SmartRG SR616ac Manuel utilisateur
Quick Start Guide
SR616ac
This Quick Start Guide shows you how to set up and start using your new gateway.
Installation
1. Connect one end of the included phone cable to the DSL port on the gateway and connect the other end to the
wall jack.
2. Connect one end of an Ethernet cable to a LAN port of the gateway and connect the other end to your PC.
3. Plug the power adapter into the wall outlet and connect the other end of it to the Power port of the gateway.
4. Turn on the unit by pressing the On/Off button on the left side of the gateway.
Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to com-
plete before you can begin using your Internet applications (browser, email, etc.).
Notes:
lIf you use 3G WAN service, connect the 3G USB data card to the USB port of the gateway. If you use the Ethernet
uplink, connect to the WAN port with an Ethernet cable.
lYou cannot use the xDSL uplink, 3G WAN service, and Ethernet uplink at the same time.
If you are unable to connect to the Internet, confirm that all connections are in place and the gateway is turned on.
DSL TEL LAN WAN USB
DC/IN
COAX
Modem
Line
RJ11
Phone
Phone
3G USB Data
Card / LTE
RJ45
1a
1c
1b
2
3
Phone Phone
3
LED INDICATORS
The LEDs on the front of the SR616ac gateway can help you
understand the current state of your adapter.
Legend: White White blinking Red Green Green blinking
LED Action Explanation
All LEDs
except
those
listed below
Feature enabled &/or working correctly
Data being transferred
POWER Unit is booting up & preparing for use. When the unit is ready, the light changes to green.
Device powered on and ready to use.
WAN WAN connection active
LAN LAN connection active
Data being transferred
Quick Gateway Configuration
Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small cir-
cular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into
the hole, press the Reset button for 1 second, and then release the button. The system reboots and returns to the fact-
ory defaults.
Logging in to your gateway
To change the settings on your gateway, you must log in to the gateway's interface. Make sure that you have completed
the steps in "Installation" on page2 before you begin.
1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.
5
2. Enter the factory default credentials shown below and click Log In.
User Name: admin Password: admin
Note: Your service provider may use other settings. Contact your provider for details.
Configuring the WAN manually
If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer 2 Interface and WAN Service
sections of the SmartRG SR616ac Gateway User Manual to manually establish a connection.
WiFi Setup
Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow
the instructions for the applicable method. The default settings work for most situations.
1. In the left menu, click Wireless and then click 2.4 GHz Band or 5 GHz Band. The fields are the same for both
options. The wireless radio is enabled by default.
2. Continue with the steps for the method you prefer.
7
WPS Method
If the device you wish to connect to the Internet via your gateway supports the WPS secure Wi-Fi connection method,
follow these steps.
1. In the left navigation bar, click Wireless, then click the band that you want to configure, and then click Secur-
ity.
2. In the Enable WPS field, make sure that Enabled is selected, and then click Apply/Save to save your change.
3. On the left side of the gateway’s exterior:
a. Activate the desired band by pressing 2.4 GHz or 5 GHz briefly on the rocker switch.
b. Activate WPS by pressing the desired band button and holding it down for 7 seconds.
4. Within 2 minutes, activate WPS on the 3rd party device to which you wish to connect. The device may have a
push button on its exterior that you can press, or a clickable button on a software interface. To learn how to use
the WPS feature on your client device, refer to its documentation.
Your device should now be connected to your gateway wirelessly using WPS. If you encounter problems with the WPS
setup such as connection failure, refer to your client device for further instructions.
Manual Method
Set up your gateway’s parameters first, then follow these steps.
1. In the left menu, click Wireless and then the band that you want to configure.
2. Click Security and scroll down to the Manual Setup AP section.
3. If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You
will need this ID for step 8.
4. Select the desired Network Authentication. Make sure that the host devices you intend to use support the
selected authentication type.
5. Choose a WPA Passphrase and type it in to this field. You will need this passphrase for step 8.
6. Select any desired encryption preferences in the lower three fields.
9
7. Click Apply / Save.
8. Follow the WiFi connection instructions provided with your client device to connect to the router. Use the SSID
name you selected in Step 3 and enter the same passphrase that you entered in step 5 to set up the connection
on your client device.
Autres manuels pour SR616ac
1
Table des matières
Autres manuels SmartRG Routeur réseau
SmartRG
SmartRG SR320n Manuel utilisateur
SmartRG
SmartRG SR505n Manuel utilisateur
SmartRG
SmartRG SR512nm Manuel utilisateur
SmartRG
SmartRG SR630N Manuel utilisateur
SmartRG
SmartRG SR506n Manuel utilisateur
SmartRG
SmartRG DB120-WL Manuel utilisateur
SmartRG
SmartRG SR510n Manuel utilisateur
SmartRG
SmartRG SR655ac Manuel utilisateur
SmartRG
SmartRG SR515ac Manuel utilisateur
SmartRG
SmartRG SR310N Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité