SonicWALL SonicWave 231o Manuel du propriétaire

SonicWall Error! Unknown document property name.

Safety and Regulatory Information

SonicWall® SonicWave 231o Safety and

Regulatory Information

Regulatory Model Number APL46‐0D1

Draft June 2018

IMPORTANT: This device must be professionally installed using either the supplied antennas, or with other

approved antennas available from SonicWall.

This document contains safety and regulatory information for the SonicWall® SonicWave 231o. The SonicWave

231o is a wireless access point with an internal wireless radio that can provide wireless access on either 5GHz

or 2.4GHz and supports the 802.11 ac/n/g/a/b standards.

Topics:

Professional Installation Validation

Mounting the SonicWave 231o

Safety Information for Installation and Operation

Informations de sécurité pour l'installation et le fonctionnement

Sicherheitshinweise für den Einbau und Betrieb

安全信息安裝和操作

安全信息安装和操作

製品の安全性と規定に関する情報

제품 안전 및규정 정보

Informações normativas e sobre a segurança dos produtos

Agency specific information

Error! Reference source not found.

EMC agency specific information

Safety and Regulatory Information

Professional Installation Validation

Because of the unique market and functionality targeted by this product, the SonicWave 231o requires

specially trained professionals to configure and install the product. Also, according to FCC rules (similar rules in

other regulatory domains), you are required to consult with an experienced professional RF

installer/dealer/technician to conduct the installation, conform to the regulation, and correct the interference

from the standard industry measures. The FCC requires you to be notified that any changes or modifications

made to the device that are not expressly approved by SonicWall could void your authority to operate the

equipment.

A professional installer is responsible for the proper installation and configuration of the SonicWave 231o. The

installer needs to understand and prepare for operating near any Terminal Doppler Weather Radar (TDWR)

locations based on the FCC Memorandum and comply with all its requirements.

The professional installer needs to choose the correct antenna type and its gain should be so chosen that the

equivalent isotropically radiated power (EIRP) is not more than that required for successful communication to

ensure the reduction of potential radio interference with other users.

The professional installer must also properly select the current country of operation from the SonicWall

configuration interface. Incorrectly entering the country of operation could result in illegal operation and

might cause harmful interference to other systems.

SonicWall Inc. hereby declares that this product is distributed through our controlled distribution channel and

requires that trained professionals are to install this product, and we will not sell this product directly to the

general public through retail stores.

WARNING: Electrical Hazard: Only qualified personnel should perform installation procedures.

Within the context of the safety notes in this documentation qualified persons are defined as persons

who are authorized to commission, ground and label devices, systems, and circuits in accordance

with established safety practices and standards. A qualified person understands the requirements

and risks involved with installing outdoor electrical equipment in accordance with national codes.

Restricted Access location. This product is not intended to be installed and used in a home or public

area accessible to the general population. When installed in schools, this equipment must be

installed in a secure location accessible only by trained personnel.

If you have any questions regarding the authorization, contact your SonicWall vendor for professional

installation details.

Mounting the SonicWave 231o

IMPORTANT: This device must be professionally installed. For safety tips when mounting the

SonicWave 231o, see Safety information for installation and operation.

Attach the SonicWave 231o to a surface that can support it and withstand its environment. It can be mounted

to a post or pole, and the surface material can be concrete, brick, wood, metal, or plastic.

Topics:

Ground Connection

Mounting the SonicWave 231o on a Pole or Post

Installing SonicWave 231o Antennas

Connecting Ethernet Cables

Safety and Regulatory Information

Ground Connection

The ground connection for the SonicWave 231o is located on the back of the device. Attach the green ground

to earth cable to the grounding terminal.

To attach the green ground to earth cable to the grounding terminal:

1Use the ground screw assembly with the star washer to attach the ground wire’s ring terminal to the

SonicWave 231o. The wire should be as close to the SonicWave bottom as possible.

2Tighten the screw securely.

IMPORTANT: This device must be professionally installed using either the supplied antennas or with

approved alternate antennas available from SonicWall.

Safety and Regulatory Information

Installing the Mounting Bracket

The SonicWave 231o mounting kit includes hardware for mounting the unit

outside on a pole or post, or on a wall or other flat surface. The SonicWave 231o

and mounting bracket are designed so that you can first attach the mounting

bracket to the pole or wall and then slide the SonicWave onto the bracket.

To attach the mounting bracket to a pole or post:

1 Using a screwdriver, loosen and free the ends of the two adjustable pole straps.

2 Insert each pole strap through an appropriate slot on the back side of the bracket.

3 Loop the straps around the pole or post.

4 Insert the strap ends into their respective fittings until snug around the pole.

5 Use the screwdriver to tighten each strap and securely attach the mounting bracket to

the pole or post.

To attach the mounting bracket to a wall or flat surface:

1 Place the back side of the mounting bracket against the wall or surface and mark the

locations for four screws positioned at the mounting screw insertion points.

2 Drill starter holes at the marked locations. For a wood wall, use a drill bit that fits the

provided screws. For drywall, use a drill bit that fits the anchors. Use the screws or

anchors that work best in your location.

3 For drywall, insert or screw in the anchors.

4 Place the mounting bracket against the wall with the mounting screw insertion points

lined up on the marks or anchors.

5 Using the provided screws and a screwdriver, securely attach the mounting bracket to

the wall or surface.

Safety and Regulatory Information

Installing SonicWave 231o Antennas

IMPORTANT: This device must be professionally installed using either the supplied antennas or with

approved alternate antennas available from SonicWall.

CAUTION: To prevent damage to the SonicWave 231o, all RF output ports must be attached to an

approved antenna before the radios are enabled.

To install the antennas on your SonicWave 231o:

1Remove all four antennas from their bags and place one on each of the appropriate connectors,

matching the radio signals marked on the antennas to those marked above the connectors.

2Insert the antenna base firmly into the antenna mount.

3Making sure there is no cross threading, fully tighten the silver knurled fitting using your fingers to the

point that it cannot turn with moderate force. Do not use or twist the white antenna housing enclosure

while securing the antenna.

4Repeat Step 2 and Step 3 for each antenna.

Safety and Regulatory Information

Available Antennas for the SonicWave 231o

The following antennas are approved for use with the outdoor SonicWave 231o.

NOTE: For NEMA Type 4X compliance use default antennas D121‐05/D151‐07.

Antenna Mode

Band (GHz)

Antenna Gain (dBi)

Antenna Type

Deflection

Default: D121‐05*/D151‐07*

2.4/5G

5dBi/7dBi

Omni/Dipole

360°

S122‐12†

2.4

12dBi

Sector

120°

S152‐15†

15dBi

Sector

120°

* Default antennas provided with appliance.

† S122‐12 and S152‐15 must be used together.

CAUTION: To prevent damage to the SonicWave 231o, all RF output ports must be attached to an

approved antenna before the radios are enabled.

For details regarding these alternately approved antennas (including important safety information) refer to the

respective antenna guides. Some antennas might not be offered for sale in all countries. Contact SonicWall for

purchasing information.

The SonicWave default antenna configuration only supports Omni/Dipole antennas as shipped from the

factory. When any other antenna or antenna pair is installed, the professional installer must correctly

configure the SonicWave for the new antennas before enabling the radios. Configuration instructions are

included in this guide and with each antenna.

Connecting Ethernet Cables

Provide adequate grounding to the SonicWave 231o and the PoE injector. The grounding screw and wire are

provided for this purpose. Consult a certified electrician to ensure that all grounding and cabling is installed in

compliance with local electrical codes. The SonicWave 231o is powered through Power over Ethernet (PoE),

and should be cabled with CAT5e Ethernet cabling.

When using PoE, a SonicWall 802.3afcompliant midspan PoE line injector (sold separately), or an

802.3afcompliant switch is required to power each SonicWave 231o.

NOTE: To maximize the SonicWave 231o’s power capabilities, connect the PoE to a 2.5Gb port on the

firewall.

Safety and Regulatory Information

To connect PoE to a SonicWave 231o:

1Install the cable gland adapter assembly through the LAN/PoE sealing nut, slide claw, and seal onto the

RJ45 Ethernet cable.

2Slide the seal and claw into the SonicWave 231o port.

3Secure the seal nut onto the main assembly body.

4Tighten the assembly by hand (finger‐tight).

IMPORTANT: Be sure cables are connected correctly.

5Plug the power cord of the SonicWall PoE injector into an appropriate power outlet.

6Wait for the LAN1 LED on the SonicWave 231o to illuminate green. This indicates an active connection.

CAUTION: A multi‐gigabit 802.3afcompliant PoE injector or PoE‐capable switch is required

to provide power to each SonicWave 231o. To maintain power to the SonicWave 231o, the

maximum length of CAT 5e cable from the 802.3afPoE injector to the SonicWave 231o is 100

meters (333 feet).

Configuring the Antennas

Once the SonicWave 231o is powered up, the professional installer can use an

app such as BusyBox to SSH to it at the default IP address (192.168.1.20) and run

the proinstall command sequence. After typing proinstall on the command

line, you are prompted for a passcode. Type in the serial number of the

SonicWave as a hex string with all letters in uppercase for the passcode.

The following is an example configuration:

~ # proinstall

Welcome to SonicWall SonicWave Professional Install Mode. By

entering the passcode, you accept and agree to the terms and

conditions of the agreement from

HTTPS://WWW.SONICWALL.COM/LEGAL/EUPA.ASPX.

You also confirm yourself as the certified RF professional

installer and are obligated to ensure the SonicWave is

operating according to the channel limitations, outdoor

restrictions and license requirements for different domains

and countries.

Passcode:********

PRO->help

help -- Provide all commands available with description.

show all-antennas -- Show all available antennas

show radio-antenna-settings -- Show the current antenna

options for both radio 0(5GHz) and radio 1(2.4GHz)

set radio [0 | 1] antenna [0|1|2|3|4|5|6|7] -- Set antenna for

radio 0(5GHz radio) or radio 1(2.4GHz)

commit -- Apply changes

exit -- Leave the professional install mode

PRO->show all-antennas

All Available antennas:

0 - Default (2.4GHz / 5GHz)

1 - S124-12 (2.4GHz Only)

2 - S154-15 (5GHz Only)

PRO->show radio-antenna-settings

Radio 0 (5GHz): 0 - Default (2.4GHz / 5GHz)

Radio 1 (2.4GHz): 0 - Default (2.4GHz / 5GHz)

PRO->set radio 0 antenna 2

PRO->set radio 1 antenna 1

PRO->show radio-antenna-settings

Radio 0 (5GHz): 2 - S154-15 (5GHz Only)

Radio 1 (2.4GHz): 1 - S124-12 (2.4GHz Only)

Safety and Regulatory Information

PRO->commit

Are you want to save changes and reboot system to take effect

(y/n):y

The system will reboot in 0s ...

Safety and Regulatory Information

Safety Information for Installation and

Operation

This section provides the following product safety and regulatory information:

Installing the Appliance

Approved Alternate Antennas

RF Safety Distance

Professional Installation Notice

Error! Reference source not found.

Power Supply Information

Restricted Environments

Radio Approvals

Radio or Television Interference

Wireless Interoperability

SonicWave 231o complies with FCC U‐NII New Rules.

Regulatory Model/Type

Product Name

APL46‐0D1

SonicWave 231o

NOTE: Additional regulatory notifications and information for this product can be found

online at: https://www.sonicwall.com/support/technical-documentation.

NOTE: For NEMA Type 4X compliance, use the optional NEMA Type 4X mounting kit (purchased

separately) and default antennas D121‐05/D151‐07.

Safety and Regulatory Information

Installing the Appliance

WARNING: The following conditions are required for proper installation:

1Mount in a location away from direct sunlight and sources of heat. A maximum ambient temperature of

140º F (60º C) is recommended.

2Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios,

transmitters, and broadband amplifiers.

3Ensure that no water or excessive moisture can enter the unit.

4Allow unrestricted airflow around the unit. A minimum of 1 inch (25.44mm) clearance is recommended.

5Consideration must be given to the connection of the equipment to the supply circuit and that the

effect of overloading the circuits has minimal impact on overcurrent protection and supply wiring.

Appropriate consideration of equipment nameplate ratings must be used when addressing this concern.

6This equipment is not intended for use at workplaces with visual display units, in accordance with §2 of

the German ordinance for workplaces with visual display units. To avoid incommoding reflections at

visual display workplaces, this device must not be placed in the direct field of view.

7This product is not intended to be installed and used in a home or public area accessible to the general

population. When installed in schools, this equipment must be installed in a secure location accessible

only by trained personnel.

Approved Alternate Antennas

Alternate antennas used with the SonicWave 231o must be approved and certified before use. However, in

order to comply with the local laws and regulations, an approval might be required by the local regulatory

authorities.

The included antennas have been tested and approved for use with the SonicWave 231o model.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that

the equivalent isotropically radiated power (e.i.r.p) is not more than that required for successful

communication.

Contact SonicWall for a list of antennas approved for use with the SonicWave 231o.

RF Safety Distance

The antennas used for this transmitter must be installed to provide a separation distance of at least 40 cm

from all persons and must not be co‐located or operating in conjunction with another antenna or transmitter.

Professional Installation Notice

To comply with FCC part 15 rules in the United States, the SonicWave 231o must be professionally installed to

ensure compliance with the Part 15 certification. It is the responsibility of the operator and professional

installer to ensure that only certified systems are deployed in the United States. The use of the system in any

other combination (such as co‐located antennas transmitting the same information) is expressly forbidden.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SonicWALL Point d'accès sans fil

SonicWALL

SonicWALL SonicPoint ACe Manuel utilisateur

SonicWALL

SonicWALL APL30-0B8 Manuel du propriétaire

SonicWALL

SonicWALL SonicWave 400 Series Guide de référence rapide

SonicWALL

SonicWALL ex9000 Manuel utilisateur

SonicWALL

SonicWALL E-Class SonicPoint-Ne Manuel utilisateur

SonicWALL

SonicWALL SonicWave 400 Series Manuel utilisateur

SonicWALL

SonicWALL SonicWave 432o Manuel utilisateur

SonicWALL

SonicWALL SonicWave 432i Manuel du propriétaire

SonicWALL

SonicWALL APL62-0F7 Manuel du propriétaire

SonicWALL

SonicWALL SonicPoint Manuel utilisateur

SonicWALL

SonicWALL APL43-0C2 Manuel du propriétaire

SonicWALL

SonicWALL SonicWave 641 Manuel utilisateur

SonicWALL

SonicWALL SonicWave 681 Manuel utilisateur

SonicWALL

SonicWALL SonicWave 200 Series Guide de référence rapide

SonicWALL

SonicWALL APL29-0B6 Manuel du propriétaire

SonicWALL

SonicWALL SonicWave 224w Manuel du propriétaire

SonicWALL

SonicWALL SonicPoint N2 Manuel utilisateur

SonicWALL

SonicWALL APL13-02C Manuel utilisateur

SonicWALL

SonicWALL SonicWave 200 Series Guide de référence rapide

SonicWALL

SonicWALL SonicWave 200 Series Guide de référence rapide

SonicWALL

SonicWALL SOHO 250 Manuel du propriétaire

SonicWALL

SonicWALL SonicWave 432o Manuel utilisateur

SonicWALL

SonicWALL sonicpoint ACI Manuel utilisateur

SonicWALL

SonicWALL TZ500 W Manuel du propriétaire

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur