Sony SAL1118 - DT 11-18mm f/4.5-5.6 Aspherical ED Super Wide Angle Zoom... Manuel utilisateur

SERVICE NOTE

SPECIFICATIONS

REPAIR PARTS LIST

DISASSEMBLY ADJUSTMENTS

SERVICE MANUAL

Link

Revision History

How to use

Acrobat Reader

How to use

Acrobat Reader

Sony EMCS Co.

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

Ver 1.3 2007.04

LENS FOR DSLR CAMERA

2007D0800-1

Published by KohdaTEC9-852-104-12

US Model

Canadian Model

AEP Model

Chinese Model

SAL1118

(4.5-5.6/11-18) (DT 11-18mm F4.5-5.5)

• About the Lens Test Projector

— 2 —

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

SPECIFICATIONS

• This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using a flash for ADI.

• Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is focused

at infinity.

Equivalent 35mm-format focal length*1(mm)

16.5-27

Lens groups elements

12-15

Angle of view*1

104°-76°

*1The values for equivalent 35mm-format focal length and angle of view are based on Digital Single Lens Reflex Cameras equipped with an APS-

C sized image sensor.

Minimum focus*2(m (feet))

0.25 (0.8)

*2Minimum focus is the shortest distance from the image sensor to the subject.

Maximum magnification (X)

0.125

Minimum f-stop

f/22-29

Filter diameter (mm)

Dimensions (maximum diameter ××

××

×height) (mm (in.))

Approx. 83 ×80.5 (3 3/8 ×3 1/4)

Mass (g (oz.))

Approx. 360 (12 11/16)

Included items

Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Set of printed documentation

Designs and specifications are subject to change without notice.

—3 —

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

TABLE OF CONTENTS

Section Title Page

1. SERVICE NOTE

1-1. Chemicals ·······································································1-1

1-2. Exterior Parts··································································1-1

1-3. Unleaded Solder ·····························································1-1

1-4. Safety check-out·····························································1-2

1-5. Troubleshooting ·····························································1-3

2. DISASSEMBLY

2-1. Disassembly ···································································2-2

3. REPAIR PARTS LIST

3-1. Exploded Views ······························································3-1

3-2. Supplied Accessories······················································3-4

4. ADJUSTMENTS

4-1. Preparations····································································4-1

4-2. Aperture Diameter Check/Adjustment···························4-4

4-3. Projective Resolving Power Check ································4-8

4-4. Focus-Shift/Flange Back (f’F) and

Optical Axis Check/Adjustment···································4-12

4-5. Lens ROM Check·························································4-17

4-6. Zoom Brush Position Check/Adjustment and

Pattern Check ·······························································4-18

4-7. Focus Brush Position and Pattern Check ·····················4-20

4-8. Error Code List·····························································4-22

1-1

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

1. SERVICE NOTE

1-1. Chemicals

Some chemicals used for servicing are highly volatile.

Their evaporation caused by improper management affects your health and environment, and wastes resources.

Manage the chemicals carefully as follows.

•Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.

•Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.

•Keep containers sealed to avoid natural evaporation when chemicals are not in use.

•Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and

use up it.

1-2. Exterior Parts

Be careful to the following points for exterior parts used in this unit.

•Use a piece of cleaning paper or cleaning cloth for cleaning exterior parts.Avoid using chemicals.

Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.

•Insert the specific screws vertically to the part when installing a exterior part.

Be careful not to tighten screws too much.

1-3. Unleaded Solder

This unit uses unleaded solder.

Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

: LEAD FREE MARK

Be careful to the following points to solder or unsolder.

•Set the soldering iron tip temperature to 350 °C approximately.

If cannot control temperature, solder/unsolder at high temperature for a short time.

Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!

Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

•Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing

unleaded solder and leaded solder will cause detachment phenomenon.

1-2

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

1-4. SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and

bridges.

2. Check the interboard wiring to ensure that no wires are “pinched”or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the

customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their

replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270 °C during repairing.

•Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).

•Be careful not to apply force on the conductor when soldering or unsoldering.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH

MARK 0ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

CAUTION

Dangerofexplosionif batteryisincorrectly replaced.

Replace only with the same or equivalent type.

1-3

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

1-5. TROUBLESHOOTING

1-5-1. ApertureTrouble

Check operation of

the preset ring.

Replace the mount assy.

Perform the aperture

diameter adjustment.

(See page 4-7.)

Perform the aperture

diameter check.

(See page 4-4.)

Check operation

of the diaphragm.

OK OK

Function NG F No. NG

Aperture trouble

Replace the lens assy

with diaphragm.

NGNG

END

Perform the aperture

diameter check.

(See page 4-4.)

1-4

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

1-5-2. ZoomTrouble

Function NG Position NG

Check the position

and deformation

at the tip of

the zoom brush.

Adjust the position, or

replace the zoom brush.

Check board pattern

of the zoom flex pattern.

Clean the board pattern

zoom flex pattern.

Zoom trouble

Replace the main pcb

assy.

Perform the

zoom brush position

check/adjustment.

(See page 4-17.)

END

Disassembly and check

the zoom relation parts.

Replace the defective part

or apply the grease.

Check the operation

again.

1-5

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

1-5-3. FocusTrouble

Check the operation

again.

Replace the defective part

or apply the grease.

Function NG Position NG

Focus trouble

Replace the defective part

or apply the grease.

Check the coupler and

gear shaft of the rear

lens barrel assy.

Check the focus gear

barrel and

focus coupling barrel.

