Sony SAL55200-2 Manuel utilisateur

SERVICE NOTE

SPECIFICATIONS

REPAIR PARTS LIST

DISASSEMBLY ADJUSTMENTS

SERVICE MANUAL

Link (English)

Revision History

Sony EMCS Co.

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

SERVICE NOTE

SPECIFICATIONS

REPAIR PARTS LIST

DISASSEMBLY ADJUSTMENTS

Link (Japanese)

Link (English)

Link (Japanese)

Ver. 1.0 2009.04

LENS FOR DSLR CAMERA

2009D0800-1

Published by Kohda TEC9-852-692-11

US Model

Canadian Model

AEP Model

Chinese Model

Japanese Model

SAL55200-2

(DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

• About the Lens Test Projector and Finished Inspection JIG II

・レンズ投影器と完成検査治具

について

分解図につきましては，英語版を

ご参照ください。

— 2 —

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

SPECIFICATIONS

• This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using a flash for ADI.

•Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is focused

at infinity.

Equivalent 35mm-format focal length *1(mm)

82.5-300

Lens groups elements

9-13

Angle of view *1

29°-8°

*1The values for equivalent 35mm-format focal length and angle of view are based on Digital Single Lens Reflex Cameras equipped with an APS-

C sized image sensor.

Minimum focus *2(m (feet))

0.95 (3.2)

*2Minimum focus is the shortest distance from the image sensor to the subject.

Maximum magnification (X)

0.29

Minimum f-stop

f/32-45

Filter diameter (mm)

Dimensions (maximum diameter ××

××

×height) (mm (in.))

Approx. 71.5 ×85 (2 7/8 ×3 3/8)

Mass (g (oz.))

Approx. 305 (10 3/4)

Included items

Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Set of printed documentation

Designs and specifications are subject to change without notice.

1st Lens

(33.478mm)

2nd Lens

(8.353mm)

3rd Lens

(11.243mm)

Extra-Low Dispersion Glass

WIDE

TELE

1-1

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

1. SERVICE NOTE

1-1. Chemicals

Some chemicals used for servicing are highly volatile.

Their evaporation caused by improper management affects your health and environment, and wastes resources.

Manage the chemicals carefully as follows.

• Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.

• Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.

• Keep containers sealed to avoid natural evaporation when chemicals are not in use.

• Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and

use up it.

1-2. Exterior Parts

Be careful to the following points for exterior parts used in this unit.

• Use a piece of cleaning paper or cleaning cloth for cleaning exterior parts. Avoid using chemicals.

Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.

• Insert the specific screws vertically to the part when installing a exterior part.

Be careful not to tighten screws too much.

1-3. Unleaded Solder

This unit uses unleaded solder.

Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Be careful to the following points to solder or unsolder.

• Set the soldering iron tip temperature to 350 °C approximately.

If cannot control temperature, solder/unsolder at high temperature for a short time.

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

• Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing

unleaded solder and leaded solder will cause detachment phenomenon.

1-2

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

1-4. SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and

bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the

customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their

replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 °C during repairing.

• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering or unsoldering.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH

MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

2-1

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

2. DISASSEMBLY

Cut and remove the part of gilt

which comes off at the point.

(Be careful or some

pieces of gilt may be left inside)

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, don’t press down at wire of connector.

It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

UNIVERSAL WRENCH

In case of the following notches or holes are located in the lens block, etc during disassembling/

assembling the lens, Use the universal wrench.

How to Use

Attach the chip-A or chip-B to the universal wrench.

For the notches: chip-A

For the holes: chip-B

Match the universal wrench to the holes or notches of the lens block, etc.

Notches Holes

Universal wrench

J-6082-609-A

Chip-A for

universal wrench:

J-6082-609-1

Chip-B for

universal wrench:

J-6082-609-2

Notches

Chip-A

Chip-B

Chip

Fixed screw

Chip

Match the universal wrench

to the width of holes or notches.

Universal wrench

Holes

SERVICE TOOLS

Grease (G-32): J-6082-666-A

Grease (G-22): J-6082-665-A

Grease (G-36): J-6082-667-A

Adhesive bond (LOCTITE 460)

or the equivalent.

G-32

G-22

LOCTITE 460

or the equivalent

G-36

B-10

Adhesive bond (B-10): J-6082-612-A

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

2-2

2-1. DISASSEMBLY

REPAIR PARTS LIST

G-32

G-22 G-36

G-32

q; 6

B-10 B-10

B-10

HELP01

HELP02

HELP03

HELP04

HELP05

2-1-1

2-1-2

6U2.6X2.5C3C

LOCTITE 460

or the equivalent

Note 1:

This lens can disassemble both the

1st lens side and the mount side.

Rear Light Shield Barrel

Mount Assy

Back Adjustment Washer

Rear Barrel Assy

Function Lever

AF/MF Switch Block

(Note 2)

Gear Assy

Chip

(Mount Index)

Main PCB Assy

Idler Shaft

Idler B

Zoom Brush

Brush Connect

Plate

Zoom Rubber Ring

Zoom Linkage Plate

Zoom Ring

Decoration Seal

Focus Rubber Ring

First Lens Barrel Assy

1st Lens Adjustment Washer

Light Shield Plate

2nd Lens Decoration Plate

Semi Barrel Assy

Focus Brush

G11-13 Lens Barrel Assy

G10-11 Adjustment Washer

Three Screws

FOCUS BRUSH POSITION

ADJUSTMENT

FLANGE BACK

ADJUSTMENT (WIDE)

APERTURE

DIAMETER

ADJUSTMENT

ZOOM BRUSH POSITION

ADJUSTMENT

PROJECTIVE RESOLVING POWER

(PARTIAL BLUR) ADJUSTMENT

FLANGE BACK

ADJUSTMENT (TELE)

PROJECTIVE RESOLVING

POWER (CURVATURE OF

FIELD) ADJUSTMENT

OPTICAL AXIS ADJUSTMENT

Note 2:

How to remove the AF/MF switch block (Scratch prevention)

1. Remove two screws fixing the AF/MF switch block.

2. Push out two screw installation parts from the inside and

remove the AF/MF switch.

HELP

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

HELP

Note for assembling and grease applying positions are shown.

HELP01

1. Install the back adjustment washer to the main assy.

2. Set the main assy so that it becomes in the WIDE state.

3. Put the function lever of the mount assy in the groove of aperture driving wheel, install the mount assy while releasing the main

spring outward and tighten it with four mount fix screws.

Note: House the main spring of the mount assy in the gear assy and assemble it.

Install the mount assy so that the main spring of the mount assy does not conflict with the zoom brush

Back Adjustment Washer

Main Assy

Function Lever

Main Spring

Mount Assy

Mount Fix Screw

Groove of Aperture

Driving Wheel

HELP

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

HELP02

How to remove the switch panel block (Scratch prevention)

1. Remove two screws fixing the AF/MF switch block.

2. Push out two screw installation parts from the inside and remove the AF/MF switch.

Note on switch panel installation

1. Set the slide switch of gear assy to AF.

2. Set the knob of AF/MF switch block to AF.

3. Install the AF/MF switch block with two screws.

HELP03

Adhesive bond (LOCTITE 460)

Note: Use the adhesive bond (LOCTITE 460) or an equivalent article.

Do not use what becomes white after drying like quick-drying glue.

1. Apply the adhesive bond (LOCTITE 460) to the affixing side of mount index of rear barrel assy and affix the mount index.

Slide Switch

(Gear Assy)

AF/MF Switch Block

Knob

Rear Barrel Assy

LOCTITE 460 or the equivalent

Chip (Mount Index)

Screw installation part

HELP

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

HELP04

Grease (G-22): J-6082-665-A

Grease (G-36): J-6082-667-A

1. Apply the grease (G-22) to the gear C, idler shaft and idler B.

2. Apply the grease (G-36) to the indicated portion of gear assy.

3. When connecting the connector, route the lead wires as shown below.

Idler B

Apply the grease (G-22)

Apply the grease (G-36)

Gear Assy

Idler Shaft

Gear C

Main PCB Assy

Red lead wire

Connector Black lead wire

HELP

SAL55200-2 (DT 4-5.6/55-200 SAM) (DT 55-200mm F4-5.6 SAM)

HELP05

Grease (G-32): J-6082-666-A

1. Apply the grease (G-32) to the middle barrel and the inner bayonet portions of zoom ring.

2. Assemble the zoom ring, aligning the projections of zoom ring with the grooves of main assy.

3. Apply the grease (G-32) to the indicated portion of zoom linkage plate.

4. Align the screw holes on the side of zoom ring (hole for fixing the screw of zoom linkage plate) with the installation positions of the

zoom linkage plate by rotating the zoom ring and fix it with two screws.

Note: Set the zoom to the WIDE end and install the zoom linkage plate.

Middle Barrel

Installation position

(Zoom Linkage Plate)

Main Assy

(WIDE)

Apply the grease (G-32)

Zoom Linkage Plate

Zoom Ring

Main Assy

Bayonet Portion

Two Screws

Zoom Ring

Groove Projection

Groove

Projection

Autres manuels pour SAL55200-2

Table des matières

Autres manuels Sony Objectif de l'appareil photo

Sony

Sony NEX-3D - alpha; Nex-3 With Sel-16f28 Manuel utilisateur

Sony

Sony SAL1118 - DT 11-18mm f/4.5-5.6 Aspherical ED Super Wide Angle Zoom... Manuel utilisateur

Sony

Sony SAL2470Z Manuel utilisateur

Sony

Sony Alpha SAL1650 Manuel utilisateur

Sony

Sony VF-25CPKS Manuel utilisateur

Sony

Sony VF-520K Manuel utilisateur

Sony

Sony VCL-HG0862 Manuel utilisateur

Sony

Sony VCL-HGE08B Manuel utilisateur

Sony

Sony SEL-24F18Z Manuel utilisateur

Sony

Sony SAL-24105 Manuel utilisateur

Sony

Sony DH1730 Manuel utilisateur

Sony

Sony SAL16F28 Manuel utilisateur

Sony

Sony SAL18250 - Zoom Lens - 18 mm Manuel utilisateur

Sony

Sony VCL-DH1730 Manuel utilisateur

Sony

Sony SEL-30M35 Manuel utilisateur

Sony

Sony VCL-716BX Manuel utilisateur

Sony

Sony SLT-A33 Manuel utilisateur

Sony

Sony SAL100M28 - Macro Lens - 100 mm Manuel d'instructions d'installation

Sony

Sony VCL-718BX Manuel utilisateur

Sony

Sony NEX-VG10 - Digital Hd Video Camera Recorder Mode d’emploi

Sony

Sony VCL-2030S Manuel utilisateur

Sony

Sony SAL14TC - 1.4x Teleconverter Lens Manuel utilisateur

Sony

Sony SAL16105 - Zoom Lens - 16 mm Manuel utilisateur

Sony

Sony SEL-18200 Manuel d'instructions d'installation

Manuels Objectif de l'appareil photo populaires d'autres marques

THORLABS

THORLABS ELL15 Manuel utilisateur

FUJICA

FUJICA ZC1000 Manuel utilisateur

Tamron

Tamron A09 Manuel

Honeywell

Honeywell HLM25V6F12 Manuel utilisateur

Canon

Canon FD 35 - 70 mm Manuel utilisateur

ARRI

ARRI Lenses Manuel utilisateur

Panasonic

Panasonic LUMIX G X Vario 45-175mm f/4.0-5.6 Manuel utilisateur

Nikon

Nikon AF-S VR 24-120 f/3.5-5.6G IF-ED Manuel utilisateur

Rokinon

Rokinon DS50M-C Manuel utilisateur

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Manuel utilisateur

Canon

Canon FD Lens Manuel

Tamron

Tamron A036 Manuel utilisateur

Samsung

Samsung 20-50mm F3.5-5.6 ED II Manuel utilisateur

Tamron

Tamron 272E Manuel utilisateur

Sinar

Sinar Rolleiflex 6008 AF Manuel utilisateur

Rokinon

Rokinon SP 85mm F1.2 Manuel utilisateur

Nikon

Nikon AF-S Zoom-Nikkor 17-35mm f/2.8D IF-ED Manuel utilisateur

Samsung

Samsung Samsung 18-55mm Manuel utilisateur