Smoke Guard M200 Manuel utilisateur

Model 200 & 400 |

Installation Manual

Smoke Curtain

287 N. Maple Grove. Boise, ID 83704

P. (800) 574-0330 F. (208) 639-7851

info@smokeguard.com

Doc #2401 – M200/M400 Installation Manual Rev. 9

Contents

1.0 – Introduction ............................................................................................................................................................. 4

2.0 – System Overview...................................................................................................................................................... 6

2.1 – Major Components .................................................................................................................................................... 6

2.2 – Optional Components ................................................................................................................................................ 7

3.0 – Install Preparation.................................................................................................................................................... 8

3.1 – Verify Field Preparation ............................................................................................................................................. 8

3.2 – Preparing the Housing for Mounting ....................................................................................................................... 10

4.0 – Mounting the Housing and Auxiliary Rails ............................................................................................................. 11

4.1 – Installing the Mounting Plate................................................................................................................................... 11

4.2 – Mounting the Housing ............................................................................................................................................. 12

4.3 – Installing the Auxiliary Rails ..................................................................................................................................... 13

5.0 – Installing the Screen............................................................................................................................................... 15

5.1 – Installing the Screen................................................................................................................................................. 15

5.2 – Attaching the Extension Springs (M400 only).......................................................................................................... 18

5.3 – Installing the Screen Rewind Switch ........................................................................................................................ 19

6.0 – Testing and Adjusting............................................................................................................................................. 20

6.1 – Testing the Installation............................................................................................................................................. 20

6.2 – Anchoring the Magnets............................................................................................................................................ 21

7.0 – Finishing the Installation ........................................................................................................................................ 22

7.1 – Preparing the Unit for Wiring................................................................................................................................... 22

7.2 – Installing the Dust Cover .......................................................................................................................................... 22

7.3 – Wiring....................................................................................................................................................................... 23

7.4 – Setting the Unit in a Ready State ............................................................................................................................. 24

7.5 – Final Testing ............................................................................................................................................................. 25

8.0 – Troubleshooting ..................................................................................................................................................... 26

8.1– Spotting an error....................................................................................................................................................... 26

8.2– Troubleshooting the M200 and M400 without battery............................................................................................ 26

8.3 – Troubleshooting the M400 with battery.................................................................................................................. 27

8.4 – Error Codes – M400 with Battery............................................................................................................................. 28

8.5 – Solutions Guide ........................................................................................................................................................ 29

9.0 – Contact Smoke Guard ............................................................................................................................................ 31

10.0 – Glossary.................................................................................................................................................................. 32

11.0 – Suggested Anchors................................................................................................................................................. 34

Doc #2401 – M200/M400 Installation Manual Rev. 9

1.0 – Introduction

This is the official installation manual for the Model 200 and 400 Smoke Curtains from Smoke Guard,

Inc.

NOTE: This model shows a Model 400 (without a backup battery). Installation of the Model 200 is identical

but it does not have a door closer mechanism or door springs.

The Smoke Guard Models 200 & 400 Smoke Curtains (M200/M400) are motorized smoke protection systems

housed above an elevator. The M200 & M400 systems are rated to UL 1784 according to the requirements of

smoke and draft control assemblies defined in NFPA 105.

The smoke detector or other initiating device is part of the building smoke and fire alarm system and not a

component of the Smoke Guard system. In the event of an alarm, the initiating device signals the controller to

activate a DC motor as well as a damper and clutch (model dependent) to deploy a protective curtain. The

curtain unrolls to the floor with the curtain magnets adhering to either the elevator frame or auxiliary rails to

seal the opening. When not in use the M200/M400 is retracted into a housing unit which maintains the aesthetic

of the facility in which it is installed.

The system will also deploy in the event of a sustained power loss, with the exception of the M400 when

optioned with a battery for backup power. This can prevent fault deployments in the event of AC power loss.

However, the battery is for emergencies only.

Installation of the Smoke Guard system requires a moderate amount of construction and electrical experience as

well as a variety of tools and hardware, both standard and specialty. Installers should be comfortable drilling

through various materials (metal, sheetrock, wood, etc.), utilizing anchors appropriate for the backing material,

using a hand riveter, and terminating low voltage wires. Below is a list of tools and hardware required in

addition to the material supplied by Smoke Guard:

•25-foot tape measure

•Permanent marker

•Portable hand drill or driver

•Portable angle-head drill or attachment (for hard-lid installations)

•Drill bits (1/8” for rivets, remaining sizes depend on anchors utilized)

•#2 Philips bit

•Flat and Philips head screwdrivers

•Hand riveter

•Chalk line

•4-foot magnetic level

•Torpedo level

•Tin snips

•Portable bandsaw

•Wire strippers

•Utility knife

•5/16” and 7/16” combination wrenches

•3/32”, 1/8”, 5/32”, 5/16” ball head hex wrenches

•Grounded extension cord

Doc #2401 – M200/M400 Installation Manual Rev. 9

•Screen mounting brackets (J-hooks, available for purchase from Smoke Guard)

•Mounting plate anchors suitable for backing (qty. 6, see section 11 for suggested anchors)

•Plastic shims for leveling housing

•Rail backer anchors suitable for backing (qty. 10, see section 11 for suggested anchors)

Installation should occur after the installation of the elevator frame and surrounding drywall, but prior to ceiling

installation and any painting around the elevator.

NOTE: Follow applicable safety procedures during installation, including the appropriate use of any personal

protective equipment (e.g. hard hat, safety goggles, gloves, etc.). Exercise caution when using a ladder or

stepladder and ensure you get assistance and use proper lifting techniques when carrying and mounting the

housing.

Doc #2401 – M200/M400 Installation Manual Rev. 9

2.0 – System Overview

The M200/M400 Smoke Curtain is a motorized smoke protection system housed in the ceiling of a building.

The system uses a DC motor to deploy a specialized curtain into a strategic location. When not in use, the

M200/M400 is retracted into a housing unit which maintains the aesthetic of the facility in which it is installed.

Figure 1– The M200/M400 installed

2.1 – Major Components

Smoke Detector:The local smoke detector is the recommended initiating device for the M200/M400.

AC Line In:The M200/M400 connects to the building 120 VAC for primary power. When optioned with a

backup battery the M400 can also operate on 240 VAC.

Doc #2401 – M200/M400 Installation Manual Rev. 9

Housing:The M200/M400 housing contains the control, drivetrain, and screen assembly (when retracted). The

dust cover and junction box are integral parts of the housing.

Mounting Plate (not shown):The mounting plate attaches directly to the backing material above the elevator

and provides the mounting interface for the housing.

DuraNet™ Screen Assembly: The transparent screen assembly forms the main smoke protection barrier from

the elevator shaft and allows visibility from the car onto the landing

Kevlar® Cables: The cables connect the screen threshold pulleys to the drivetrain in the housing to allow the

screen to retract and deploy.

Flexible Magnetic Edge: The magnets on either side of the screen assembly secure the screen to the auxiliary

rails or elevator frame. These magnets also allow for push through manual egress if necessary.

Screen Rewind Switch: The Screen Rewind Switch (SRS) allows egress from either side of the screen. When

pressed the screen will temporarily retract into the housing before redeploying.

Auxiliary Rail: Auxiliary rails provide a surface for the screen magnets to adhere to. The M400 can be

optioned to adhere directly to the elevator frame, which does not require the use of full length

auxiliary rails. In this configuration the auxiliary rails can also be used as stub rails to bridge the gap

from the housing to the elevator frame.

Auxiliary Rail Backer: If auxiliary rails are used, the backer is attached to the mounting surface during install.

Installation Kit (not shown): A variety of installation components is included with each unit. This kit includes

a roll of Kapton® tape for securing the SRS wiring, a bag of hardware for securing the screen and

housing, a pair of housing door clips for holding the door closed before permanent power is attached.

End of Line Diode (not shown): The end of line (EOL) diode allows for monitoring the integrity of the

initiating device circuit. The EOL diode is required for all installations, see the electrical guide for

more information. The EOL diode is shipped inside the housing junction box.

2.2 – Optional Components

The M400 may be shipped with the following optional components:

•Wall Activation Switch

•Controller Backup Battery

Doc #2401 – M200/M400 Installation Manual Rev. 9

3.0 – Install Preparation

3.1 – Verify Field Preparation

Prior to installing the Smoke Guard system, the general contractor prepares the site for installation.

Housing clearance – For each housing the general contractor provides a clearance above the elevator:

•Unobstructed, wall plumb, with no distortions

•No more than 10 feet (12 feet for M400 units ordered as such) from the floor to the bottom of the

housing

•At least 10 inches vertical and 12 inches projected from the mounting surface

•At least 2 inches wider than the housing, centered over the elevator door

•Mounting height marked with a chalk line

•Ceiling and grid removed from housing area

•Backing extending the full width and height of the clearance

Doc #2401 – M200/M400 Installation Manual Rev. 9

Curtain clearance – For each housing the general contractor provides a clearance on the landing side of the

elevator:

•Extending from the bottom of the housing to the floor along the full screen assembly width

•Centered over the hoistway frame

•Unobstructed, wall plumb, with no distortions

•Free of all obstructions and projections that exceed the housing return depth, including the elevator

position indicators, signs, and hall call stations

•Includes clearance for door swing; 7-1/4 inches

•With 2 inch wide backing for auxiliary rail backers extending the full height

Doc #2401 – M200/M400 Installation Manual Rev. 9

3.2 – Preparing the Housing for Mounting

The screen assembly ships inside the housing, remove carefully to avoid damaging the screen and/or the

housing components.

NOTE: The door closer extension springs (M400 only) and the up-limit switch are not attached in their

operating positions as shipped. This allows for safe removal of the screen assembly. They will be installed to

their final location later in the installation process.

Removing the screen and mounting plate from the housing:

1. With the housing return side on the saw horses, remove the dust cover

2. Push the door open and gently roll the screen out through the housing door

3. Using the 5/32” hex wrench loosen and remove the machine screws holding the mounting plate to the

housing and remove the mounting plate

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Smoke Guard Équipements de sécurité

Smoke Guard

Smoke Guard M1000 Manuel

Smoke Guard

Smoke Guard 600 Manuel utilisateur

Manuels Équipements de sécurité populaires d'autres marques

Innova

Innova Xtirpa Mode d’emploi

bolle SAFETY

bolle SAFETY B810 Manuel utilisateur

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manuel utilisateur

Hiltron security

Hiltron security POWER8E Mode d’emploi

Hatco

Hatco B-950P Manuel utilisateur

Sitec

Sitec TX MATIC Manuel utilisateur

TEUFELBERGER

TEUFELBERGER GRIP 12 Manuel utilisateur

MSA

MSA PremAire System Manuel utilisateur

AMC

AMC 1022M Series Manuel utilisateur

Trinity

Trinity CASS S3 Manuel utilisateur

CMC

CMC Helitack HotSeat Manuel utilisateur

Force

Force P-35 Manuel utilisateur

ACM

ACM SAFETY D200 Manuel du produit

Honeywell

Honeywell Miller H-Design DuraFlex Manuel de l'opérateur

ROCK

ROCK P-451 AS Manuel utilisateur

Power first

Power first 2XYR7A Manuel de service

SCHUBERTH

SCHUBERTH SHP 28-C Manuel utilisateur

Trango

Trango CINCH Manuel utilisateur