SOMFY Sonesse 28 WF Zigbee Manuel utilisateur
Sonesse 28 WF RTS
EN Instructions
EN Sonesse 28 WF RTS
2Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved.
ORIGINAL INSTRUCTIONS
These instructions apply to all Sonesse 28 WF RTS drives, the different versions of
which are available in the current catalogue.
CONTENTS
1.
Prior information...........................................................................................
4
1.1.
Field of application............................................................................
4
1.2.
Liability ...............................................................................................
4
2.
Installation......................................................................................................
5
2.1.
Assembly ............................................................................................
5
2.2.
Wiring .................................................................................................
6
2.3.
Commissioning ..................................................................................
7
2.4.
Tips and advice on installation.........................................................
9
3.
Use and maintenance ....................................................................................
14
3.1.
Mode selection: Roller or Tilting Mode..........................................
14
3.2.
Controlling Up, Down, My: in Roller mode ....................................
14
3.3.
Controlling Up, Down, My: in Tilting mode....................................
15
3.4.
Favourite position (my) ....................................................................
15
3.5.
Adjusting the speed...........................................................................
16
3.6.
Tips and advice on operation...........................................................
17
4.
Technical data ................................................................................................
19
Sonesse 28 WF RTS EN
Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved. 3
GENERAL INFORMATION
Safety instructions
DANGER
Indicates a danger which may result in immediate death or
serious injury.
WARNING
Indicates a danger which may result in death or serious
injury.
PRECAUTION
Indicates a danger which may result in minor or moderate
injury.
CAUTION
Indicates a danger which may result in damage to or
destruction of the product.
EN Sonesse 28 WF RTS
4Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved.
1.PRIOR INFORMATION
1.1.Field of application
The Sonesse 28 drives are designed to drive all types of interior blinds except
pantographs.
The installer, who must be a motorisation and home automation professional, must
ensure that the motorised product is installed in accordance with the standards in
force in the country in which it is installed such as EN 13120 relating to interior blinds.
1.2.Liability
Before installing and using the drive, please read these instructions carefully.
In addition to the instructions provided in this guide, please also comply with the
instructions provided in the attached Safety instructions document.
The drive must be installed by a home motorisation and automation
professional, in accordance with Somfy’s instructions and the applicable
regulations in the country of installation.
Any operation of the drive outside the field of application described above is
prohibited. Such use, and any failure to comply with the instructions given in this guide
and in the attached Safety instructions document, absolves Somfy of any liability and
invalidates the warranty.
After installing the drive, the installer must inform his customers of the operating and
maintenance conditions for the drive and must provide them with the operating and
maintenance instructions, and the attached Safety instructions document. Any After-
Sales Service operation on the drive must be performed by a home motorisation and
automation professional.
Never begin installing without first checking the compatibility of this product with the
associated equipment and accessories. If in doubt when installing this product and/or
to obtain additional information, contact a Somfy representative or visit the website
www.somfy.com.
Sonesse 28 WF RTS EN
Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved. 5
2.INSTALLATION
CAUTION
•
These instructions are mandatory for the home motorisation and
automation professional installing the drive.
•
Never drop, knock or puncture the drive or immerse it in liquid.
•
Install an individual control point for each drive.
NOTICE
Make sure that LED, programming button and input connection remain visible and
easily accessible after installation.
2.1.Assembly
2.1.1.Preparing the drive
CAUTION
Sonesse 28 WF RTS : interior diameter of the tube has to be Ø26.6 mm or
greater.
1] Fit the crown (a) and drive wheel (b) to the
motor.
2] Measure the length (L) between the end of
the drive wheel and the head end.
L
1]
(a)(b)
2]
2.1.2.Preparing the tube
1] Cut the tube to the required length.
2] Deburr the tube and remove the debris.
1] 2]
EN Sonesse 28 WF RTS
6Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved.
2.1.3.Assembling the drive-tube
1] Slide the drive into the tube. Insert the
wheel by aligning the wheel to the tube
profile. Insert the drive half way and then
slide the crown down the drive and insert
it in the tube. Finally, push the motor
inside the tube.
2] Not required, but if needed, fix the tube to
the drive with self-tapping screws or steel
pop rivets depending on the dimension (L).
1]
2]
L
2.1.4.Mounting the tube-drive assembly on the brackets
(a) Standard bracket.
(b) Drive plate for specific bracket.
NOTICE
For optimal radio reception, the motor
antenna should be kept straight and should be
positioned outside of headrail (if used).
(a) (b)
2.2.Wiring
PRECAUTION
To ensure electrical safety, this Class III motor
must be powered by a «SELV» voltage source
(Safety Extra Low Voltage).
Plug the battery with the motor supply cable.
CAUTION
Do not unplug the battery when the motor
works.
Sonesse 28 WF RTS EN
Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved. 7
2.3.Commissioning
NOTICE
Orange LED blinks continuously in setting mode.
Green LED blinks once when any order from paired remote is received.
2.3.1.Pre-programming the control point
Press the Up and Down buttons simultaneously
on the control point:
→The motorised product moves up and down and
the control point is temporarily programmed.
2.3.2.Checking the direction of rotation
Press the Up button on the control point:
a] If the motorised product rises, the direction of
rotation is correct: move onto Setting the end
limits [}7]
b] If the motorised product lowers, the direction
of rotation is incorrect: move onto the next step.
b1] Press the My button on the control point until
the motorised product moves up and down: The
direction of rotation has been modified and green
LED blinks 5 times.
b2] Press the Up button on the control point to
confirm the direction of rotation.
a]
b]
b1] b2]
ü
2.3.3.Setting the end limits
NOTICE
The end limits can be set in any order.
