SimpliFire SF-CHAF-36 Manuel utilisateur

1SimpliFire • Inception Decorative Front Instructions (Chateau Forge, Halston) • 4200-930 • Rev B • 8/23

Leave this manual with party responsible for use

and operation.

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during instal-

lation. Sheet metal edges are sharp.

CAUTION! Do not install damaged components.

Figure 1 Decorative Front Styles

Note: To avoid potential damage to hearth pad or flooring,

protect area in front of fireplace by laying cardboard or

blanket down.

Inception Decorative Front

Model: SF-CHAF-36, SF-HAL-36

- Installation Instructions -

For Models: SF-INC36

HALSTON

CHATEAU

FORGE

SHIPPING BRACKET

(DISCARD)

MOUNTING SCREWS x 4 (10-24 X 3/4”)

(A)

SEPARATE AT

THESE POINTS

(BEFORE SEPARATION)

MOUNTING BRACKETS

(AFTER SEPARATION)

(B) (C)

MOUNTING BRACKETS

Figure 2 Components Overview

Figure 3 Side Panels Overview

LEFT AND RIGHT SIDE PANELS

NOTE: Side panels located in appliance

component box.

(D) (E)

2SimpliFire • Inception Decorative Front Instructions (Chateau Forge, Halston) • 4200-930 • Rev B • 8/23

A. Finishing Material

Table 1. Decorative Front Dimensions

These decorative fronts are designed to be installed as

“Overlap” or “Inside Fit”. Refer to Table 1.

Overlap Method: Finishing material that is 1” or less

(such as marble or tile) is installed up to the replace

opening on the sides and top. The mounting brackets are

adjusted “out” so that the edges of the mounting brackets

are ush with the face of the nishing material. The back

of the decorative front contacts the face of the nish mate-

rial, thus the decorative front “overlaps” the nish materi-

al. Refer to the appliance installation instructions for more

detailed information. Reference Figure 4 for combustible

clearances required for 240VAC Supplied Appliances with

Overlap Fit Front Installations.

Inside Fit Method: Typically, the inside t method is

only used when nish material greater than 1” is preferred

(such as cultured stone). This nish material is installed

adjacent to the decorative front sides and top.

The mounting brackets are to be installed “ush” with the

black edges of the inside surround opening. Do not install

nish material greater than one inch thick up to the view-

ing area on top , bottom or sides.

When installed, the back of the decorative front contacts

the black surround on the replace, thus the decorative

front is “inside” the adjacent nish material on the top and

sides. Refer to the appliance installation manual for more

detailed information.

DECORATIVE

FRONT HEIGHT WIDTH

HAL-36 32-7/8 IN. 37-1/4 IN.

CHAF-36 32-7/8 IN. 37 IN.

INTRODUCTION

These are instructions for the Chateau Forge and Halston

decorative fronts. These decorative fronts are compatible

with the Inception appliance.

NOTE: The hammered pattern, decorative wire placement

and other features of the Chateau Forge decorative front

may vary from the showroom display model due to the hand-

crafted nature of the Chateau Forge decorative front.

Tools Needed:

• 1/4” Nut Driver 32-7/8 IN. MIN.

(835 mm)

Figure 4

When using 240VAC input, all overlapped

nishing material, behind the decorative front,

in the shaded area, must be a non-combustible

material only.

3SimpliFire • Inception Decorative Front Instructions (Chateau Forge, Halston) • 4200-930 • Rev B • 8/23

2. Remove mounting bracket assembly and bend the

mounting bracket assembly vertically to separate the

left and right brackets (B and C). See Figure 3.

Do not bend mounting bracket tabs.

Discard screws and shipping brackets. See Figure 3.

B. Installation

1. Remove components from package. Components in-

cluded will depend on the decorative front being installed.

The mounting brackets are secured to a shipping bracket

located on the back side of the decorative front. Remove

shipping bracket using 1/4 in. nut driver and remove

mounting brackets from packaging.

MOUNTING

BRACKETS

MOUNTING

SCREWS (A)

(B & C)

SIDE PANELS

(D & E)

Figure 5 Attach Side Panels

3. Remove side panels (D and E) from appliance compo-

nent box. See Figure 3.

4. Attach mounting brackets (B and C) and side panels

(D and E) to appliance using the four mounting screws

(A). See Figure 5. Locate the laser-cut number 36 on

the bracket which represents the size of the decora-

tive front. This marking also indicates the top of the

bracket. Install the bracket so that the front edge of the

bracket sits ush with the desired depth of the decora-

tive front. Mounting tabs should extend at least 1/8

inch past desired depth. See Figure 6. Side panels

install over the mounting brackets using the same

mounting screws (A).

For example: If the decorative front is to t tight

against the appliance (Inside Fit), install the brackets

ush with the face of the appliance. If the decora-

tive front is to t up tight against a nishing material

with maximum thickness of one inch (Overlap Fit), the

brackets should be ush with the face of the mate-

rial. For both inside t and overlap t applications, the

mounting tabs should extend at least 1/8 inch past

desired depth. Refer to Section A, “Finishing Material”

for more information.

CONNECT

WIRE

HARNESS

5. Connect the wire harness at the lower right of the front

to the corresponding connector from the appliance,

See Figure 5.

6. Install the decorative front to the mounting brackets

by engaging the brackets mounted on the decorative

front assembly to the mounting brackets located on

the appliance. See Figure 7. Ensure the decorative

front is properly attached and securely positioned on

the appliance.

NOTE: Before installing decorative front, make sure the

appliance junction box master switch is ipped to the

ON position.

Figure 6 Install Decorative Front

Figure 7 Install Decorative Front

MOUNTING TABS (4)MOUNTING TABS (4)

SLOTTEDSLOTTED

BRACKETS (4)BRACKETS (4)

4SimpliFire • Inception Decorative Front Instructions (Chateau Forge, Halston) • 4200-930 • Rev B • 8/23

C. Cleaning Instructions for Decorative

Fronts

Use a microber cloth and Windex® Original Glass

Cleaner or 03M003 Stove Bright® Glass Cleaner to

clean the decorative front immediately after installation

to remove acids deposited by the installer or technician.

Spray the cleaner onto the microber cloth and carefully

wipe the entire surface. The decorative front should

be cleaned in this manner annually by the homeowner

to remove ngerprints or other contaminants. Once

oxidation of the paint pigment has occurred, cleaning will

not restore the original color.

D. Replacement Parts

• Side Panels SRV4200-106

• Mounting Brackets SRV2353-216

• Vanity Panel Assembly SRV4200-034

• Door Buttons Jumper SRV4200-183

SimpliFire, a brand of Hearth & Home Technologies

7571 215th Street West, Lakeville, MN 55044

www.hearthnhome.com

Please contact your SimpliFire dealer

for the location of your nearest SimpliFire dealer,

please visit www.hearthnhome.com.

Ce manuel convient aux modèles suivants

Autres manuels SimpliFire Accessoires de cheminée

SimpliFire

SimpliFire SF-SC43-BK Manuel utilisateur

SimpliFire

SimpliFire SF-SC43-BK Manuel utilisateur

SimpliFire

SimpliFire FOL-INC36 Manuel utilisateur

SimpliFire

SimpliFire HERITAGE-26-CH Manuel utilisateur

SimpliFire

SimpliFire GI-32-ZC Manuel utilisateur

SimpliFire

SimpliFire SF-OD43 Manuel utilisateur

SimpliFire

SimpliFire SF-INS30-BK Manuel utilisateur

SimpliFire

SimpliFire SF-FORMAT36 Manuel utilisateur

SimpliFire

SimpliFire SF-WM36 Manuel utilisateur

SimpliFire

SimpliFire SF-FORMAT36 Manuel utilisateur

SimpliFire

SimpliFire SF-SCT43-BK Manuel utilisateur

SimpliFire

SimpliFire SF-OD43 Manuel utilisateur

SimpliFire

SimpliFire CRESTWOODC23-OK Manuel utilisateur

SimpliFire

SimpliFire SF-ALLP50-BK Manuel utilisateur

SimpliFire

SimpliFire SF-FORMAT36 Manuel utilisateur

SimpliFire

SimpliFire SF-BI30-EB Manuel utilisateur

SimpliFire

SimpliFire Wescott Mantel Kit Manuel utilisateur

SimpliFire

SimpliFire SF-ALL40-BK Manuel utilisateur

Manuels Accessoires de cheminée populaires d'autres marques

Valor

Valor L2 1700K Manuel utilisateur

Exodraft

Exodraft Xzense Manuel utilisateur

Whalen

Whalen Ruso MNFP62BF23-6 Manuel utilisateur

Lopi

Lopi Hearthview 864 Manuel utilisateur

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuel utilisateur

EdilKamin

EdilKamin SERBATOIO 250 Guide de démarrage rapide

Bronpi

Bronpi KIT-1 Manuel utilisateur

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuel utilisateur

Travis Industries

Travis Industries 33 DVI Manuel utilisateur

Superior

Superior ASD3628-TI Manuel utilisateur

pleasant hearth

pleasant hearth OFP28WG Manuel utilisateur

IHP

IHP Astria Series Manuel utilisateur

Firegear

Firegear FG-H-2110SS Manuel utilisateur

Nibe

Nibe Contura C i31 Manuel utilisateur

kozy heat

kozy heat KZK-052 Manuel utilisateur

Bluegrass Living

Bluegrass Living BC18NR Guide de démarrage rapide

pleasant hearth

pleasant hearth IRIS SCROLL Manuel utilisateur

Cooke

Cooke Glass Wind Guard Manuel utilisateur