Smarter Home Platform Storage Rack 4' x 8' Manuel utilisateur
Platform Storage Rack
4’ x 8’
INSTALLATION MANUAL
4’ x 8’
Safety Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MyLifter Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Platform Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 1: Assemble Platform Overhead Storage Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Step 2: Install Smart Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 3: Install MyLifter Hoists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Step 4: Install Power Adapters and Cable Management Clips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 5: Attach Platform To MyLifters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table of Contents
1. This is a DO IT YOURSELF project. Read and follow the installation instructions carefully. Failure to follow instructions
could result in property damage, serious injury or death. If you have any questions or concerns about the quality of your
ceiling structure discontinue installation and consult a structural engineer.
2. Do not attempt to install any SmarterHome product or device without a basic understanding of these installation
instructions. If you are not confident locating and anchoring items to ceiling joists do not attempt this installation.
3. Do not exceed the stated weight limits noted on the platform overhead storage rack. Deflection of the storage rack can
happen as it reaches maximum weight load. The weight limit is based on a statically loaded storage rack that is anchored
to a wood framed garage. This system is not compatible if your house in constructed using metal studs.
4. Load the overhead storage rack evenly being sure to place heavier objects closer to the vertical uprights and the lighter
objects closer to the center.
5. Routinely inspect the storage rack to ensure rivets and wire decking are properly seated.
Safety Overview
2
WARNING
Lifting capacity (motorized) = 320 lbs | Weight Limit (non-motorized/static) = 600 lbs.
MyLifter Safety
3
When using the the MyLifter and related storage accessories:
• Do NOT use the MyLifter to lift people or animals.
• Do NOT climb or hang on the storage rack.
• Do NOT lift items while hands or other body parts are near the MyLifter device,
lifting cables, storage accessories, etc.
• Do NOT stand under the MyLifter or any items that have been lifted by the MyLifter.
• Do NOT use the MyLifter to lift or lower items over people or animals.
• Do NOT exceed the lifting capacity of the MyLifters.
• Do NOT attempt to install/secure lifters to angled ceilings or walls. MyLifter units
are designed to be secured to flat ceilings only.
• Do NOT install in any manner other than as specified in instructions.
• Do NOT attempt to lift unbalanced loads. Always balance items/loads before lifting.
Inspect the MyLifter Cable(s)
• Inspect the MyLifter cable(s) often/before each use to ensure it is properly seated on the pulley wheel. If the cable is
tangled, damaged, or bent, stop using your MyLifter device immediately.
Avoid Electric Shock
• To avoid risk of electric shock and/or other potential injury DO NOT disassemble or open any SmarterHome device. All
SmarterHome products are designed for indoor use only. Failure to follow these safety instructions could result in
property damage, serious personal injury, or death.
What’s in the Box (Drawings below are not shown to scale)
4
Center Supports
Riveted End Rails
Ceiling bracket (non-motorized install only)
Vertical Upright (3-Hole)
Wire Decking
MyLifters Power Adapters Smart Track & Hardware
Riveted Side Rails
M6 x 15mm Bolt
M6 Flange Nut
M6 Washer
Plastic Plug
Required Tools (not included)
• Drill
• Ratchet with ½” and
10mm Socket
• Stud Finder
• Ladder
• 10mm Wrench
• Rubber Mallet
• Safety Glasses
• Pencil
• Tape Measure
• Screwdriver (flat blade)
5
Platform Installation | Assemble Platform Overhead Storage Rack
Step 1: Assemble Platform Overhead Storage Rack
1. Align the holes on two of the riveted side rails. NOTE: All four side rails are
the same so no need to worry about using the wrong ones.
2. Using the 10mm socket and wrench plus 4 bolts, 4 washers and 4 nuts,
fasten the two riveted side rails together using the outer holes only, as shown.
Place the washer on the bolt before inserting it into the hole on the side rail.
(fig 1.1). NOTE: The center holes will be used to attach the center support
later in the assembly process.
3. Repeat steps 1 and 2 for the remaining side rails. When finished with this
step, you should have two assembled side rails.
fig 1.1
Do not fasten using these holes
at this stage of assembly.
6
Platform Installation | Assemble Platform Overhead Storage Rack
Step 1: Assemble Platform Overhead Storage Rack (cont.)
4. Join a side rail with an end rail using a vertical upright post. We suggest
using a rubber mallet and screwdriver (fig 1.2) to ensure the rivets are
properly seated.
5. Once the rivets are fully seated, insert a plastic plug as shown. (fig 1.3)
6. Repeat steps 4 and 5 for each of the four corners so all side and end rails are
fastened together.
NOTE
NOTE: Opposite ends of the side rails may come loose while hammering other side rails into place.
Be sure to check that all rivets are properly seated once you have attached all side and end rails.
Insert plastic plug to hold vertical
upright and rails in place.
fig 1.2
fig 1.3
7
fig 1.4
fig 1.4
Platform Installation | Assemble Platform Overhead Storage Rack
Step 1: Assemble Platform
Overhead Storage Rack (cont.)
7. Fasten the center support to the
side rails as shown using the
remaining bolts, nuts and washers.
(fig 1.4)
8. Attach the remaining center
supports to the side rails by
inserting the rivets into the keyhole
openings. Make sure the rivets are
fully seated. (fig 1.5)
fig 1.5
fig 1.5
8
Platform Installation | Assemble Platform Overhead Storage Rack
Step 1: Assemble Platform Overhead Storage Rack (cont.)
9. The frame of the platform is now fully assembled (fig 1.6) and ready to add the wire decking.
10. Place the wire decking on the platform frame. The edge of each section of the wire decking (except the outer edges)
should rest on a center support. (fig 1.7)
Edge of wire decking
resting on center supports.
fig 1.6 fig 1.7
9
Platform Installation | Smart Track Installation Overview
Step 2: Install Smart Track
• Lag bolts used to secure Smart Track must be centered in ceiling joists.
• If you are not confident locating and anchoring items to ceiling joists do not
attempt this installation.
• Smart Track is designed to be installed with two lag bolts. Load must only to
be applied between lag screws.
• Smart Track is designed to be secured to flat garage ceilings. DO NOT mount
the Smart Track to walls or angled ceilings. Failure to follow instructions
could result in property damage, serious injury, or death.
• If you have any questions or concerns about the quality of your ceiling
structure discontinue installation and consult a structural engineer.
STOP:
Read Before
Continuing
Table des matières
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