EN Sonesse 28 WF RTS
8Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved.
1] Press and hold the Up button to move the
motorised product to the desired up
position. If necessary, adjust the up
position using the Up or Down buttons.
2] To memorize the up limit: Press the My
and Down buttons simultaneously and
release once the motorised product
begins to move. The up limit is now
memorized and green LED blinks 5 times.
3] Press the My button when the motorised
product reaches the desired down
position. If necessary, adjust the down
position using the Up or Down buttons.
4] To memorize the down limit: Press the
My and Up buttons simultaneously and
release when the motorised product
begins to move. The down limit is now
memorized. The motorised product
moves up and will stop at its upper limit
and green LED blinks 5 times.
5] To confirm and complete limit
programming: Press and hold the My
button until the motorised product briefly
moves up and down. The end limits are
now recorded.
1] 2]
3]
5]
4]
2.3.4.Recording “Pairing” the control point
After recording the end limits:
Briefly press the control point Prog. button.
→The motorised product briefly moves up and
down to confirm pairing.
The control point is recorded “paired” to the
motorised product and green LED blinks 5 times.
PROG.
Sonesse 28 WF RTS EN
Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved. 9
2.4.Tips and advice on installation
2.4.1.Questions about the drive?
Observations Possible causes Solutions
The motorised product
does not operate.
External battery is low and
requires charge.
Charge the battery.
The control point battery is
low. LED doesn't light
when any button of a
paired control point is
pressed.
Check the battery and
replace it as required.
The control point is not
compatible or not
programmed. LED doesn't
light when any button of
control point is pressed.
Check the compatibility or
pair the control point as
required referring to
Adding/Deleting Somfy
control points [}18].
An obstacle hinders the
movement of the
motorised product. The
Red LED lights fixed on.
Remove the obstacle.
Drive position is out of the
end limits. Red LED blinks 2
times intermittently and
continually.
Proceed to Setting the
end limits [}7].
Motor is neither set nor
paired. Orange LED lights
fixed on.
Proceed to
Commissioning.
The thermal protection has
activated. LED blinks red
continuously.
Wait for the drive to cool
down (LED will switch off)
Motor is in setting mode.
Orange LED blinks.
Proceed to Setting the
end limits [}7].
EN Sonesse 28 WF RTS
10 Copyright© 2020 SOMFY ACTIVITES SA. All rights reserved.
Observations Possible causes Solutions
Proceed to Recording
“Pairing” the control
point [}8];
Disconnect and reconnect
the battery.
The motorised product
stops too soon.
The end limits are
incorrectly set.
Reset the end limits.
The motorised product has
exceeded recommended
weight limit.
Replace the motorised
product.
Battery is low. Charge the battery.
Setting is not allowed. The
drive moves briefly 3 times
in one direction and 3 times
in the other direction. Red
LED blinks 3 times and 3
times intermittently.
Maximum number of
control points reached.
Erase control points from
memory to add a new
control point referring to
Erasing control points
from memory [}12]
Maximum/minimum value
of the setting is reached.
Perform correct setting.
End limits are too close Readjust the end limits
referring to Readjusting
the end limits [}10].
2.4.2.Readjusting the end limits
CAUTION
Control point must be paired to the motorised product.
NOTICE
Orange LED blinks slowly until the new end limit is recorded.
Autres manuels pour Sonesse 28 WF Zigbee
3
Table des matières
Autres manuels SOMFY Entraînement CC
SOMFY
SOMFY Sonesse 40 RTS Manuel utilisateur
SOMFY
SOMFY Orea RTS Series Mode d’emploi
SOMFY
SOMFY Sonesse Ultra 50 Manuel utilisateur
SOMFY
SOMFY S&SO-RS100 io Manuel utilisateur
SOMFY
SOMFY Sonesse ULTRA 30 WF Zigbee Li-ion Manuel utilisateur
SOMFY
SOMFY Movelite DCT Manuel utilisateur
SOMFY
SOMFY ALTUS RTS Series Manuel utilisateur
SOMFY
SOMFY ilmo2 50 WT Manuel utilisateur
SOMFY
SOMFY MAESTRIA+ 50 RTS Manuel utilisateur
SOMFY
SOMFY Orea 50 WT Manuel utilisateur
SOMFY
SOMFY Sunea 40 Solar io Manuel utilisateur
SOMFY
SOMFY OXIMO BASIC WF RTS Manuel utilisateur
SOMFY
SOMFY mMotion Plus Manuel utilisateur
SOMFY
SOMFY sonesse 30 rts Manuel utilisateur
SOMFY
SOMFY ALTUS 40 RTS Manuel utilisateur
SOMFY
SOMFY HOME MOTION Orea WT Series Manuel utilisateur
SOMFY
SOMFY Compact Manuel utilisateur
SOMFY
SOMFY Sunea 40 RTS DC Manuel utilisateur
SOMFY
SOMFY Sonesse 40 Zigbee Manuel utilisateur
SOMFY
SOMFY S&SO-RS100 io Manuel utilisateur
Manuels Entraînement CC populaires d'autres marques
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces
Chamberlain Garog
Chamberlain Garog D Series Manuel utilisateur
Parker
Parker PDS Series Manuel utilisateur
Festo
Festo DGC G Series Guide de configuration
Binks
Binks QS-5012-1-CE Manuel utilisateur
