Simex SRD-99X Manuel utilisateur

Assisting the automation
industry since 1986   
User manual
DATA RECORDER
SRD-99 
•Firmware: v.3.40 (b1) or higher
•Loggy Soft: v.1.10.0 or higher
•S-Toolkit: v.2.1.0 or higher
Read the user's manual carefully before starting to use the unit or software. 
Producer reserves the right to implement changes without prior notice.
 2019.0 .16 SRD-99X_INSSXEN_v.1.06.001 

User manual - DATA RECORDER SRD-99X and cooperating software
CONTENTS
I. USER MANUAL FOR DATA RECORDER................................................................4
BASIC REQUIREMENTS AND USER SAFETY........................................................................................4
GENERAL CHARACTERISTICS................................................................................................................5
TECHNICAL DATA......................................................................................................................................7
DEVICE INSTALLATION..........................................................................................................................12
1. UNPACKING....................................................................................................................................12
2. ASSEMBLY......................................................................................................................................13
3. CONNECTION METHOD.................................................................................................................15
3.1.Connection  of current type input  ( U/I ver ion )...................................................................19
3.2.Connection  of temperature type input   ( mV/RTD /TC ver ion )..........................................21
4. MAINTENANCE................................................................................................................................22
FRONT PANEL DESCRIPTION................................................................................................................23
PRINCIPLE OF OPERATION...................................................................................................................24
1. MEASUREMENT MODE..................................................................................................................24
1.1.Mea urement range  definition of current input  ( U/I ver ion ).............................................24
1.2.Mea urement range  definition of RTD and TC input  ( mV/RTD/TC ver ion ).....................25
1.3.Recording momentary and averaged data...............................................................................26
2. MODES OF RESULT PRESENTATION..........................................................................................28
2.1. "Single channel" mode............................................................................................................29
2.2."Mea urement  li t" mode.......................................................................................................30
2.3.”Graph” mode...........................................................................................................................32
2.4.”Channel  Li t” mode...............................................................................................................35
3. PRINCIPLE OF OUTPUTS OPERATION........................................................................................37
3.1.Alarm ......................................................................................................................................37
3.2.Output  control.........................................................................................................................38
3.3.Example of output control........................................................................................................40
DEVICE PROGRAMMING.........................................................................................................................41
1. PARAMETERS EDITION.................................................................................................................43
1.1.Numeric and  witching parameter  ("LIST" - type)..................................................................43
1.2. Text parameter ......................................................................................................................44
1.3.“SLIDER” - type parameter .....................................................................................................45
2. DESCRIPTION OF RESULTS PRESENTATION MODES MENU.................................................46
2.1."Mea urement  li t option " menu...........................................................................................46
2.2.”Graph option ” menu..............................................................................................................47
2.3.”Channel  li t option ” menu....................................................................................................47
3. RESULTS PRESENTATION MODES MENU STRUCTURE..........................................................48
4. MAIN MENU DESCRIPTION...........................................................................................................49
4.1.”Device information” menu.......................................................................................................49
4.2.”Di play option ” menu............................................................................................................49
4.3.”Logging  etup” menu..............................................................................................................50
4.4.”Input  etting ” menu (common parameter )...........................................................................53
4.5.”Input  etting ” menu ( U/I ver ion )........................................................................................54
4.6.”Input  etting ” menu ( mV/RTD/TC ver ion ).........................................................................56
4.7.”Output   etting ” menu...........................................................................................................58
4.8.”Date & time  etting ” menu....................................................................................................59
4.9.”RS485 port  etting ” menu.....................................................................................................59
4.10.”Acce   etup” menu.............................................................................................................61
4.11.”USB option ” menu...............................................................................................................61
4.12.”Language” menu...................................................................................................................62
4.13.”Default  etting ” menu..........................................................................................................62
5. MAIN MENU STRUCTURE..............................................................................................................63
DO NLOADING DATA FROM DATA LOGGER.....................................................................................65
1. MODBUS (RS485) DATA DOWNLOAD..........................................................................................65
2

