Sinope TH1124NP Manuel utilisateur

TH1124NP

Installation Guide

Non-Programmable Thermostat

for Electric Heating

Setpoint temperature

Ambient temperature

Heating indicator

Make sure that the

breakers for your heating

system are off at the main

electrical panel.

Use the connectors provided to connect the thermostat

wires to the wires in the electrical box.

Note: The wires of this thermostat are non-polarized.

Replace the cover

and lock

Power up the

thermostat.

Unlock and lift the

thermostat cover.

INSTALL YOUR THERMOSTAT

123

YOUR TH1124NP THERMOSTAT

The installation of this thermostat must be

performed by a certified electrician and comply

with the national and local electrical codes and

regulations.

A loose connection can be a fire hazard. Special CO/ALR

solderless connectors must be used when connecting

with aluminum conductors.

Warnings

Four-wire installation

Two-wire installation

* Improperly installed electrical wires could burn the wire connectors.

Make sure to firmly tighten the wire connectors for a

secure connection. A loose connection can be a fire

hazard.

To install wire connectors, you must:

Insert the two wires into the wire nut so that their

copper ends are parallel.

Turn the wire connector clockwise until there is strong tension.

Pull on the threads to make sure they are secure, leaving no

gaps between them. * If the threads seem to come loose,

repeat the process.

3/4"

TH1124NP

Installation Guide

Non-Programmable Thermostat

for Electric Heating

Setpoint temperature

Ambient temperature

Heating indicator

Make sure that the

breakers for your heating

system are off at the main

electrical panel.

Use the connectors provided to connect the thermostat

wires to the wires in the electrical box.

Note: The wires of this thermostat are non-polarized.

Replace the cover

and lock

Power up the

thermostat.

Unlock and lift the

thermostat cover.

INSTALL YOUR THERMOSTAT

123

YOUR TH1124NP THERMOSTAT

The installation of this thermostat must be

performed by a certified electrician and comply

with the national and local electrical codes and

regulations.

A loose connection can be a fire hazard. Special CO/ALR

solderless connectors must be used when connecting

with aluminum conductors.

Warnings

Four-wire installation

Two-wire installation

* Improperly installed electrical wires could burn the wire connectors.

Make sure to firmly tighten the wire connectors for a

secure connection. A loose connection can be a fire

hazard.

To install wire connectors, you must:

Insert the two wires into the wire nut so that their

copper ends are parallel.

Turn the wire connector clockwise until there is strong tension.

Pull on the threads to make sure they are secure, leaving no

gaps between them. * If the threads seem to come loose,

repeat the process.

3/4"

TH1124NP

Installation Guide

Non-Programmable Thermostat

for Electric Heating

Setpoint temperature

Ambient temperature

Heating indicator

Make sure that the

breakers for your heating

system are off at the main

electrical panel.

Use the connectors provided to connect the thermostat

wires to the wires in the electrical box.

Note: The wires of this thermostat are non-polarized.

Replace the cover

and lock

Power up the

thermostat.

Unlock and lift the

thermostat cover.

INSTALL YOUR THERMOSTAT

123

YOUR TH1124NP THERMOSTAT

The installation of this thermostat must be

performed by a certified electrician and comply

with the national and local electrical codes and

regulations.

A loose connection can be a fire hazard. Special CO/ALR

solderless connectors must be used when connecting

with aluminum conductors.

Warnings

Four-wire installation

Two-wire installation

* Improperly installed electrical wires could burn the wire connectors.

Make sure to firmly tighten the wire connectors for a

secure connection. A loose connection can be a fire

hazard.

To install wire connectors, you must:

Insert the two wires into the wire nut so that their

copper ends are parallel.

Turn the wire connector clockwise until there is strong tension.

Pull on the threads to make sure they are secure, leaving no

gaps between them. * If the threads seem to come loose,

repeat the process.

3/4"

TH1124NP

Installation Guide

Non-Programmable Thermostat

for Electric Heating

Setpoint temperature

Ambient temperature

Heating indicator

Make sure that the

breakers for your heating

system are off at the main

electrical panel.

Use the connectors provided to connect the thermostat

wires to the wires in the electrical box.

Note: The wires of this thermostat are non-polarized.

Replace the cover

and lock

Power up the

thermostat.

Unlock and lift the

thermostat cover.

INSTALL YOUR THERMOSTAT

123

YOUR TH1124NP THERMOSTAT

The installation of this thermostat must be

performed by a certified electrician and comply

with the national and local electrical codes and

regulations.

A loose connection can be a fire hazard. Special CO/ALR

solderless connectors must be used when connecting

with aluminum conductors.

Warnings

Four-wire installation

Two-wire installation

* Improperly installed electrical wires could burn the wire connectors.

Make sure to firmly tighten the wire connectors for a

secure connection. A loose connection can be a fire

hazard.

To install wire connectors, you must:

Insert the two wires into the wire nut so that their

copper ends are parallel.

Turn the wire connector clockwise until there is strong tension.

Pull on the threads to make sure they are secure, leaving no

gaps between them. * If the threads seem to come loose,

repeat the process.

3/4"

TH1124NP

Installation Guide

Non-Programmable Thermostat

for Electric Heating

Setpoint temperature

Ambient temperature

Heating indicator

Make sure that the

breakers for your heating

system are off at the main

electrical panel.

Use the connectors provided to connect the thermostat

wires to the wires in the electrical box.

Note: The wires of this thermostat are non-polarized.

Replace the cover

and lock

Power up the

thermostat.

Unlock and lift the

thermostat cover.

INSTALL YOUR THERMOSTAT

123

YOUR TH1124NP THERMOSTAT

The installation of this thermostat must be

performed by a certified electrician and comply

with the national and local electrical codes and

regulations.

A loose connection can be a fire hazard. Special CO/ALR

solderless connectors must be used when connecting

with aluminum conductors.

Warnings

Four-wire installation

Two-wire installation

* Improperly installed electrical wires could burn the wire connectors.

Make sure to firmly tighten the wire connectors for a

secure connection. A loose connection can be a fire

hazard.

To install wire connectors, you must:

Insert the two wires into the wire nut so that their

copper ends are parallel.

Turn the wire connector clockwise until there is strong tension.

Pull on the threads to make sure they are secure, leaving no

gaps between them. * If the threads seem to come loose,

repeat the process.

3/4"

TH1124NP

Installation Guide

Non-Programmable Thermostat

for Electric Heating

Setpoint temperature

Ambient temperature

Heating indicator

Make sure that the

breakers for your heating

system are off at the main

electrical panel.

Use the connectors provided to connect the thermostat

wires to the wires in the electrical box.

Note: The wires of this thermostat are non-polarized.

Replace the cover

and lock

Power up the

thermostat.

Unlock and lift the

thermostat cover.

INSTALL YOUR THERMOSTAT

123

YOUR TH1124NP THERMOSTAT

The installation of this thermostat must be

performed by a certified electrician and comply

with the national and local electrical codes and

regulations.

A loose connection can be a fire hazard. Special CO/ALR

solderless connectors must be used when connecting

with aluminum conductors.

Warnings

Four-wire installation

Two-wire installation

* Improperly installed electrical wires could burn the wire connectors.

Make sure to firmly tighten the wire connectors for a

secure connection. A loose connection can be a fire

hazard.

To install wire connectors, you must:

Insert the two wires into the wire nut so that their

copper ends are parallel.

Turn the wire connector clockwise until there is strong tension.

Pull on the threads to make sure they are secure, leaving no

gaps between them. * If the threads seem to come loose,

repeat the process.

3/4"

Operatlng voltage: 120 / 208 / 240 Vac, 60 Hz

Maximum load:

16.7 A / 4000 w @ 240 Vac

Resistive load only.

Minimum load:

1.25 A / 300 W @ 240 Vac

Setpoint range: 41 ˚F to 86 ˚F (5 ˚C to 30 ˚C)

Display range: 32 ˚F to 99 ˚F (0 ˚C to 50 ˚C)

Resolution: ±1 ˚F (±0.5 ˚C)

Storage: -4 ˚F to 122 ˚F (-20 ˚C to 50 ˚C)

Operation: 32 ˚F to 122 ˚F (0 ˚C to 50 ˚C)

Compatible with an electric heating system such as:

• Baseboard heater [short cycle]

• Convector [short cycle]

• Fan-forced convector [long cycle)

• Radiant ceiling heating

OFF MODE TECHNICAL SPECIFICATIONS

3-year limited warranty

SINOPÉ TECHNOLOGIES INC. warrants the components of their products against

defects in material and workmanship for a 3 year period from the date of purchase,

under normal use and service, when proof of purchase of such is provided to the

manufacturer. This warranty does not cover any transportation costs that may be

incurred by the consumer. Nor does it cover a product that has been improperly

installed, misused or accidentally damaged. The obligation of Sinopé Technologies

Inc., under the terms of this warranty, will be to supply a new unit and this releases

the manufacturer from paying the installation costs or other secondary charges

linked to replacing the unit or the components.

For more information, visit our Website:

660-1511-0000-C

ADVANCED SETTINGS

Control cycle

SHT (short cycle for electric baseboard)

FAN (long cycle for fan forced heater)

(Default: SHT)

Cycle length

Setpoint Min

Scale

Temperature scale

°C or °F (Default: °F)

Minimum setpoint

41 °F to 86 °F – (Default: 41 °F)

To change the thermostat’s settings, you need to:

Get the setpoint to its minimum and hold the button for

10 seconds to access the menu.

Press the or button to change the setting.

Press the and buttons simultaneously to save and go to

the next parameter. Continue to press until the end of the list

to exit the menu.

Name Parameters & settings Display

Setpoint Max

Maximum setpoint

41 °F to 86 °F – (Default: 86°F)

Backlight

Backlight control

ON, OFF or BED – (Default: ON)

ON (backlight always active, will dim

according to ambient light)

OFF (will only turn on when a button

is pressed)

BED (bedroom mode - backlight will dim

according to ambient light and will turn

OFF below 20% of luminosity)

Hold for 10 sec.

To put the thermostat in OFF mode, hold the buttons and

for 10 seconds.

To exit the OFF mode, hold the buttons and for

10 seconds or raise/lower the setpoint.

Hold for 10 sec.