigate to the Camera Settings1 screen and select White
Balance and then Custom Setup.
4. Aim the camera in the appropriate direction for the given lighting condition
and press the center of the control wheel. See the ExpoDisc Instruction
Manual for more information on where to aim the camera.
5. After the shutter sound beeps, the calibrated values (ColorTemperature and
Color filter) are displayed.
6. Select a registration number (1-3) using the right/left button. The monitor
returns to the recording information display retaining the memorized custom
white balance setting.
7. If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
8. From the White Balance menu, select the Custom 1 / Custom 2 / Custom 3
depending on where you saved the measurement in step 6.
9. Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony A33/A55
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. Press the WB (White Balance) on the control button to display the White
Balance mode screen.
4. Select (SET) with the !/"on the control button, then press the center of
the control button.
5. Aim the camera in the appropriate direction for the given lighting condition
and press the shutter release button. See the ExpoDisc Instruction Manual for
more information on where to aim the camera.
6. The shutter clicks and the calibrated values (ColorTemperature and Color
filter) are displayed.
7. Press the center of the control button again. The monitor returns to the
Copyright, 2020 ExpoImaging, Inc.
“Sony” and the Sony camera models listed are trademarks of Sony, Inc.
recording information display with the memorized white balance retained.
The custom white balance setting registered in this operation is effective until
a new setting is registered.
8. If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
9. Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony A77
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. Press the WB (White Balance) button > Select (SET) > Press the center of
the Multi-Selector.
4. Aim the camera in the appropriate direction for the given lighting condition
and press the shutter release button. See the ExpoDisc Instruction Manual for
more information on where to aim the camera.
5. The shutter clicks and the calibrated values (ColorTemperature and Color
filter) are displayed.
6. Select a register using the multi-selector, then press the center of the multi-
selector. The A77 allows you to set and save 3 custom white balance
settings.
7. The monitor returns to the recording information display with the memorized
white balance setting retained. The custom white balance setting registered
in this operation is effective until a new setting is registered.
8. If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
9. Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony A100
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. Rotate the function dial on the top-left of the camera to the WB position.
4. Press the Fn button in the center of the function dial to display the White-
Balance mode screen.
5. Using the controller pad to the right of the screen, move up or down to select
the custom white balance icon () and press on the controller pad.
6. Select (set) by pressing on the controller. Press the center button on
the controller. “Use spot metering area. Press shutter to calibrate.” will
appear on the screen.
Copyright, 2020 ExpoImaging, Inc.
“Sony” and the Sony camera models listed are trademarks of Sony, Inc.
7. Aim the camera in the appropriate direction for the given lighting condition
and press the shutter release button. See the ExpoDisc Instruction Manual for
more information on where to aim the camera. The screen will display color
temperature values.
8. Press the center button on the controller to store the white balance recorded.
9. Remove the ExpoDisc, place camera in desired shooting mode and start
shooting.
Sony A200 / A300 / A350
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. Press the Fn button to select the White Balance icon ().
4. Select (SET) with the !/"on the controller.
5. Aim the camera in the appropriate direction for the given lighting condition
and press the shutter release button. See the ExpoDisc Instruction Manual for
more information on where to aim the camera.
6. Press the center of the controller. The monitor returns to the recording
information display with the memorized custom white balance setting
retained. This white balance setting will stay in effect until a new custom
white balance is registered.
7. If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
8. Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony A700
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. Press the WB (White Balance) Button to display the White Balance mode
screen.
4. Select a custom white balance item () using the #/$on the multi-selector.
5. Select (SET), then press the center of the multi-selector to display the
register screen.
6. The message “Use spot metering area. Press shutter to calibrate.” will
appear on the screen.
7. Aim the camera in the appropriate direction for the given lighting condition
and press the shutter release button. See the ExpoDisc Instruction Manual for
more information on where to aim the camera.
8. The register selection screen appears. Select a memory number with !/"
(1), then press the center of the multi-selector. The Sony A700 allows you
Copyright, 2020 ExpoImaging, Inc.
“Sony” and the Sony camera models listed are trademarks of Sony, Inc.
to save up to 3 custom white balance references. This white balance setting
will stay in effect until a new custom white balance is registered under the
same memory number.
9. Make sure that the number you registered (ie 1), is the same white
balance that you are set to on the White Balance mode screen.
10.If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
11. Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony A900
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. Press the WB (White Balance) Button to display the White Balance mode
screen.
4. Select a custom white balance item (*) using the !/"on the multi-
selector, then press the center of the multi-selector.
5. Select (SET) with the !/"on the multi-selector, then press the center of
the multi-selector.
6. Aim the camera in the appropriate direction for the given lighting condition
and press the shutter release button. See the ExpoDisc Instruction Manual for
more information on where to aim the camera.
7. The shutter clicks and the calibrated values (ColorTemperature and Color
filter) are displayed.
8. Select a memory number with !/"(1), then press the center of the multi-
selector. The Sony A900 allows you to save up to 3 custom white balance
references. This white balance setting will stay in effect until a new custom
white balance is registered under the same memory number.
9. Make sure that the number you registered (ie. 1), is the same white
balance that you are set to on the White Balance mode screen.
10.If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
11. Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony A6400
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. From the MENU navigate to the Camera Settings1 screen and select White
Balance and then select [from Custom1] to [Custom 3], and then press the
Copyright, 2020 ExpoImaging, Inc.
“Sony” and the Sony camera models listed are trademarks of Sony, Inc.
right side of the control wheel.
4. Select (SET), and then press the center of the control wheel.
5. Aim the camera in the appropriate direction for the given lighting condition
and press the center of the control wheel. See the ExpoDisc Instruction
Manual for more information on where to aim the camera.
6. After the shutter sound beeps, the calibrated values (ColorTemperature and
Color filter) are displayed and registered.
7. Press the center of the control wheel. The monitor returns to the recording
information display with the memorized white balance retained. The custom
white balance setting registered in this operation is effective until a new
setting is registered.
8. If you get the message “Custom WB error” this indicates that you need to
adjust your exposure and reattempt to set your white balance.
9. From the White Balance menu, select (Custom 1, 2, or 3 depending on
where you set the white balance measurement).
10.Remove the ExpoDisc, return the camera to auto focus if desired and start
shooting.
Sony DSC-F828
1. Install the ExpoDisc and set the camera to Manual Focus mode.
2. Allow the camera to set an automatic exposure using the “P”, “S” or “A”
modes or set the correct manual exposure in “M” mode.
3. Set your camera to the Standard Color mode. Press Menu. When the menu
appears, use the Multi-Selector to select Color and then select Standard.
4. Press and hold the WB Button and select the WB Set setting with the
Command Dial. The WB Set indicator appears in the LCD monitor.
5. Aim the camera in the appropriate direction for the given lighting condition
and press the shutter release button. See the ExpoDisc Instruction Manual for
more information on where to aim the camera.
6. Press the center of the Multi-Selector. The screen momentarily turns black
and the WB Set indicator flashes quickly. DO NOT SHAKE OR STRIKE THE
CAMERA WHILE THE WB INDICATOR IS FLASHING QUICKLY.
7. When the custom white balance has been adjusted and stored in memory, the
WB indicator lights up.
8. If the WB indicator flashes slowly, the white balance is not set or was not able
to be set. In this case, adjust the exposure settings and recalibrate.
9. Remove the ExpoDisc, place camera in desired shooting mode and start
shooting.
Copyright, 2020 ExpoImaging, Inc.
“Sony” and the Sony camera models listed are trademarks of Sony, Inc.
Autres manuels pour A 7 R IV
1
Ce manuel convient aux modèles suivants
13
Table des matières
Autres manuels Sony Appareil photo numérique
Sony
Sony Cyber-Shot DSC-J10 Manuel utilisateur
Sony
Sony Cyber-shot DSC-S600 Manuel utilisateur
Sony
Sony DSC-TX7 - Cyber-shot Digital Still Camera Manuel utilisateur
Sony
Sony Cyber-shot DSC-HX20V Manuel utilisateur
Sony
Sony cyber-shot DSC-570 Manuel utilisateur
Sony
Sony Cyber-shot DSC-S600 Manuel utilisateur
Sony
Sony FCB-EV7100 Manuel utilisateur
Sony
Sony Cyber-shot DSC-S600 Manuel utilisateur
Sony
Sony EXPODISC A200 Fiche technique
Sony
Sony Cyber-shot DSC-WX70 Manuel utilisateur
Sony
Sony DSC-N1 Manuel utilisateur
Sony
Sony Mavica MVC-FD83 Manuel utilisateur
Sony
Sony Cyber-shot DSC-W670 Manuel utilisateur
Sony
Sony DSC-W350 Cyber-shot® Manuel utilisateur
Sony
Sony DSC-P7 - Cyber-shot Digital Still Camera Manuel utilisateur
Sony
Sony DSC-W830 Guide de référence
Sony
Sony Cyber-shot DSC-W800 Manuel utilisateur
Sony
Sony Cyber-shot DSC-TX200 Manuel utilisateur
Sony
Sony ILCE-9 Manuel utilisateur
Sony
Sony Cyber-Shot DSC-KW11 Guide de l'utilisateur