User manual - DATA RECORDER SRD-99X and cooperating software
2. USB PC DATA DOWNLOAD...........................................................................................................65
3. USB FLASH DRIVE (PENDRIVE) DATA DOWNLOAD..................................................................65
THE MODBUS PROTOCOL HANDLING.................................................................................................68
1. LIST OF REGISTERS......................................................................................................................68
2. TRANSMISSION ERRORS HANDLING..........................................................................................73
3. EXAMPLES OF QUERY/ANSWER FRAMES.................................................................................74
USER'S SETTINGS LIST........................................................................................................................77
II. USER MANUAL FOR “LOGGY SOFT”.................................................................84
GENERAL CHARACTERISTICS..............................................................................................................84
INSTALLATION AND STARTUP..............................................................................................................84
USING THE PROGRAM............................................................................................................................87
1. „CURRENT MEASUREMENT” MENU.............................................................................................88
2. „REPORTS” MENU..........................................................................................................................88
2.1.„Table” tab................................................................................................................................89
2.2.„Graph” tab...............................................................................................................................91
3. „CONFIGURATION” MENU.............................................................................................................96
3.1.„Device ” tab............................................................................................................................97
3.2.„Group ” tab - group operation .............................................................................................101
3.3.„Setting ” tab..........................................................................................................................103
4. LIST OF ERRORS AND FAULT DIAGNOSTICS .........................................................................105
III. USER MANUAL FOR “S-TOOLKIT”..................................................................106
GENERAL CHARACTERISTICS............................................................................................................106
INSTALLATION AND STARTUP............................................................................................................106
USING PROGRAM..................................................................................................................................107
1. “INPUTS SETTINGS” TAB.............................................................................................................108
2. “OUTPUTS SETTINGS” TAB.........................................................................................................109
3. “LOGGING SETUP” TAB...............................................................................................................109
4.  “INTERFACE OPTIONS” TAB......................................................................................................110
5. “DEVICE INFORMATION” TAB.....................................................................................................112
6. CONFIGURATION MODES...........................................................................................................113
6.1.Individual configuration of channel .......................................................................................113
6.2.Configuring  elected channel ...............................................................................................113
6.3.Configuring all channel .........................................................................................................113
7. UPDATING DEVICE FIRMWARE..................................................................................................114
 

User manual - DATA RECORDER SRD-99X and cooperating software

Explanation of symbols used in the manual:

- Thi ymbol denote e pecially important guideline concerning the in tallation and

operation of the device. Not complying with the guideline denoted by thi ymbol

may cau e an accident, damage or equipment de truction.

IF THE DEVICE IS NOT USED ACCORDING TO THE MANUAL THE USER IS

RESPONSIBLE FOR POSSIBLE DAMAGES.

- Thi ymbol denote e pecially important characteri tic of the unit.

Read any information regarding thi ymbol carefully

I. USER MANUAL FOR DATA RECORDER

1. BASIC REQUIREMENTS AND USER SAFETY

- The ma ufacturer is ot respo sible for a y damages caused by

i appropriate i stallatio , ot mai tai i g the proper e viro me tal

co ditio s a d usi g the u it co trary to its assig me t.

- Installation should be conducted by qualified personnel . During installation all

available safety requirements should be considered. The fitter is responsible for

executing the installation according to this manual, local safety and EMC

regulations.

- The unit must be properly set-up, according to the application. Incorrect

configuration can cause defective operation, which can lead to unit damage or

an accident.

- If the device is equipped with PE conntector, it should be connected to PE wire.

- If i the case of a u it malfu ctio there is a risk of a serious threat to the

safety of people or property additio al, i depe de t systems a d

solutio s to preve t such a threat must be used.

- The u it uses da gerous voltage that ca cause a lethal accide t. The u it

must be switched off a d disco ected from the power supply prior to

starti g i stallatio of troubleshooti g (i the case of malfu ctio ).

