SmartTrike Xtend Mg+ Manuel utilisateur
Max load 50kg
Ages 3-7yrs
Designed to fit riders with measurements
Inseam: 47-59cm , Height: 95-125cm
-1-
www.youtube.com/user/smartTrikeOcial
www.smarTrike.com
age 3 - 4yrsBalance
age 4 - 6yrsPedal
Teach them to ride
Watch them go...
age 6 - 7yrs
Bike
See them fly!
20701A
™
-2-
17mm
6mm
5mm
2
Assembly parts
1
L
R
15mm
BEB1503 BEB1101
BEB1002
BEB1024201BEB1008104 BEB1013201 BEB1004102 BEB1213101
BEB1011201 BEB1509101 / BEB1020201BEB1508101
BEB1025201 BEB1026201 BEB1027201
-3-
NOTE: This information is only available on the bicycle itself.
Each bicycle has a Recovery Code stamped into the frame. The Recovery Code
.can be found on the bottom of the crank housing as shown
NOTE: This information is available only on the bicycle.
As shown in the image, our bicycle has the production date
code stamped into its body (model / STB / month /year).
Owner’s Bicycle Identification Record
X
X
X
X
X
X
X
X
X
X
X
XX
Under the body tube
3 Steps to Adjust the Bike to the Rider
1.
2.
3.
Assemble the bike. Make sure the tyres are well inflated.
Riders must have at least 2.5cm 1 between their crotch and the seat when standing with
feet shoulder-width apart and flat on the ground
Make necessary adjustments to the bike so the rider’s leg-length is at least 2.5cm higher
than the bike's seat 3 .
2 .
-4-
The Owner’s Responsibility
Warning and Safety Information
Meanings of Warnings:
As small parts exist, a CHOKING HAZARD exists. Not recommended for small children.
under 3 years.
Adults need to assemble the bicycle.
The replacement of the handlebar hand grip or tube end plugs must be done if it is
damaged. This is necessary as bare tubes could cause injury. All the products with
capped handlebar ends need to be regularly checked to ensure that there is ample
protection for the ends of the handlebars.
The replacement forks should have the same rake and tube inner diameter just like the
original product.
No motor should be added to the product.
The product should not be towed or pushed.
No modification should be made to the product.
Any worn or broken parts must be replaced immediately.
Discontinue use if any part does not function properly.
WARNING: Only one rider must ride this bicycle at a time for general transportation and
recreational purpose. It has not been designed to withstand the abuse of jumping or stunting.
NOTE: Frequently check that all the components and fasteners are properly tightened.
In case the bicycle was purchased in an assembled state, it is the owner’s responsibility, before
riding it for the first time, to ensure it has been assembled and adjusted exactly as written in this
manual, and any “Special Instructions” provided and to ensure all components and fasteners are
properly tightened.
The bicycle was unassembled while purchasing, it is the responsibility of the owner to follow all the
assembly and adjustment instructions carefully just as they are written in this manual. Take care of
any “Special Instructions” that have been supplied and ensure that all the components and fasten-
ers are properly tightened.
NOTE:
If the product is assembled, please proceed to these sections:
Testing Stem and Handlebar Tightness.
Testing the seat- Post Clamp Tightness.
This symbol is highly crucial. Carefully see the word “CAUTION” or “WARNING” which follows
it. The word “CAUTION” is provided before mechanical instructions. In case you do not obey these
instructions carefully, mechanical damage or failure of a part of the bicycle can take place.
The word “WARNING” is given before personal safety instructions. If you do not obey these
sensitive instructions, injury to the person riding or to others can take place.
-5-
Rules of the Road
WARNING: If the rider fails to obey the following “Rules of the Road”, he can suer
from injury or others could be hurt.
Obey all trac rules, regulations, signs, and signals.
You must wear a bicycle helmet that meets the local standard and the local safety
standards.
Make sure to wear shoes while riding.
Ride on the correct side of the road, in a straight line and in a single file.
Bikes not intended for use on the public roads.
Avoid riding the bike at night, dusk, dawn and any other time when the visibility is
poor.
Reflectors: Do not ride the bicycle in case the reflectors are not installed correctly,
damaged, or missing, for your own safety. Ensure the front and rear reflectors are
vertical. Make sure that the visibility of the reflectors is not blocked by clothing or
other articles. Clean the reflectors as necessary with soap and a damp cloth
because dirty reflectors do not work well.
Use extra caution in wet weather:
Ride the bike slowly on damp surfaces as the tyres could slide easily.
Allow increased braking distance while riding in wet weather.
Avoid these hazards to prevent loss of control or damage to your wheels:
Be careful of drain grates, soft road edges, sand or gravel, potholes or ruts, wet
leaves, or uneven paving.
Make sure to cross railroad tracks at a proper angle to prevent losing control of
the bike.
Unsafe actions must not be conducted while riding.
Passengers must not be carried while riding the bicycle.
Do not carry any items or attach other things to your bicycle that could obstruct
your vision, hearing or control.
Do not ride with both your hands o the handlebar of the bike.
Do not fit a luggage carrier and (or) a child seat to the bicycle.
-6-
Componenti di Assemblaggio
NOTA: Tutte le caratteristiche,
i componenti, e gli accessori,
non sono inclusi in tutti i modelli.
1
4
6
7
8
8
10 11
20
21
14
15
16
16
15
17
18
13
12
19
23
24
25
22
26
26
26
26
27
3
5
9
2
28
-7-
Fitting the
No.No.
1
Description
Frame
2Fork
3Handlebar
4Grips (x2)
5Handlebar Stem
6Seat
7Seat Post
8Clamp
9Head Set Bearings
10 Right Pedal
20 Chain
21 Chain Cover
Balance Bike System
22
23
25
26
27
28
24
Bell
Reflectors
11 Left Pedal
12
Description
Wheel Retainer (x2)
Balance Bike System Bolts (x3)
13 Front Wheel Nut (x2)
15 Tyre (x2)
16 Tube (x2)
14 Front Wheel Assembly
17 Rear Wheel Assembly
18 Front brake disc
Rear brake disc
Fender
19
Parts Assembly List
Back Wheel Nut (x2)
Assembly
Follow all the instructions completely and carefully.
Please read the entire manual through before starting
assembly or maintenance.
In case you are not confident with assembling this unit,
please refer to a local bike shop.
WARNING: Keep small components away from children during the assembly
process.
NOTE: All of the directions (right, left, front, rear, etc.) provided in this
manual are as seen by the rider riding the bicycle.
Do not dispose of the carton or other packaging parts until the assembly of
the bicycle is complete. It can prevent accidentally discarding components
of the bicycle.
Hand Brake (x2)
-8-
NOTE: This information is only available on the bicycle itself.
Each bicycle has a Recovery Code stamped into the frame. The Recovery Code
.can be found on the bottom of the crank housing as shown
Handlebar and Stem Installation
Adjusting the handlebar
WARNING: To prevent steering system damage and
possible loss of control, the “MIN-IN” (minimum
insertion) mark , on the stem must be below the top
of the locknut B .
NOTE:
Remove plastic cap C from the end of
the stem D .
A
WARNING: If the handlebar clamp in not tight enough, the handlebar can slip in the stem. This
can cause damage to the handlebar or stem, and can cause loss of control.
2
5mm 5mm
6mm
If necessary, loosen the handlebar clamp nut/screw F and rotate handlebar into
a comfortable riding position (fig A, B).
NOTE: Do not over tighten. See torque
table for recommended torque.
fig B
fig A
D
E
C
A
B
STEPS:
1. Insert the stem D into the fork (fig A).
2. Point the stem towards the the front section of
the bike.
3. Streamline the stem with the front fork and
tighten the stem bolt securely.
4. Tighten the stem bolt E just enough to hold it
in place.
1
F
3
F
-9-
NOTE: This information is only available on the bicycle itself.
Each bicycle has a Recovery Code stamped into the frame. The Recovery Code
.can be found on the bottom of the crank housing as shown
5mm
A
BC
Seat Bolt Mount
Use a 5mm Allen key for adjusting the height of the
seat as per the drawing on page number 3.
Pull the seat out as per the required height.
Use the 5mm Allen key for locking the mechanism
back.
After assembling the seat,
press down on the seat to
make sure it is well
reinforced.
C.
B.
A.
Seat Installation
ATTENTION: Afin d'empêcher
que la selle ne soit trop lâche et
de prévenir une éventuelle perte
de contrôle, la marque A
"MIN-IN" (insertion minimale)
sur le support de la selle est
placée en-dessous de la partie
supérieure du tube de la selle B
A
B
C
Selon les normes européennes,
n'insérez pas la selle au-delà de la
marque supérieure (marque
d'illustration C )
1
2
3
-10-
Assembly
Step 1:
Step 2:
Turn the bicycle in upside down manner so the fork is upwards.
BA
Insert the wheel according to the arrow.
Step 3:
A. Remove the screw and keep it for the next step.
B. Attach the fender as described and fasten with the screw.
6mm
Autres manuels SmartTrike Vélo
SmartTrike
SmartTrike 607 Manuel utilisateur
SmartTrike
SmartTrike 500 Manuel utilisateur
SmartTrike
SmartTrike 550 Manuel utilisateur
SmartTrike
SmartTrike Zoom 319 Manuel utilisateur
SmartTrike
SmartTrike 650 Manuel utilisateur
SmartTrike
SmartTrike 400 Manuel utilisateur
SmartTrike
SmartTrike splash Manuel utilisateur