NGNG

END

Check the position

and deformation

at the tip of

the focus brush.

Check the position, or

replace the focus brush.

Check board pattern

of the focus flex pattern.

Clean the board pattern.

Replace the main pcb

assy.

Perform the

focus brush position

check/pattern check.

(See page 4-19.)

2-1

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

2. DISASSEMBLY

Cut and remove the part of gilt

which comes off at the point.

(Be careful or some

pieces of gilt may be left inside)

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, dont’pull at wire of connector.It is possible that a wire is snapped.

• When installing a connector, dont’press down at wire of connector.

It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

UNIVERSALWRENCH

In case of the following notches or holes are located in the lens block, etc during disassembling/

assembling the lens, Use the universal wrench.

How to Use

Attach the chip-A or chip-B to the universal wrench.

For the notches: chip-A

For the holes: chip-B

Match the universal wrench to the holes or notches of the lens block, etc.

Notches Holes

Universal wrench

J-6082-609-A

Chip-A for

universal wrench:

J-6082-609-1

Chip-B for

universal wrench:

J-6082-609-2

Notches

Chip-A

Chip-B

Chip

Match the universal wrench

to the width of holes or notches. Universal wrench

Holes

2-2

SAL1118 (4.5-5.6/11-18) (DT 11-18mm F4.5-5.6)

2-1. DISASSEMBLY

2-1-1. REAR LIGHT SHIELD BARREL, MOUNT SET AND REAR LENS BARREL ASSY

HELP01

HELP02

HELP03

HELP08

HELP06

HELP05

HELP04

HELP07

EXPLODEDVIEW

(See Page 2-3.)

Focus Rubber

Rear Lens Barrel Assy

Gear Base Plate Assy

Decorating Ring

1st Lens Barrel Assy

Filter Screw Frame

Main PCB Assy

Zoom Rubber

Rear Light

Shield Barrel

Mount Assy

Back Adjustment Washer (T=0.03mm)

FLANGE BACK (f F) ADJUSTMENT

FOCUS-SHIFT ADJUSTMENT

APERTURE

DIAMETER

ADJUSTMENT

ZOOM BRUSH POSITION ADJUSTMENT/

PATTERN CHECK

Autres manuels pour SAL1118 - DT 11-18mm f/4.5-5.6 Aspherical ED Super Wide Angle Zoom...

Table des matières

Autres manuels Sony Objectif de l'appareil photo

Sony

Sony SAL16105 - Zoom Lens - 16 mm Manuel utilisateur

Sony

Sony SEL90M28G Manuel utilisateur

Sony

Sony VCL-HG1737C Manuel utilisateur

Sony

Sony VCL-DH0758 Manuel utilisateur

Sony

Sony VCL-HG0872X Manuel utilisateur

Sony

Sony SEL-30M35 Manuel utilisateur

Sony

Sony SELP1020G Manuel utilisateur

Sony

Sony SEL-55210 Manuel utilisateur

Sony

Sony VCL-HG0737Y Manuel utilisateur

Sony

Sony SEL90M28G Manuel utilisateur

Sony

Sony SEL-24F18Z Manuel utilisateur

Sony

Sony VCL-HG2025 Manuel utilisateur

Sony

Sony VCL-HG2025 Manuel utilisateur

Sony

Sony SAL-35F18 Manuel utilisateur

Sony

Sony Vario-Sonnar T DT 16-BOmm F3.5-4.5 ZA Manuel utilisateur

Sony

Sony E 15mm F1.4 G Manuel utilisateur

Sony

Sony DSLRA100H - Alpha A100H 10.2MP Digital SLR... Manuel utilisateur

Sony

Sony VCL-0716BXA Manuel utilisateur

Sony

Sony FE 20mm F1.8 G Manuel utilisateur

Sony

Sony SAL55200-2 Manuel utilisateur

Sony

Sony SAL2470Z Manuel utilisateur

Sony

Sony Alpha SEL35F18 Manuel utilisateur

Sony

Sony SEL1224G Manuel utilisateur

Sony

Sony VCL-HG0737Y Manuel utilisateur

Manuels Objectif de l'appareil photo populaires d'autres marques

THORLABS

THORLABS ELL15 Manuel utilisateur

FUJICA

FUJICA ZC1000 Manuel utilisateur

Tamron

Tamron A09 Manuel

Honeywell

Honeywell HLM25V6F12 Manuel utilisateur

Canon

Canon FD 35 - 70 mm Manuel utilisateur

ARRI

ARRI Lenses Manuel utilisateur

Panasonic

Panasonic LUMIX G X Vario 45-175mm f/4.0-5.6 Manuel utilisateur

Nikon

Nikon AF-S VR 24-120 f/3.5-5.6G IF-ED Manuel utilisateur

Rokinon

Rokinon DS50M-C Manuel utilisateur

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Manuel utilisateur

Canon

Canon FD Lens Manuel

Tamron

Tamron A036 Manuel utilisateur

Samsung

Samsung 20-50mm F3.5-5.6 ED II Manuel utilisateur

Tamron

Tamron 272E Manuel utilisateur

Sinar

Sinar Rolleiflex 6008 AF Manuel utilisateur

Rokinon

Rokinon SP 85mm F1.2 Manuel utilisateur

Nikon

Nikon AF-S Zoom-Nikkor 17-35mm f/2.8D IF-ED Manuel utilisateur

Samsung

Samsung Samsung 18-55mm Manuel utilisateur