- Neighbouring and connected equipment must meet the appropriate standards

and regulations concerning safety and be equipped with adequate overvoltage

and interference filters.

- Do ot attempt to disassemble, repair or modify the u it yourself. The u it

has o user serviceable parts. Defective u its must be disco ected a d

submitted for repairs at a authorized service ce tre.

User manual - DATA RECORDER SRD-99X and cooperating software

2. GENERAL CHARACTERISTICS

• Multifunctional

Device is designed for recording, displaying current or averaged values and

presentation of technological parameter trends in graphic form.

• Large data storage capacity

The registered measurement results are recorded in the unit's memory. The

capacity of installed memory allows to store over 3 000 000 measurements (8 MB).

• Configurable measurement and control input

The unit has up to 8 channels (depending on version) of measurement signals and

one digital voltage input with programmable functions, e.g. control of the recording

process. Each signal can be freely configured and described. Depending on device

version all measured parameters must be available as current signals (0-20 mA or

-20 mA standards for U/I versio ), voltage signals (0-5 V, 1-5 V, 0-10 V. 2-10 V

standards for U/I versio ), K, S, J, T, N, R, B, E standards for mV/RTD/TC versio

and 60 mV, 75 mV, 100 mV, 150 mV standards for mV/RTD/TC versio ) or

resistance (Pt100, Pt500 or Pt1000 standards for mV/RTD/TC versio ). The

internal analogue-digital converter has a 12 or 16 bit resolution (depending on input

type), which provides high measurement resolution results. Additionally, individual

alphanumeric description (text) of each of the recorded channels is possible.

• Fast serial interface

The data logger is fitted with a galvanic isolation RS- 85 interface, programmed

with ModBus RTU transmission protocol. This enables the connection of a number

of data recorders into the network, remote collecting of data from each unit and also

remote configuration. The application of the RS- 85 interface instead of RS-232 is

due to the possibility of achieving high transmission speeds using transmission lines

of larger length than is possible with the RS-232 interface.

• Built-in USB Host interface (optional)

Optionally the device can be equipped with built-in USB Host interface, allowing for

data transfer to popular USB Flash Drives (PenDrives). This method allows for

significant simplification of unit application: it is no longer necessary to connect PC

and data logger via RS- 85 interface.

Significant acceleration of data transfer is an additional advantage: data download

can be 10 times faster than using RS- 85 interface.

WARNING! Device should work properly with any standard Flash Drives, but

manufacturer can not guarantee proper cooperation with non-standard devices, or

with devices developed after data logger release.

User manual - DATA RECORDER SRD-99X and cooperating software

• ide range of power supply voltage and external sensor power supply

The built-in pulse power supply allows to power the device with 85...230...260 V

AC/DC, 16...24...35 V AC, 19...24...50 V DC, 11...12...16 V DC, 10...12...13 V AC

(depending on version). Data recorder (version with current inputs only) is equipped

with output for powering the sensor and converters with 2 V DC ±5% and

max.current 50 mA for 11...12...16 V DC, 10...12...13 V AC power supply voltage

and max. 200 mA for other power supply voltage.

• Legible graphic display

The 128 x 6 points display with a backlight mounted on front of the unit is a big

advantage of the data recorder available in two colours. It allows the display of trend

graphs for each channel separately. Different operation modes provide the

possibility of selecting and adjusting the method of data presentation depending on

the user's requirements. Data recording intervals are selected by the user from the

menu level. Additionally, it is possible to set the display to show one current value

measured for a selected channel.

• Easy configuration

There are 6 keys on the front of the data recorder that enable the configuration of

the unit. The menu assisted with full text descriptions makes the unit configuration

process quite easy. However, due to a significant number of configured parameters

it is advised to use the attached configuration software for PCs.

User manual - DATA RECORDER SRD-99X and cooperating software

3. TECHNICAL DATA

Power supply voltage

(depending on version)

External fuse (required)

Power consumption

85...230...260 V AC/DC; 50 ÷ 60 Hz (separated),

19...24...50 V DC, 16 V...24...35 V AC (separated)

or 11...12...16 V DC, 10...12...13 V AC (separated)

T - type, max. 2 A

for power supply voltage: 12 V DC max. 12 W,

for other power supply voltage:

typically 7 VA; max. 12 VA

Measurement inputs

(depending on version)

U/I version:

mV/RTD/TC version:

up to 8 inputs 0÷5 V, 1÷5 V, 0÷10 V, 2÷10 V, 0÷20 mA

or ÷20 mA, common ground

up to 8 inputs Pt100, Pt500, Pt1000 (with manual

connection switch 2 or 3-wire), K, S, J, T, N, R, B, E,

0÷60 mV, 0÷75 mV, 0÷100 mV or 0÷150 mV

Digital input 1 input 2 V DC, galvanic isolation

power consumption: 7,5 mA / 2 V,

isolation: 1 min @ 500 V DC.

Digital outputs 2 electronic relays, NO type, 2 V AC / 35 V DC /

max. 200 mA, overload protection

Recording cycle 1 sec./ 2 sec. / 5 sec. / 10 sec. / 15 sec. / 20 sec. /

30 sec. /1 min. / 2 min. / 5 min. / 10 min. / 15 min. /

20 min. / 30 min. / 60 min.

Communication interface RS- 85, 8N1 / Modbus RTU, galvanic isolated

1 min @ 500 V DC,1200 bit/s ÷ 115200 bit/s,

USB PC,

USB Host (in front or in the back of the device) support

for standard USB FlashDrive devices

Display

Backlight color

LCD graphic display, 128 x 6 points, with backlight

white or amber

Data memory 8 MB - version with USB Host interface

Protection level

version without USB interface IP 65 (front panel, optional version with mounting hole

sealing available)

IP 20 (housing and terminals)

version with USB interface IP 5 (front panel, after using waterproof cover)

IP 20 (housing and terminals)

User manual - DATA RECORDER SRD-99X and cooperating software

Housing type

Housing material

Housing dimensions

Mounting hole

Assembly depth

Panel thickness

panel mounting

NORYL - GFN2S E1

96 x 96 x 100 mm

90,5 x 90,5 mm

102 mm

max. 5 mm

Operating temperature

(depending on version)

Storage temperature

(depending on version)

Humidity

Altitude

0 °C to +50 °C (standard)

-20 °C to +50 °C (option)

-10 °C to +70 °C (standard)

-20 °C to +70 °C (option)

5 to 90% no condensation

up to 2000 meters above sea level

Screws tightening max. torque 0,5 Nm

Max. connection leads diameter 2,5 mm2

Safety requirements according to: PN-EN 61010-1

installation category: II

pollution degree: 2

voltage in relation to ground: 300 V AC

insulation resistance: >20 MW

insulation strength between power supply and

input/output terminal: 1 min. @ 2300 V (see Fig. 3.1)

EMC PN-EN 61326-1

Device described in this manual is available in two versions differed by

measurement inputs type. This manual contain following short descriptions:

U/I version - means device with type of inputs: voltage ( 0÷5 V, 1÷5 V, 0÷10 V,

2÷10 V)

current (0÷20 mA, ÷20 mA)

mV/RTD/TC version - means device with type of inputs: TC (K, S, J, T, N, R, B, E)

RTD (Pt100 / Pt500 / Pt1000)

mV (0÷60 mV, 0÷75 mV,

0÷100 mV lub 0÷150 mV)

Parameters of current type inputs ( U/I version )

I put type 0÷5 V, 1÷5 V, 0÷10 V, 2÷10 V, 0÷20 mA or ÷20

mA, common ground

Measurement range ± 9999 plus decimal point

Current measurement accuracy ± 0.1% @ 25 °C; ± one digit (for 0÷10 and 0÷20 mA

range)

Temperature stability 50 ppm / °C

Sampling rate 8 sps

Accepted prolonged input overload 20%

Voltage input resistance 60 kW

Current input resistance 100 W

User manual - DATA RECORDER SRD-99X and cooperating software

Sensor power supply output 2 V DC ± 5% and max. current:

50 mA for power supply voltage 11...12...16 V DC,

10...12...13 V AC,

200 mA for other power supply voltage,

Uninsulated from measurement inputs

Current input protection 50 mA auto-reset fuse

User manual - DATA RECORDER SRD-99X and cooperating software

Parameters of TC, RTD and mV type inputs ( mV/RTD/TC version )

Thermocouple i put K, S, J, T, N, R, B, E

Measurement ranges K:

-200 °C

-328 °F

-50 °C

-58 °F

-210 °C

-3 6 °F

-200 °C

-328 °F

-200 °C

-328 °F

-50 °C

-58 °F

250 °C

82 °F

-200 °C

-328 °F

1370 °C

2 98 °F

1768 °C

321 °F

1200 °C

2192 °F

00 °C

752 °F

1300 °C

2372 °F

1768 °C

321 °F

1820 °C

3308 °F

1000 °C

1832 °F

Measurement accuracy K, J, E: ± 0.1% @ 25 °C; ± one digit

N: ± 0.2% @ 25 °C; ± one digit

S, T, R, B: ± 0.5% @ 25 °C; ± one digit

Accuracy of cold ends temperature

compensation ± 1 °C

RTD i put Pt100, Pt500 or Pt1000 (with manual connection

switch 2 or 3-wire)

Measurement range -100 °C ÷ +600 °C

-1 8 °F ÷ +1112 °F

Measurement accuracy ± 0.1% @ 25 °C; ± one digit

Measurement wires resistance max. 20 W (every wire)

Voltage i put (150 mV) 0÷60 mV, 0÷75 mV, 0÷100 mV, 0÷150 mV

Measurement accuracy ± 0.1% @ 25 °C; ± one digit (for 0÷150 mV range)

Input resistance > 1,5 MW

Accepted prolonged input overload 20,00%

Temperature stability 50 ppm / °C

Display range -999 ÷ 9999 (for RTD mode – see above)

Common ground

Table des matières

Autres manuels Simex Enregistreur de données

Simex

Simex SRD-N16 Manuel utilisateur

Simex

Simex PMS-90R Manuel utilisateur

Simex

Simex SRD-99 Manuel utilisateur

Simex

Simex SRD-99 Manuel utilisateur

Manuels Enregistreur de données populaires d'autres marques

TESTO

TESTO 176 Manuel utilisateur

HT Italia

HT Italia XL421 Manuel utilisateur

HBM

HBM SOMAT XR CX22B-R Manuel utilisateur

Agtrix

Agtrix 380i Manuel utilisateur

Hobo

Hobo H8 Pro Manuel utilisateur

Beijing ART Tech

Beijing ART Tech PCI2320 Manuel utilisateur

Athena

Athena GET SL1 Manuel utilisateur

Motec Systems

Motec Systems C185 Manuel utilisateur

Beijing ART Tech

Beijing ART Tech USB2832 Manuel utilisateur

Rotronic

Rotronic HygroLog HL20 Manuel utilisateur

MRC

MRC DW-6092 Manuel utilisateur

Racelogic

Racelogic VBOX LapTimer Manuel utilisateur

Edu-Logger

Edu-Logger 900-240 Manuel utilisateur

Elma

Elma DT173 Manuel utilisateur

MadgeTech

MadgeTech PRTemp140 Fiche technique

Comet

Comet U0121M Manuel utilisateur

pico Technology

pico Technology PT-104 Manuel utilisateur

Soil Instruments

Soil Instruments GTecLink Manuel utilisateur