SolarEdge SE3680H Manuel utilisateur

Installation Guide

EV Charging Single Phase

Inverter

with SetApp Configuration

For Europe, APACand South Africa

Version 1.1

Disclaimers

Important Notice

No part of this document may be reproduced, stored in a retrieval system or

transmitted, in any form or by any means, electronic, mechanical, photographic,

magnetic or otherwise, without the prior written permission of SolarEdge Inc.

The material furnished in this document is believed to be accurate and reliable.

However, SolarEdge assumes no responsibility for the use of this material. SolarEdge

reserves the right to make changes to the material at any time and without notice. You

may refer to the SolarEdge web site (www.solaredge.com) for the most updated version.

All company and brand products and service names are trademarks or registered

trademarks of their respective holders.

Patent marking notice: see http://www.solaredge.com/patent

The general terms and conditions of delivery of SolarEdge shall apply.

The content of these documents is continually reviewed and amended, where

necessary. However, discrepancies cannot be excluded. No guarantee is made for the

completeness of these documents.

The images contained in this document are for illustrative purposes only and may vary

depending on product models.

Emission Compliance

This equipment has been tested and found to comply with the limits applied by the

local regulations.

These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, you are encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Disclaimers 1

EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance may void the user’s authority to operate the equipment.

EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

2 Emission Compliance

Support and Contact Information

If you have technical problems concerning SolarEdge products, please contact us:

Support Center: https://www.solaredge.com/service/support

Country Phone E-Mail

Australia (+61) 1800 465 567 support@solaredge.net.au

APAC (Asia Pacific)(+972) 073 240 3118 support-

asia@solaredge.com

Belgium (+32) 0800-76633 support@solaredge.be

China (+86) 21 6212 5536 support_

china@solaredge.com

DACH & Rest of Europe (+49) 089 45459730 support@solaredge.de

France (+33) 0806 700409 support@solaredge.fr

Italy (+39) 0422 053700 support@solaredge.it

Japan (+81) 03 6262 1223 support@solaredge.jp

Netherlands (+31) 0800 7105 support@solaredge.nl

New Zealand (+64) 0800 144 875 support@solaredge.net.au

Republic of Ireland (+353) 1800 901 575 support-uk@solaredge.com

United Kingdom (+44) 0800 0281183

US & Canada (+1) 510 498 3200 ussupport@solaredge.com

Greece (+49) 89 454 59730

support@solaredge.com

Israel (+972) 073 240 3122

Middle East &Africa (+972) 073 240 3118

South Africa (+27) 0800 982 659

Turkey (+90) 216 706 1929

Worldwide (+972) 073 240 3118

Before contact, make sure to have the following information at hand:

Model and serial number of the product in question.

The error indicated on the Inverter SetApp mobile application or on the monitoring

platform or by the LEDs, if there is such an indication.

System configuration information, including the type and number of modules

connected and the number and length of strings.

Support and Contact Information 3

EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

The communication method to the SolarEdge server, if the site is connected.

The inverter software version as appears in the status screen.

Revision History

Version 1.1, May 2019 - editorial changes

Version 1.0 , March 2019 - first release

EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

4 Support and Contact Information

Contents

Disclaimers 1

Important Notice 1

Emission Compliance 1

Support and Contact Information 3

HANDLING AND SAFETY INSTRUCTIONS 7

Safety Symbols Information 7

IMPORTANTSAFETYINSTRUCTIONS 8

Chapter 1: Introducing the SolarEdge Power Harvesting System 11

Power Optimizer 12

EV Charging Single Phase Inverter 12

Monitoring Platform 13

Installation Procedure 14

Installation Equipment List 14

Inverter Transport and Storage 15

EV Charging Safety Instructions 16

Chapter 2: Installing the Power Optimizers 17

Safety 17

Installation Guidelines 18

Step 1: Mounting the Power Optimizers 20

Step 3: Connecting Power Optimizers in Strings 21

Step 4: Verifying Proper Power Optimizer Connection 21

Chapter 3: Installing the Inverter 23

Inverter Package Contents 23

Identifying the Inverter 23

Inverter Interfaces 23

Mounting the Inverter 27

Chapter 4: Connecting the AC and the Strings to the Connection Unit 31

Selecting a Residual Current Device (RCD) 34

Chapter 5: Activating, Commissioning and Configuring the System 35

Step 1: Activating the Installation 35

Step 2: Commissioning and Configuring the Installation 36

Step 3: Verifying Proper Activation and Commissioning 40

Viewing System Status 41

Reporting and Monitoring Installation Data 48

Chapter 6: Setting Up Communication 51

Communication Options 51

Communication Connectors 53

Removing the Inverter Cover 54

Support and Contact Information 5

EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

Removing the Connection Unit Cover 54

Creating an Ethernet (LAN) Connection 55

Creating an RS485 Bus Connection 58

Verifying the Connection 59

Appendix A: Errors and Troubleshooting 61

Identifying Errors 61

EV Charger-related Troubleshooting 62

Power Optimizer Troubleshooting 65

Appendix B: Mechanical Specifications 67

Appendix C: Replacing and Adding System Components 68

Fuse Replacement 68

Replacing an Inverter 69

Replacing the Connection Unit 70

Appendix D: SafeDC™ 73

Technical Specifications - EV Charging Single Phase Inverter (Europe & APAC) 74

Inverter Specifications 74

Default Trip Limits and Times According to IEEE1547 77

EV Charger and EV Charger Cable Specifications 78

EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

6 Support and Contact Information

HANDLING AND SAFETY INSTRUCTIONS

During installation, testing and inspection, adherence to all the handling and safety

instructions is mandatory. Failure to do so may result in injury or loss of life and

damage to the equipment.

Safety Symbols Information

The following safety symbols are used in this document. Familiarize yourself with the

symbols and their meaning before installing or operating the system.

WARNING!

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, could result in injury or loss of life. Do not proceed

beyond a warning note until the indicated conditions are fully understood and

met.

CAUTION!

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, could result in damage or destruction of the

product. Do not proceed beyond a caution sign until the indicated conditions

are fully understood and met.

NOTE

Denotes additional information about the current subject.

IMPORTANTSAFETYFEATURE

Denotes information about safety issues.

Disposal requirements under the Waste Electrical and Electronic Equipment (WEEE)

regulations:

NOTE

Discard this product according to local regulations or send it back to SolarEdge.

HANDLING AND SAFETY INSTRUCTIONS 7

EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

IMPORTANTSAFETYINSTRUCTIONS

SAVETHESEINSTRUCTIONS

WARNING!

When using electric products, basic precautions should always be followed,

including the following. This manual contains important instructions that shall

be followed during installation, operation and maintenance of the unit.

a. Read all the instructions before using this product.

b. This device should be supervised when used around children.

c. Do not put fingers into the electric vehicle connector.

d. Do not use this product if the flexible power cord or EV cable is frayed, has

broken insulation, or any other signs of damage.

e. Do not use this product if the enclosure or the EV connector is broken,

cracked, open, or shows any other indication of damage.

1. An insulated grounding conductor that is identical in size, insulation

material, and thickness to the grounded and ungrounded branch-circuit

supply conductors, except that it is green with or without one or more

yellow stripes, shall be installed as part of the branch circuit that supplies the

device or system.

2. The grounding conductor described in item 1 shall be grounded to earth at

the service equipment or, when supplied by a separately derived system, at

the supply transformer.

WARNING!

The inverter cover must be opened only after switching the inverter ON/OFF/P

switch located at the bottom of the inverter to OFF. This disables the DC voltage

inside the inverter. Wait five minutes before opening the cover. Otherwise, there

is a risk of electric shock from energy stored in the capacitors.



EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

8 IMPORTANTSAFETYINSTRUCTIONS

WARNING!

Before operating the inverter, ensure that the inverter AC power cable and wall

outlet are grounded properly. This product must be connected to a grounded,

metal, permanent wiring system, or an equipment-grounding conductor must

be run with the circuit conductors and connected to the equipment grounding

terminal or lead on the product.

WARNING!

Opening the inverter and repairing or testing under power must be performed

only by qualified service personnel familiar with this inverter.

WARNING!

Do not touch the PV panels or any rail system connected when the inverter

switch is ON, unless grounded.

WARNING!

SafeDC complies with IEC60947-3 when installing the system with a worst case

SafeDC voltage (under fault conditions) < 120V.

The worst case voltage is defined as: Voc,max+ (String Length-1)*1V, where:

Voc,max = Maximum Voc (at lowest temperature) of the PV module in the

string (for a string with multiple module models, use the max value)

String Length = number of power optimizers in the string

CAUTION!

This unit must be operated according to the technical specification datasheet

provided with the unit.

CAUTION!

HEAVY OBJECT. To avoid muscle strain or back injury, use proper lifting

techniques, and if required - a lifting aid.

NOTE

Use PV modules rated according to IEC 61730 class A.

IMPORTANTSAFETYINSTRUCTIONS 9

EV Charging Single Phase Inverter Guide MAN-01-00583-1.1

Autres manuels pour SE3680H

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SolarEdge Onduleur

SolarEdge

SolarEdge StorEdge SE10K-RWS Manuel utilisateur

SolarEdge

SolarEdge EV Series Manuel utilisateur

SolarEdge

SolarEdge StorEdge Solution with Backup Manuel utilisateur

SolarEdge

SolarEdge storedge Manuel utilisateur

SolarEdge

SolarEdge StorEdge SE5K Manuel utilisateur

SolarEdge

SolarEdge Home Hub Inverter Three Phase Manuel utilisateur

SolarEdge

SolarEdge Dry-Contact switch Manuel utilisateur

SolarEdge

SolarEdge SE9KUS Manuel utilisateur

SolarEdge

SolarEdge SE K Series Manuel utilisateur

SolarEdge

SolarEdge SE K Series Manuel utilisateur

SolarEdge

SolarEdge BI-EU1P Manuel utilisateur

SolarEdge

SolarEdge StorEdge SE7600A-USS Manuel utilisateur

SolarEdge

SolarEdge storedge Manuel utilisateur

SolarEdge

SolarEdge SEK-AU I Series Manuel utilisateur

SolarEdge

SolarEdge StorEdge SE5000-xxS0 series Manuel utilisateur

SolarEdge

SolarEdge SE8000H-AU Manuel utilisateur

SolarEdge

SolarEdge SE8k Manuel utilisateur

SolarEdge

SolarEdge Power Optimizer Manuel utilisateur

SolarEdge

SolarEdge SE3000H-US Manuel utilisateur

SolarEdge

SolarEdge SE K Series Manuel utilisateur

SolarEdge

SolarEdge Energy Bank Manuel utilisateur

SolarEdge

SolarEdge storedge Manuel utilisateur

SolarEdge

SolarEdge SE3K Manuel utilisateur

SolarEdge

SolarEdge 2.2KW Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur