SonicWALL SonicWave 432o Manuel utilisateur

Safety and Regulatory Information

SonicWall™ SonicWave 432o

Getting Started Guide

IMPORTANT: This device must be professionally installed using either the

supplied antennas, or with other approved antennas available from SonicWall.

Regulatory Model Numbers:

APL42‐0C1 (SonicWave 432o)

Professional Installation ValidationBecause of the unique market and functionality

targeted by this product, the SonicWave 432o requires specially trained professionals to configure and install the

product. Also, according to FCC rules (similar rules in other regulatory domains), you are required to consult with

an experienced professional RF installer/dealer/technician to conduct the installation, conform to the regulation,

and correct the interference from the standard industry measures. The FCC requires you to be notified that any

changes or modifications made to the device that are not expressly approved by SonicWall could void your

authority to operate the equipment.

A professional installer is responsible for the proper installation and configuration of the outdoor SonicWave. The installer

needs to understand and prepare for operating near any Terminal Doppler Weather Radar (TDWR) locations based on the

FCC Memorandum and comply with all its requirements.

The professional installer needs to choose the correct antenna type and its gain should be so chosen that the

equivalent isotropically radiated power (EIRP) is not more than that required for successful communication to

ensure the reduction of potential radio interference with other users.

The professional installer must also properly select the current country of operation from the SonicWall

configuration interface. Incorrectly entering the country of operation could

SonicWall SonicWave 432o Getting Started Guide

result in illegal operation and might cause harmful interference to other systems.

SonicWall Inc. hereby declares that this product is distributed through our controlled distribution channel and

requires that trained professionals are to install this product, and we will not sell this product directly to the general

public through retail stores.

Safety and Regulatory Information

WARNING: Electrical Hazard: Only qualified personnel should perform installation procedures. Within the

context of the safety notes in this documentation qualified persons are defined as persons who are

authorized to commission, ground and label devices, systems, and circuits in accordance with established

safety practices and standards. A qualified person understands the requirements and risks involved with

installing outdoor electrical equipment in accordance with national codes.

Restricted Access location. This product is not intended to be installed and used in a home or public area

accessible to the general population.

Ground Connection

The ground connection for the SonicWave 432o is located on the back of the device. Attach the green ground to

earth cable to the grounding terminal.

1Use the ground screw assembly, with the star washer, to attach the ground wire’s ring terminal to the

SonicWave. The wire should be as close to the SonicWave bottom as possible.

2Tighten the screw securely.

Mounting the SonicWave 432o Appliance

IMPORTANT: This device must be professionally installed.

Attach the SonicWave 432o to a surface that can support it and withstand its environment. It can be mounted to a

wall, girder, or pole, and the surface material can be concrete, brick, wood, metal, or plastic.

Mount the SonicWave so that the input and output ports are on the right side of the SonicWave. You should provide

a threeinch drip loop on all cables.

To mount the SonicWave 432o on a wall:

1Using the wall‐mount base as a guide, mark the location of the mounting screws on the wall surface.

2Using a drill, drill four mounting holes into the wall as follows:

•for installing the SonicWave on a masonry wall, use a 5/16” diameter bit.

•for other materials, use the appropriate drill for the screws being used.

3For masonry installations, place four anchor assemblies into the holes.

Attaching the Mounting Bracket to the SonicWave

Attach the mounting bracket to the back of the SonicWave 432o using four M4 screws, four spring washers, and

four flat washers:

1Attach the SonicWave 432o and base assembly to the wall using the provided mounting bolts.

2Finger tighten the mounting screws securely, but do not apply more torque than is necessary.

3Secure the anchors to the wall, and then secure the bracket to the anchors.

Safety and Regulatory Information

NOTE: Use anchors when mounting to cement walls. Mounting screws are not included.

Mounting the SonicWave 432o on a Pole

IMPORTANT: This device must be professionally installed using either the supplied antennas or with

approved alternate antennas available from SonicWall.

To mount the SonicWave 432o unit on a pole:

1. Fasten the wall‐mount base securely to the back of the SonicWave 432o using the provided mounting screws.

2. Attach the pole‐mount bracket to the wall‐mount base using with the provided screws. The pole‐mount bracket

can be attached either vertically or at a tilt of up to 30 degrees, depending on your requirements.

3. Loop the provided pole strap through the slots on the pole‐mount bracket and then around the pole.

4. Tighten the strap with an appropriate screw driver and ensure that the device is firmly in place.

Installing SonicWave 432o Antennas

Install the external antennas (or approved alternates) intended for area coverage. The SonicWave 432o features

dual concurrent radio signals. Use the 2.4 GHz antennas to access Radio 1 (802.11 b/g/n at 600 Mbps) signals, and

the 5 GHz antennas to access Radio 2 (802.11 a/n/ac at 1733 Mbps) signals. You should use all eight WiFi antennas

to utilize both radio frequencies concurrently.

CAUTION: To prevent damage to the SonicWave, do not enable the radios without all

RF output ports connected to an antenna.

To install the antennas on your SonicWave 432o:

1. Remove all eight antennas from their bags and place one on each of the appropriate connectors,

matching the radio signals marked on the antennas to those marked above the connectors

2. Insert the antenna base firmly into the antenna mount.

3. Carefully finger‐tighten the fittings being cautious not to over‐tighten them.

4. Repeat with the remaining antennas.

Safety and Regulatory Information

Installing the appliance

For your safety, follow all instructions listed in this section.

Install in a location away from direct sunlight and sources of heat. A maximum ambient temperature of

140º F (60º C) is recommended.

Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios,

transmitters, and broadband amplifiers

The included power cord(s) are approved for use only in specific countries or regions. Before using a power

cord, verify that it is rated and approved for use in your location.

Ensure that no water or excessive moisture can enter the unit.

Allow unrestricted airflow around the unit and through the vents on the side of the unit. A minimum of 1

inch (25.44mm) clearance is recommended.

Consideration must be given to the connection of the equipment to the supply circuit. Appropriate

consideration of equipment nameplate ratings must be used when addressing this concern. Do not

overload the circuit.

This product is not intended to be installed and used in a home or public area accessible to the general

population. When installed in schools, this equipment must be installed in a secure location accessible only

by trained personnel.

This device is not intended for use at workplaces with visual display units, in accordance with §2 of the

German ordinance for workplaces with visual display units. To avoid incommoding reflections at visual

display workplaces this device must not be placed in the direct field of view.

Safety and Regulatory Information

Cable connections

RS232 (Console) cables are designed for intra-building connection to other equipment. Do not connect these ports

directly to communication wiring or other wiring that exits the building where the SonicWall appliance is located.

Power supply information for APL42-0C1

This product’s power is provided by the Ethernet cable plugged into the “LAN” port, this is called “Power Over

Ethernet” or “POE.” The POE source should only be UL listed marked “Class 2” or “LPS,” with an output rated 48

VDC, minimum 1.26 A, Tma: minimum 40 degrees C.

Restricted environments

The SonicWall wireless device, like other radio devices, emits radio frequency electromagnetic energy. The

SonicWall wireless device operates within the guidelines found in radio frequency safety and recommendations.

These standards and recommendations reflect the consensus of the scientific community and result from

deliberations of panels and committees of scientists who continually review and interpret the extensive research

literature. In some situations or environments, the use of the SonicWall wireless device may be restricted by the

proprietor of the building or responsible representatives of the applicable organization.

Examples of such situations include the following:

Using the SonicWall wireless device equipment on board airplanes, or

Using the SonicWall wireless device equipment in any other environment where the risk of interference with

other devices or services is perceived or identified as being harmful.

If you are uncertain of the policy that applies to the use of wireless devices in a specific organization or

environment (an airport, for example), you are encouraged to ask for authorization to use the SonicWall wireless

device before you turn it on.

Explosive Device Proximity Warning: Do not operate a portable transmitter (such as a

wireless network device) near unshielded blasting caps or in an explosive environment

unless the device has been modified to be qualified for such use.

Use on Aircraft Caution: Regulations of the FCC and FAA prohibit airborne operation of

radio-frequency wireless devices because their signals could interfere with critical

aircraft instruments.

Safety and Regulatory Information

Radio approvals

It is important to ensure that you only use your radio device in countries where the device is approved for use. To

determine whether you are allowed to use your wireless network device in a specific country, check to see if the

radio type number that is printed on the identification label of your device or listed on the radio approval list

posted on the general SonicWall support site at: https://support.sonicwall.com.

Radio or television interference

The SonicWall SonicWAve 432o wireless network device must be installed and used in strict accordance with the

manufacturer’s instructions as described in the user documentation that comes with the product. SonicWall Inc.

is not responsible for any radio or television interference caused by unauthorized modification of the devices

included with this SonicWall Wireless device kit, or the substitution or attachment of connecting cables and

equipment other than that specified by SonicWall Inc. The correction of interference caused by such unauthorized

modification, substitution or attachment is the responsibility of the user. SonicWall Inc. and its authorized resellers

or distributors are not liable for any damage or violation of government regulations that may arise from the user

failing to comply with these guidelines.

Wireless interoperability

The SonicWall Wireless WLAN products are designed to be interoperable with any wireless LAN product that is

based on direct sequence spread spectrum (DSSS) radio technology and orthogonal frequency division multiplexing

(OFDM) and to comply with the following standards:

IEEE 802.11a\ac Standard on 5 GHz Wireless LAN

IEEE 802.11b-1999 Standard on 2.4 GHz Wireless LAN

IEEE 802.11g Standard on 2.4 GHz Wireless LAN

IEEE 802.11n Standard on 2.4 GHz and 5 GHz Wireless LAN

Wireless Fidelity (Wi-Fi) certification, as defined by the WECA (Wireless Ethernet Compatibility Alliance)

Declaration of conformity

A “Declaration of Conformity” in accordance with the directives and standards has been made and is on file at

SonicWall International Limited, City Gate Park, Mahon, Cork, Ireland.

CE declarations can be found online at https://support.sonicwall.com.

Additional regulatory notifications and information for this product can be found online at

https://support.sonicwall.com.

Safety and Regulatory Information

EU and EFTA

This device is approved for use in EU member states and EFTA countries as shown on the appliance label.

SonicWave 432o (RM: APL42-0C1) RF Transmitter Bands and

Power

I’ll l

Maximum Radio-Frequency Power Transmitted

MHz

dBm EIRP

2402 - 2480

9.05

2412 - 2472

19.76

5260 - 5320

Not currently supported

5500 - 5700

29.47

Sicherheitshinweise für den Einbau und

Betrieb

Weitere hinweise zur montage

Kabelverbindungen

Hinweis zur Lithiumbatterie

Informationen zur stromversorgung APL42-0C1

Weitere hinweise zur montage

Zu Ihrer eigenen Sicherheit beachten Sie alle in diesem Abschnitt aufgeführten Anweisungen.

Wählen Sie für die Montage einen Ort, der keinem direkten Sonnenlicht ausgesetzt ist und sich nicht in der

Nähe von Wärmequellen befindet. Die Umgebungstemperatur darf nicht mehr als 60 °C betragen.

Führen Sie die Kabel nicht entlang von Stromleitungen, Leuchtstoffröhren und Störquellen wie Funksendern

oder Breitbandverstärkern.

Das im Lieferumfang enthaltene bzw. die im Lieferumfang enthaltenen Netzkabel sind nur für die

Verwendung in bestimmten Ländern und Regionen zugelassen. Überprüfen Sie bitte vor der Verwendung eins

Netzkabels, ob es für die Verwendung in Ihrem Land oder Ihrer Region zugelassen ist und den geforderten

Normen entspricht.

Stellen Sie sicher, dass das Gerät vor Wasser und hoher Luftfeuchtigkeit geschützt ist.

Safety and Regulatory Information

Stellen Sie sicher, dass die Luft um das Gerät herum zirkulieren kann und die Lüftungsschlitze an der Seite des

Gehäuses frei sind. Hier ist ein Belüftungs-abstand von mindestens 26 mm einzuhalten.

Prüfen Sie den Anschluss des Geräts an die Stromversorgung, damit der Überstromschutz sowie die

elektrische Leitung nicht von einer eventuellen Überlastung der Stromversorgung beeinflusst werden. Prüfen

Sie dabei sorgfältig die Angaben auf dem Aufkleber des Geräts. Überlasten Sie nicht den Stromkreis.

Dieses Produkt ist nicht dafür entwickelt, um in Bereichen mit öffentlichem Zugang betrieben zu werden.

Wenn es in Schulen betrieben wird, stellen Sie sicher, dass das Gerät in einem abgeschlossenen Raum

installiert wird, der nur von speziell ausgebildetem Personal betreten werden kann.

Dieses Gerät ist nicht zur Verwendung an Arbeitsplätzen mit visuellen Anzeigegeräten gemäß § 2 der

deutschen Verordnung für Arbeitsplätze mit visuellen Anzeigegeräten vorgesehen. Um störende Reflexionen

am Bildshirmarbeitsplatz zu vermeiden, darf dieses Produkt nicht im unmittelbaren Gesichtsfeld platziert

verden.

Kabelverbindungen

RS232-C-Kabel eignen sich für die Verbindung von Geräten in Innenräumen. Schließen Sie an die Anschlüsse der

SonicWallkeine Kabel an, die aus dem Gebäude herausgeführt werden, in dem sich das Gerät befindet.

Informationen zur stromversorgung

APL42-0C1

Die Stromversorgung durch das Ethernet-Kabel in die “LAN”-Anschluss angeschlossen vorgesehen ist, wird dies als

“Power over Ethernet” oder “PoE.” Dieses Produkt darf nur in Verbindung mit einem für den Europäischen Markt

genehmigten und mit dem Logo „LPS.“ Ausgang: 48 VDC Gleichsspannung, mind. 1,26 A, mindest TMA mindestens

40° Grad C, betrieben werden.

