Sony F519R Manuel utilisateur

SERVICE MANUAL AEP Mode!

Photo :TA-F519R

SPECIFICATIONS

Amplifier

Continuous RMS power output (both channels driven

simultaneously)

Model for Germany

TA-F519R TA-F419R

DIN, 1kHz 4ohms 105W+ 105 W80 W+80 W

8ohms 85 W+85 W75 W+75 W

20 Hz -20

kHz ;

4ohms 80 W+80 W75 W+75 W

8ohms 75 W+75 W65 W+65 W

Model for Scandinavian countries, Switzerland, Spain and Portugal

TA-F519R TA-F419R

DIN, 1kHz 6ohms 100 W+ 100 w80 W+80 W

8ohms 80 W+80 W70 W+70 W

20 Hz-20

kHz 6ohms 75 W-f 75 W70 W+70 W

8ohms 70 W+70 W60 W+60 W

Mode! for other countries

TA-F519R TA-F419R

DIN, 1kHz 4ohms 105 W+ 105 W80 W+80 W

8ohms 85 W+85 W75 W+75 W

20 Hz -20

kHz 4ohms 80W +80W 75 W+75 W

8ohms 75 W+75 W65 W+65 W

Input

Input jack Jack type Sensitivity impedance

PHONO (MM) Phono 2.0 mV 50 kilohms

PHONO (MC) Phono 0.17 mV 100 ohms

TUNER, CD, AUX,

DAT/TAPE 1

TAPE 2

Phono 150 mV 50 kilohms

PHONO (MM/MC): only for TA-F519R

S/N

TA-F519R TA-F419R

PHONO (MM) 76 dB —

PHONO (MC) 94 dB 94 dB

TUNER, CD, AUX,

DAT/TAPE 1

TAPE 2

103 dB 103 dB

Output

Output jack Jack type Voltage/impedance

REC OUT Phono jack Voltage 150 mV impedance 1

kohm

HEADPHONES Stereo phono

jack

Accepts low and high

impedance headphones

INTEGRATED STEREO AMPLIFIER

TA-F419R/F519R

Tone controls

Response :-,5

Turnover frequency

BASS ,... y* -«<»*. -±7 dB (100 Hz) 300 Hz

treble' ±6 dB (10 kHz) 5kHz

Harmonic distortion Less than 0.008% at 10 Woutput

Intermodulation (IM) distortion (60 Hz :7kHz =4:1)

Less than 0.008% at 10 Woutput

Frequency response PHONO: RIAA equalization curve

±0.5 dB

TUNER, CD, AUX, DATyTAPE 1,

TAPE 2: 7Hz- 100 kHz^dB

Residual noise Less than 170 pV (network A)

Damping factor 70 (8 ohms, 1kHz)

General

System

Power requirements

Power consumption

Dimensions

Weight

Supplied accessories

Preamplifier: Low-noise, equalizer

amplifier

Power amplifier: Pure-complementary

SEPP OCL power amplifier with all

stages directly coupled

220 V-230 VAC, 50/60 Hz

Model for Germany

TA-F519R: 160 W

TA-F419R: 160W

Model for Scandinavian countries,

Switzerland, Spain and Portugal

TA-F519R: 160 W

TA-F419R: 160 W

Model for other European countries

TA-F 51 9R: 260 W

TA-F419R: 260 W

Approx. 430 x150 x375 mm (w/h/d)

(17 x57/8x14 3/4inches)

TA-F519R: Approx. 9.1 kg (20 lb 1oz)

TA-F419R: Approx. 8.6 kg (18 lb 15 oz)

Remote commander RM-S31 1(1)

Sony SUM-3 (NS) batteries (2)

The above values are measured at 230 VAC. (Models for European

countries)

Design and specifications are subject to change without notice.

Note

This appliance conforms with EEC Directive 87/308/EEC regarding

interference suppression.

TABLE OF CONTENTS

Section Title Page

Specifications 1

1.GENERAL 3

2. ELECTRICAL ADJUSTMENTS 4

3. DIAGRAMS

3-1. Circuit Boards Location 4

3-2. Block Diagram 5

3-3. Printed Wiring Boards (KEY BOARD SECTION) 8

3-4. Printed Wiring Boards (MAIN BOARD SECTION) -11

3-5. Schematic Diagram 15

6. IC Block Diagram 19

4. EXPLODED VIEWS

1.Front Panel Section 20

4-2. Chassis Section- 121

4-3. Chassis Section-2 22

5. ELECTRICAL PARTS LIST 23

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK AOR DOTTED LINE

WITH MARK AON THE SCHEMATIC DIAGRAMS AND IN

THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.

REPLACE THESE COMPONENTS WITH SONY PARTS

WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS

MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

SECTION 1

GENERAL

Identifying the

Parts and Controls

This section describes about each name of

this amplifier and remote commander.

This section is extracted from

instruction manual.

Front Panel

CD POWER switch and STANDBY indicator

HI Remote control sensor

mFunction selectors and indicators

El SOURCE DIRECT button and indicator

[5] VOLUME control and indicator

Adjusts the sound level.

Immediately after turning on the

POWER switch ,the VOLUME indicator

blinks when the built-in muting circuit

activates and the unit detects shorting

of circuit of the speaker outputs or in

case of short-circuit of the inputs of DC

components. In such case, turn off the

unit and check the connected

components and speaker system.

HI HEADPHONES jack

mSPEAKERS selector

mTONE (BASS/TREBLE) controls

®REC OUT SELECTOR

HBALANCE control

El SUBSONIC switch (TA-F519R)

HCARTRIDGE selector (TA-F519R)

Remote Commaner

CD POWER switch

HI TUNER operation buttons

TUNER: Select the TUNER mode.

PRESET +/- buttons: Select the

preset station.

HO CD operation buttons

*«*/** Automatic music sensor.

D. (Disc) SKIP: Disc skip (for CD

player equipped with amulti-disc

changer)

:The amplifier enters the CD mode

and the CD player starts playback

automatically.

:Stop,

ii: Pause.

0TAPE 2DECK A/DECK Boperation

buttons

Fast winding.

:Stop.

:The amplifier enters the TAPE 2

mode and the tape deck starts

reverse playback automatically.

:The amplifier enters the TAPE 2

mode and the tape deck starts

forward playback automatically.

•: Recording.

II: Pause. (Only for DECK B)

HI VOL (Volume) +/- buttons

H3 PHONO operation buttons

START: Pressing START

automatically selects the PHONO

mode on the amplifier and starts

playback of the turntable system.

STOP: Stops playback of the

turntable system.

mDAT/TAPE tbutton

Selects the DAT or TAPE 1mode.

HD AUX button

Selects the AUX mode.

SECTION 2

ELECTRICAL ADJUSTMENTS

Note :

1. DC BIAS adjustments should be made one minute after

the POWER switch is turned on (POWER ON).

2. After replacing the power transistors, DC BAIS

adjustments should be made.

DC Bias Adjustment (with no signal input)

Procedure :

MAIN BOARD

TP (L-CH) VTVM

TP (R-CH)

Adjustment Location :

[MAIN BOARD]

-COMPONENT SIDE -

TP (L-CH) TP (R-CH)

3-2. BLOCK DIAGRAM

•IC700 System Controller (M50720-358SP)

Pin No. Pin Name I/O Description

15V CHECK IPower supply (+5V) check.

2S/D ON/OFF ISource direct ON/OFF control input.

3PROTECT IProtection signal input.

4XOUT 0Connected oscillator circuit.

5XIN IConnected oscillator circuit.

6CE ISignal input for areturn to normal position.

7RESET IReset signal input. (”L” :RESET)

8VDD I-f5Volts power supply.

9CNTR IGround.

10 AC DET IAC power supply detection input.

11 CIConnected O.l^F capacitor.

12 VOL UP o Volume control (up) signal output.

13 VOL DOWN 0Volume control (down) signal output.

14 MOTOR NORM 0Motor (normal turn) signal output.

15 MOTOR RVS 0Motor (reverse turn) signal output.

16 SIRCS IN ISerial data input (SIRCS).

17 SI IFunction selector positioning detection input (PHONO).

18 S2 IFunction selector positioning detection input (TUNER).

19 S3 IFunction selector positioning detection input (CD).

20 CNVSS —Ground.

21 VSS —Ground.

22 S4 IFunction selector positioning detection input (AUX).

23 S5 IFunction selector positioning detection input (TAPE 1).

24 S6 IFunction selector positioning detection input (TAPE 2).

25 ;S7 IConnected the resistor 22 kiloohms.

26 CLOCK 0Shift register for LED (CLK).

27 DATA oShift register for LED (DATA).

28 LINE MUTE oLine mute signal output.

29 BRAKE RELEASE oMotor drive control signal output. (”L” :BRAKE RELEASE)

30 PHONO IFunction control input for Phono mode.

31 TUNER IFunction control input for Tuner mode.

32 CD IFunction control input for CD mode.

33 AUX IFunction control input for AUX mode.

34 TAPE1 IFunction control input for Tape 1mode.

35 TAPE2 IFunction control input for Tape 2mode.

36 — — Connected the resistor 22 kiloohms.

37 POWER ON/OFF IPower ON/OFF control input.

38 K0 IGround.

39 K1 IGround.

40 K2 IMicrocomputer operation mode selection input.

41 K3 IMicrocomputer operation mode selection input.

42 MUTE IConnected the resistor 22 kiloohms.

-7-

SEMICONDUCTOR LEAD LAYOUTS 3-3.PRINTED WIRING BOARDS (KEY BOARD SECTION)

BA6208

IlKHMI

GP1U52XB

123

1Vout

2Vce

36ND

M5218AL

HPC1237HA

GNO

DTA124ES

DTC124ES

2SC2603-EF

2SC3622A-LK

2SA988-PAFAEA

2SA1371-E

2SC2545-E

2SA1 491 M-OPY

2SA1 492M-OPY

2SD2012

2SA1684-LK

2SC1 841 -PAFAEA

2SC1941-LK

2SC2259-FG

2SC3855M-OPY

2SC3856M-OPY

2SC4431-LK

2SK246-GR

HZS6C1L

HZS7C2L

HZS16-2L

UZ-3.0BS

11ES2

RBV-602-01

1N4148M

1SI 585

10E2

SEL2215R-CD

SEL3210S-CD

SEL3810A-CD

anode cathode

SEL3510C-CD

•SEMICONDUCTOR

LOCATION

Ref. No. Location

D703 1-9

D704 1-9

D708 !-5

D709 H- 13

D71

H-13

D71

H- 11

D71

H-10

D71

H-7

D71

H-9

D71

H-6

D71

H-13

D71

J-4

D71

H-16

D71

D720 X100

D721 H-6

D722 H-9

D723 H- 11

D724 H-12

D725 H-14

D800 mlA

IC702 H-4

IC705 1-12

Q700 i-9

Q701 1-8

Q702 i-8

Q703 1-10

Q704 H-6

Q705 H-5

Q706 1-5

Q707 i-5

Q709 I-13

Note:

•O:parts extracted from the component side.

•:Pattern on the side which is seen.

2345678910 11 12 13 14 15 16 1

TO SP BOARD

8910

•SEMICONDUCTOR LOCATION 3-4. PRINTED WIRING BOARDS (MAIN BOARD SECTION) •Refer to Page 8for Semiconductor Lead Layouts.

Ref. No. Location Ref. No. Location Ref. No. Location

D100 C-24 0909 E-28 Q609 1-26

D500 H-21 D91

E-7Q610 J-27

D501 H- 19 Q61

J-25

0502 i-20 Q612 J-27

D503 1-20 1C100 0-25 0613 E-23

1C300 F-21

D504 H-21 IC700 D-22 0708 E-24

D505 H-21 1C703 F- 17 Q710 E-23

D506 H-21 IC704 F- 17 Q71

D-5

D507 1-20 Q71

E-21

D508 1-22 1C800 F-20 Q713 F-5

1C902 D-5

D509 i-22 1C903 E-5Q714 D-20

D600 H-28 Q715 C-23

D601 H-27 0900 E-6

D602 H-26 Q100 C-26 Q901 E-27

D603 H-26 Q101 C-26 0902 F-27

G200 0-26

D604 1-28 G201 D-26

D605 1-28 Q500 H-20

D606 1-28

D607 1-26 Q501 H-21

D608 J-28 Q502 H-20

Q503 !-20

D609 J-28 Q504 1-21

D700 D -23 G505 1-20

D701 E-7

D702 E-7G506 H- 19

D705 E-22 Q507 J-22

Q508 1-21

D706 E-22 Q509 1-20

D707 F-22 G510 J-23

D727 D-6

D728 E-24 Q51

J-21

D729 E-24 Q512 i-22

Q513 E-23

D801 J-9Q600 H-27

0802 J-7Q601 H-28

0900 H-22

D901 G-25 Q602 ^H-27

0902 G-25 G603 |1-28

Q604 11-28

D904 E-8Q605 1-28

D905 E-8Q606 H-26

0906 E-8

D907 E-8Q607 J-26

D908 F-28 Q608 ;1-27

Note

There are two type of AEP models which are depend

on countries.

AEP2 model :Model for Scandinavian countries,

Switzerland, Spain and Portugal

AEP1 model :Model for other European countries

Note:

•O—:parts extracted from the component side.

•:Pattern on the side which is seen.

23456 7 8910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

11 -12 -13 -14 -

Note :

•All capacitors are in pF unless otherwise noted. pF: ppF

50WV or less are not indicated except for electrolytics and

tantalums.

•All resistors are in Qand V£W or less unless otherwise

specified.

•:nonflammable resistor.

:fusible resistor.

Note :The components identified by mark ^or dotted

line with mark ^are critical for safety.

Replace only with part number specified.

o;B+ Line

•:B—Line

91~1

:adjustment for repair.

9Voltage and waveforms are dc with respect to ground under

no-signal conditions,

no mark :CD

():F419R only

°Voltages are taken with aVOM (input impedance 1GM Q).

Voltage variations may be noted due to normal production

tolerances.

°Signal path.

:PHONO

Note

There are two type of AEP models which are depend

on countries.

AEP2 model :Model for Scandinavian countries,

Switzerland, Spain and Portugal

AEP1 model :Model for other European countries

15 16 17 18

3-6. 1C BLOCK DIAGRAM

IC703, 704 BA6208

Ce manuel convient aux modèles suivants

Autres manuels Sony Amplificateur

Sony

Sony XM-2200GTX Operating & Mounting Manuel utilisateur

Sony

Sony TA-P9000ES - Amplifier Manuel utilisateur

Sony

Sony TA-KMSW500 Manuel utilisateur

Sony

Sony XM-D6000GTX - Car Monaural Power Amplifier Manuel utilisateur

Sony

Sony XM-405EQX2 Manuel utilisateur

Sony

Sony TA-3200F Guide de configuration

Sony

Sony TA-F4A Manuel utilisateur

Sony

Sony XDP-210EQ Manuel utilisateur

Sony

Sony TA-AV501 Manuel utilisateur

Sony

Sony XDP-4000X Operating Instructions (primary... Manuel utilisateur

Sony

Sony SLV-AV100U Manuel utilisateur

Sony

Sony XES-M50 Manuel utilisateur

Sony

Sony XM-GTR2202 Manuel utilisateur

Sony

Sony SPA-3 Manuel utilisateur

Sony

Sony XM-1600GSD Marketing Specifications,... Manuel utilisateur

Sony

Sony TA-N1 Manuel utilisateur

Sony

Sony XM-7557 Primary Manuel utilisateur

Sony

Sony XM-3001SXD - Stereo Power Amplifier Manuel utilisateur

Sony

Sony XM-D400P5 Product Guide Manuel utilisateur

Sony

Sony XM-D9001GTR Manuel utilisateur

Sony

Sony EA-80 Manuel utilisateur

Sony

Sony XM-N1004 Manuel utilisateur

Sony

Sony TA-A400 Manuel utilisateur

Sony

Sony XM-5540F Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur

Phonic

Phonic XP 3000 Manuel utilisateur