Simrad BSM-3 Manuel utilisateur

ENGLISH

BSM-3

Installation Manual

simrad-yachting.com

| 3

| BSM-3 Installation Manual

Preface

Disclaimer

As Navico is continuously improving this product, we retain the

right to make changes to the product at any time which may not be

reﬂected in this version of the manual. Please contact your nearest

distributor if you require any further assistance.

It is the owner’s sole responsibility to install and use the instrument

and transducers in a manner that will not cause accidents, personal

injury or property damage. The user of this product is solely

responsible for observing safe boating practices.

NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND

AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT

IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY

VIOLATE THE LAW.

Governing Language: This statement, any instruction manuals,

user guides and other information relating to the product

(Documentation) may be translated to, or has been translated from,

another language (Translation). In the event of any conﬂict between

any Translation of the Documentation, the English language

version of the Documentation will be the oﬃcial version of the

Documentation.

This manual represents the product as at the time of printing.

Navico Holding AS and its subsidiaries, branches and aﬃliates

reserve the right to make changes to speciﬁcations without notice.

Trademarks

NMEA 2000 is a registered trademark of the National Marine

Electronics Association.

Navionics is a registered trademark of Navionics SpA.

Simrad is a trademark of Kongsberg Maritime AS Company

registered in the US and other countries and is being used under

license.

B&G, Lowrance, StructureScan, Navico, SonicHub, SimNet, Skimmer,

InsightHD, Broadband Radar, Broadband Sonar, and SonarHub are

trademarks of Navico, registered in the US and other countries.

4 | | BSM-3 Installation Manual

Warranty

The warranty card is supplied as a separate document.

In case of any queries, refer to the brand web site of your display or

system: www.simrad-yachting.com

Declarations and conformance

This equipment is intended for use in international waters as well as

coastal sea areas administered by countries of the E.U. and E.E.A.

Compliance Statements

BSM-3:

• Comply with CE under EMC directive 2004/108/EC

• Comply with the requirements of level 2 devices of the

Radiocommunications (Electromagnetic Compatibility)

standard 2008.tra es

The relevant Declaration of Conformity is available in the following

website, under the model documentation section:

www.simrad-yachting.com

Warning

The user is cautioned that any changes or modiﬁcations not

expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that the interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment oﬀ and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit diﬀerent from

that of the receiver

• Consult the dealer or an experienced technician for help.

| 5

| BSM-3 Installation Manual

About this manual

This document describes how to install the BSM-3 and connect the

unit to transducers and display units.

Separate installation instruction for transducers are included with

the transducer package.

The BSM-3 is compatible with the following MFD displays and

systems:

• NSE

• NSO, NSO evo2

• NSS, NSS evo2

http://support.simrad-yachting.com

¼Note: Make sure the MFD has up-to-date software, - refer to the

website: www.simrad-yachting.com

Important text that requires special attention from the reader is

emphasized as follows:

¼Note: Used to draw the reader’s attention to a comment or some

important information.

Warning: Used when it is necessary to warn personnel that they should

proceed carefully to prevent risk of injury and/or damage to equipment/per-

sonnel.

6 | Contents | BSM-3 Installation Manual

Contents

7 Introduction

7 BSM-3 module layout

7 Parts included in package

9 Installation and wiring

9 Mounting location

10 Securing BSM-3 module

11 Wiring

12 Connecting the BSM-3 to your display

13 Transducer connection

13 BSM-3 connectors

14 Transducer with a 7-pin connector

14 Transducer with bare wires

15 Airmar transducers

18 Trouble shooting

19 Technical specication

21 Dimensional drawings

22 Spare parts and accessories

22 Spare parts

22 Accessories

22 Transducers

| 7

Introduction | BSM-3 Installation Manual

Introduction

BSM-3 module layout

removable

cover

led status

indicators

ethernet

connector

connectors

Parts included in package

For spare parts and part numbers, see“Spare parts and accessories”

on page 22.

Item No. Description

1 BSM-3 sounder module

1 Ethernet cable, 1.8 m (6 ft)

1Power cable (bare wires), 2 m (6.5 ft)

Cable glands for bare wire transducer

installation

GroundinG

screW

8 | Introduction | BSM-3 Installation Manual

Item No. Description

4 Screws

1Spare Fuse kit including;

3A Fuses and fuse holders

1 Warranty card

1 This manual

Required tools and supplies

Drill

2 mm

(5/64”)

Drill Bit Screw driver Pencil

| 9

Installation and wiring | BSM-3 Installation Manual

Installation and wiring

Mounting location

Before installing the BSM-3, consider location and cable runs

necessary to connect the module to display unit, transducer and

power source.

The mounting location must allow for required working area when

connecting the cables. Also ensure that the location allows viewing

the unit’s LED indicators.

The units should be mounted with special regard to the units’

environmental protection, temperature range and cable length.

The mounting surface needs to be structurally strong, with as little

vibration as possible. If possible, mount the unit close to the edges

of a panel to minimize vibration.

Do not run the transducer cabling near the BSM-3 power cables,

any VHF antenna coax cables or any DC or AC power cables. Avoid

placing Ethernet cables close to VHF antennas.

The BSM-3 conforms to the appropriate Electromagnetic

Compatibility (EMC) standards, but proper installation is required

to get best use and performance from this product. Ensure you

have as much separation as possible between diﬀerent electrical

equipment, (see diagram below).

Electromagnetic interference

Gasoline fumes

Vibration

Heat

Sunlight

Salt spray

Physical damage

2.0 m (6.5 ft) Min 1.8 m (6 ft) Min

1.5 m (5 ft) Min

RADAR

Radio or AIS Transmitter

Compass

10 | Installation and wiring | BSM-3 Installation Manual

Securing BSM-3 module

Mount the BSM-3 on a vertical surface with the power and

transducer cable connections exiting downwards.

Fasten the BSM-3 by using the 4 stainless steel self tapping screws

included with the unit.

Table des matières

Autres manuels Simrad Équipement marin

Simrad

Simrad ED162 Manuel utilisateur

Simrad

Simrad BoatConnect Manuel utilisateur

Simrad

Simrad AI80 Manuel utilisateur

Simrad

Simrad RF40 Manuel utilisateur

Simrad

Simrad BSM-2 Manuel utilisateur

Simrad

Simrad EY500 Manuel utilisateur

Simrad

Simrad RF25 Manuel utilisateur

Simrad

Simrad GC80 EXPANDED Manuel utilisateur

Simrad

Simrad EK80 Manuel utilisateur

Simrad

Simrad IS40 Manuel utilisateur

Simrad

Simrad ES70 - DOWNLOAD AND INSTALLATION REV B Manuel utilisateur

Simrad

Simrad DD15 Manuel utilisateur

Simrad

Simrad SX90 - DATASHEET FOR NAVAL AND COAST GUARD REV... Manuel utilisateur

Simrad

Simrad GO XSE Series Manuel utilisateur

Simrad

Simrad ES60 - DATASHEET REV A Manuel utilisateur

Simrad

Simrad Maris ECDIS900 Manuel utilisateur

Simrad

Simrad FS70 - REV 3 Manuel utilisateur

Simrad

Simrad ME70 - REV C Manuel utilisateur

Simrad

Simrad ER60 - REV B Manuel utilisateur

Simrad

Simrad ITI TWIN RIG - QUICK REFERENCE GUIDE REV A Manuel utilisateur

Simrad

Simrad MS70 Manuel utilisateur

Simrad

Simrad Maris ECDIS900 Manuel utilisateur

Simrad

Simrad SN90 Manuel utilisateur

Simrad

Simrad IS42J Manuel utilisateur

Manuels Équipement marin populaires d'autres marques

Clarion

Clarion CMS2 Manuel de réparation

EBS

EBS M7000 Manuel utilisateur

Kongsberg

Kongsberg M3 Bathy Manuel utilisateur

NPK

NPK SCS-1002 Manuel utilisateur

Furuno

Furuno FE-800 Manuel utilisateur

Harken

Harken 1561 Manuel utilisateur

Notifier

Notifier FS-BSO Manuel utilisateur

Raymarine

Raymarine ST40 Manuel utilisateur

E2S

E2S E2XS112UL Manuel utilisateur

R2Sonic

R2Sonic 2026 Manuel utilisateur

COBHAM

COBHAM SAILOR 6000 Manuel utilisateur

Clarion

Clarion GR10BT Manuel de réparation

Raymarine

Raymarine Maxiview ST80 Guide de l'utilisateur

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Instructions de montage

Raymarine

Raymarine ST60 Tridata Guide de l'utilisateur

olympia electronics

olympia electronics ΒS-531/1/MAR Manuel utilisateur

Sonic

Sonic 2024 Manuel utilisateur

Quicksilver

Quicksilver 88688A25 Manuel