Skycut C Series Manuel utilisateur
CUT_C MANUAL
SKYCUT
1
Version：CUT_C V2.0
CUT_C MANUAL
SKYCUT
2
Chapter One Safety Precaution
Chapter Two Standard Parts
Chapter Three Installation
3.1 Installation and Connection
3.1.1 Cutting Environment
3.1.2 Connect cutter to PC
3.1.3 USB Driver Installation
3.2 Cutting Media Installation
3.3 Tools Installation
Chapter Four WIFI Setting
Chapter Five Parts Name
Chapter Six General Setting
6.1 Main Menu
6.2 MotorSet
6.3 Camera interface
6.4 Sysset menu
Chapter Seven Function and operation
7.1 Power on
7.2 Power off
7.3 Pressure,speed setting
7.4 Original point setting
7.5 Test cut
7.6 Pause and cancel work.
7.7 Calibrate (one head)
7.8 Calibrate (two heads，D Serial machine)
7.9 Camera threshold value setting.
7.10 Auto contour cut feature.
7.11 Manually contour cut
7.12 X,Y cutting scale setting
7.13 U disk operation
7.14 Language setting
CUT_C MANUAL
SKYCUT
3
7.15 Unit setting
7.16 Screen back ground setting
7.17 LED light setting
7.18 WIFI setting.
7.19 Quick return to main interface
7.20 Offset
Chapter Eight Specification operation
Chapter Nine Warranty
Chapter Ten Trouble shoot
CUT_C MANUAL
SKYCUT
4
Chapter One Safety Precaution
The following icons are used in the manual; aims to make sure the user operate the
cutter properly to avoid damaged the cutter. Please comply with the explanation of
the icon.
1.1 Definition of Warning Symbols：
The symbol ” is prepared to arouse operator's highly
attention when in process.
The symbol “ ” specifies the activities to be forbidden.
The symbol is prepared to arouse operator's highly
attention. The symbols in triangles specify the cases to be
attentive. The symbol in the left warns you of electric shock.
The symbol specifies the activities to be forbidden. The
symbol in the circle specifies the acts to be forbidden. The
symbol in the left tells you no detachment.
1.2 Caution：
Do not leak any liquid or drop
metal into the machine, such
things may result in fire.
Do not touch the knife top
with your finger to prevent
injury or perspiration of knife
head.
Do not damage or random
replace the supplied power
cable. Do not excessively
bend, pull, bundle the power
cable or place weight on it,
otherwise the power source
may be damaged even fire or
electric shock is thus
incurred.
CUT_C MANUAL
SKYCUT
5
1.3 Warning：
Do not use the power source not meeting rating voltage,
otherwise
fire or electric shock may be resulted in.
If the machine gives out smoke or unpleasing smell, or noise
sounds
please do not use it .in such cases, continuing using it may
result in
fire or electric shock.
Do not put out the plug when the power is on to avoid
damage to the
Machine.
Make sure the machine grounded otherwise electric shock
or mechanic default may be resulted in.
If you are not going to use the
machine for a long time,
please unplug the power
cable from the receptacle,
otherwise fire possibly
happens.
When operating the machine,
do not place either of your
hands on capstan to avoid
injury.
Place the machine on a stable
surface, otherwise the machine
may fall therefore get
damaged.
To unplug the power cable
from receptacle, please hold
the plug instead of the cable,
strongly pulling of the cable
possibly results in electric
shock or fire.
Any operation is forbidden in
case of storm or lighting to
prevent damaged of machine.
CUT_C MANUAL
SKYCUT
7
Chapter Three Installation
3.1 Installation and Connection
3.1.1 Cutting Environment
Place the cutter in adequate space in case to replace.
The place for installing the cutter shown as below。
Don’t install your cutter in the following place
- The place where is direct sunlight
- The place where is vibration
- The place where is full dust
- The place where is drought
3.1.2 Connect cutter to PC
Use USB cable connect to PC;
To make the connection between cutter and computer,
you are offered two possibilities: USB interface and U disk
(WIFI is option). For USB connection, you need to install the
driver equipped with the cutter first. (Please refer to 3.1.3) ,WIFI
setting refer to Chapter Four WIFI setting.
VinylCutter
CUT_C MANUAL
SKYCUT
8
3.1.3 USB Driver Installation
When first time use cutter,need to install USB driver.
①Download USB driver from web,find out folder with file
(ftdi_ft232_drive),double click ftdi_ft232_drive.exe,computer will shows
following window
The window will be closed automatically after finish installation.
Notice: If no following information during install
Please wait about 3 mints,and then close it.
②Power on machine,use USB cable to connect machine and computer.
③When first time connect computer,it will take time to load USB driver.
④Check machine COM port.Right Click”This PC”,it will popup following
box,click”Manager”.
CUT_C MANUAL
MANUAL
SKYCUT
9
Then,click “Device Manager”
“USB Serial Port(COM4)”, COM4 is the COM port the machine is using now.
3.2 Cutting Media Installation
Cautions of Media Preservation
- Keep the media away from direct sunlight and water when before and after unpacked.
You should keep the media in dry, shady and cool place after using it.
- Do not put the media in the vertical position, to avoid mess and damage the edge of
the media
- Do not print media in pile.
Cautions of Media Loading
- Avoid the temperature and humidity changes after unpack thebox.
- According to the media feature, when low temperature, media is easy to curl, when
high temperature, it is easy to crease.
- Do not use the media when it is crease, curl or dusty.
- Do not fall or moisturize the media, otherwise it may effects the cutting quality or
result in damaging the cutter.
- Before loading the media, you should roll the media. The cutter
is both suitable for single sheet
3.2.1 Press down the handle of paperweight wheel behind the machine to raise the
paperweight wheel.
CUT_C MANUAL
MANUAL
SKYCUT
10
3.2.2 Insert the media into the space between paperweight wheel and
main shaft, and pull out the media to appropriate length from the front
of the host.
3.2.3 Move the paperweight wheel to the white identified area, then
adjust position of the media.
The cutter adopts high-precision transmission shaft, and pay
attention to the position of the paperweight wheel. The
paperweight wheel must be fixed above the white identified
area on the transmission shaft.
3.2.4 Raise handle of paperweight wheel, to make paperweight wheel
down to press paper.
3.3 Tools Installation
CAUTION
Do not touch the knife top with
your finger
Autres manuels pour C Series
1
Ce manuel convient aux modèles suivants
4
Table des matières