Agency specific information

FCC ID: 2AKCZ-0C1

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the manufacturer's instruction manual, may cause interference with radio and television

reception.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15

of the FCC Rules.

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause undesired

operation.

Safety and Regulatory Information

The FCC regulations provide that changes or modifications not expressly approved by SonicWall Inc.

could void your authority to operate this equipment.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference with radio or television reception, which can be determined by

turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the

following measures:

Reorient the receiving antenna.

Relocate the system with respect to the receiver.

Move the system away from the receiver.

Plug the system into a different outlet so that the system and the receiver are on different branch circuits.

If necessary, consult a representative of SonicWall Inc. or an experienced radio/television technician for additional

suggestions.

This SonicWall Wireless WLAN device must be installed and used in strict accordance with the

manufacturer's instructions as described in the user documentation that comes with the product. Any

other installation or use will violate FCC Part 15 regulations. Modifications not expressly approved by

SonicWall could void your authority to operate the equipment.

The following information is provided on the device or devices covered in this document in compliance with FCC

regulations:

Product name:

SonicWall SonicWave 432o

Regulatory Model: APL42-0C1

Company name: SonicWall Inc. is the responsible party for this product. For an EMC compliance issue or a

regulatory inquiry, please use the following contact information:

SonicWall Inc.

5455 Great America Parkway

Santa Clara, CA 95054 USA

408-745-9600

Radiation exposure statement (FCC)

The radiated output power of this device is below the FCC radio frequency exposure limits.

Nevertheless, this device should be used in such a manner that the potential for human contact

during normal operation is minimized. This device has been evaluated for and shown compliant

with the FCC RF Exposure limits under mobile exposure conditions (antennas are greater than 58

cm from a person’s body). Details of the authorized configurations can be found at

https://fjallfoss.fcc.gov/oetcf/eas/reports/GenericSearch.cfm by entering the FCC ID number on

the device.

United States of America authorized channels

SonicWall declares that the APL42-0C1 (FCC ID: 2AKCZ-0C1) when sold in the USA is limited to CH1-CH11 by

specified firmware controlled in the USA.

Safety and Regulatory Information

This device is restricted to indoor use due to its operation in the 5.15GHz to 5.25GHz frequency

range. The FCC requires this product to be used indoors for the frequency range 5.15GHz to

5.25GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.

The APL42-0C1 device has been designed to operate with an antenna having a maximum gain of 12.91 dBi for 2.4

GHz and 14.6 dBi for 5GHz. Antenna having a higher gain is strictly prohibited. The required antenna impedance is

50 ohms. Only antennas approved by Sonicwall are allowed.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Autres manuels pour SonicWave 432o

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels SonicWALL Point d'accès sans fil

SonicWALL

SonicWALL SMA 100 Series Guide de référence rapide

SonicWALL

SonicWALL SonicWave 641 Manuel utilisateur

SonicWALL

SonicWALL E-Class SonicPoint-Ne Manuel utilisateur

SonicWALL

SonicWALL TZ300P Manuel du propriétaire

SonicWALL

SonicWALL SonicPoint ACe Manuel utilisateur

SonicWALL

SonicWALL SonicPoint Manuel utilisateur

SonicWALL

SonicWALL sonicpoint ACI Manuel utilisateur

SonicWALL

SonicWALL APL30-0B8 Manuel du propriétaire

SonicWALL

SonicWALL SonicWave 231c Manuel utilisateur

SonicWALL

SonicWALL SonicWave 681 Manuel utilisateur

SonicWALL

SonicWALL ex9000 Manuel utilisateur

SonicWALL

SonicWALL APL29-0B6 Manuel du propriétaire

SonicWALL

SonicWALL APL62-0F7 Manuel du propriétaire

SonicWALL

SonicWALL SonicWave 432e Manuel utilisateur

SonicWALL

SonicWALL SonicWave 231o Manuel du propriétaire

SonicWALL

SonicWALL SonicWave 200 Series Guide de référence rapide

SonicWALL

SonicWALL TZ500 W Manuel du propriétaire

SonicWALL

SonicWALL APL13-02C Manuel utilisateur

SonicWALL

SonicWALL SonicWave 432o Manuel utilisateur

SonicWALL

SonicWALL SonicWave 224w Manuel du propriétaire

SonicWALL

SonicWALL APL43-0C2 Manuel du propriétaire

SonicWALL

SonicWALL SonicWave 432o Manuel utilisateur

SonicWALL

SonicWALL SonicWave 200 Series Guide de référence rapide

SonicWALL

SonicWALL SonicWave 400 Series Guide de référence rapide

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur