SilverNet 7 Series Manuel utilisateur

V1.2 www.silvernet.com

SERIES 7INDUSTRIAL GIGABIT POE+

UNMANAGED SWITCHES

SIL 73204P SIL 73208P

User Manual

 
Network Switches User Manual Table Of Contents 2 
TABLE OF CONTENTS 
Table Of Contents...................................................................................................................... 2 
Introduction............................................................................................................................... 3 
Packing list................................................................................................................................. 3 
The Panels and LED indicators................................................................................................... 4 
Installation................................................................................................................................. 5 
DIN-rail installation................................................................................................................ 5 
Wall-mounted installation..................................................................................................... 5 
Power..................................................................................................................................... 6 
Product Dimension.................................................................................................................... 6 
Copper cable connection........................................................................................................... 7 
Standard RJ45 connector....................................................................................................... 7 
Fibre cable connection .............................................................................................................. 8 
Accessories ................................................................................................................................ 8 
Technical parameters................................................................................................................ 9 
Standards................................................................................................................................. 10 
Warnings.................................................................................................................................. 10 
Troubleshooting ...................................................................................................................... 11 
Responsibility Note.................................................................................................................. 11 
Warranty.................................................................................................................................. 11 
Contact SilverNet..................................................................................................................... 11 
Copyright Information............................................................................................................. 11 
Other SilverNet Products......................................................................................................... 12 

Network Switches User Manual Introduction 3

INTRODUCTION

The SilverNet Series 7 Industrial Gigabit PoE+ Managed Switches are reliable, high

performance, high specification and cost effective Managed industrial switches suitable for

industrial network operations.

The un-managed switches require no configuration and instantly operate as soon as you

power them up. They can be installed by DIN-rail or wall mounted, allowing users greater

flexibility.

The Switches are fully compliant with the IEEE802.3af/at standard, providing Power-over-

Ethernet over twisted pair cables. The fibre optics ports feature a modular SFP slot for any

kind of MSA-compliant pluggable 1.25Gbps SFP transceiver.

PACKING LIST

Please check the following items in the package before installing the device

Industrial PoE+ Switch 1 piece

User manual 1 copy

Serial cable 1 piece

Please contact your distributor immediately for any missing or damaged items.

Network Switches User Manual The Panels and LED indicators 4

THE PANELS AND LED INDICATORS

SIL 73204P and SIL 73208P

Mark

Name

Function

Power LED

“On”: Power is on and normal

System LED

“On”: System is on and normal

SFP Port

“On”: Fibre connection is present

“Blinking”: Data being transmitted

RJ45 Ports

Yellow LED “On”: PoE connection is present

Yellow LED “Blinking”: Data being transmitted

Green LED “On”: Ethernet connected at 1000M

Green LED “Off”: Ethernet connected at 10/100M

Wall kit

Wall mounting bracket

DIN kit

DIN-rail mounting bracket

Wall kit

Wall mounting holes

Ground

Grounding screw

Terminal block

Power input Terminal

Network Switches User Manual Installation 5

INSTALLATION

DIN-RAIL INSTALLATION

Pic 1 Pic 2

The DIN-rail installation is based on Pic 1 and Pic 2.

WALL-MOUNTED INSTALLATION

The wall mount kit is fixed to the back of the switch. Remove and re-attach the wall

mounting kit as shown in the image above.

Attach the switch and bracket to the wall using appropriate screws. Do not completely

tighten the screws, allow approximately 2mm of space.

Place the screw head through the large holes in the wall bracket then pull down to secure,

tighten screws once in place.

Network Switches User Manual Product Dimension 6

POWER

The input terminal of the switch is for 6 PIN plug type terminals, V1+ and V1- is for power

supply 1 (PWR1), V2 + and V2- is for power supply 2 (PWR2) and GND for the earthing

terminal, as shown in image below..

The input voltage range for power 1 and power 2 is 12VDC ~ 56VDC，V1+, and V2+ are

positive, V1- and V2- are negative.

The switch can be powered by two power supplies simultaneously allowing the switch to

continue functioning even if one of the power supplies fails.

Note*

For the SIL 73204P please use power supply SIL NDR 120-48

For the SIL 73208P please use power supply SIL NDR 240-48

PRODUCT DIMENSION

Network Switches User Manual Copper cable connection 7

COPPER CABLE CONNECTION

STANDARD RJ45 CONNECTOR

There are 8 wires on a standard UTP/STP cable, and each wire is colour coded. The following

shows the pin allocation and colour of a straight through cable and crossover cable:

Network Switches User Manual Fibre cable connection 8

FIBRE CABLE CONNECTION

ACCESSORIES

1Gbps Fibre transmission

Part Code

Description

SIL-SFP0-01-25-X850-0-5D

1G Multimode 850nm SFP, 550m

SIL-SFP0-01-25-X131-10XD

1G Singlemode 1310nm SFP, 10km

SIL-SFP0-01-25-X131-40XD

1G Singlemode 1310nm SFP, 40km

SIL-SFP0-01-25-X155-80XD

1G Singlemode 1550nm SFP, 80km

1Gbps BiDi

SIL-SFP0-01-25-B131-10XD

1G SM 1310nm TX FP 10km with DDM, 1550nm RX

SIL-SFP0-01-25-B155-10XD

1G SM 1550nm TX FP 10km with DDM, 1310nm RX

SIL-SFP0-01-25-B139-10XD

1G SM 1310nm TX FP 10km with DDM, 1490nm RX

SIL-SFP0-01-25-B149-10XD

1G SM 1490nm TX FP 10km with DDM, 1310nm RX

SIL-SFP0-01-25-B131-40XD

1G SM 1310nm TX DFB 40km with DDM, 1550nm RX

SIL-SFP0-01-25-B155-40XD

1G SM 1550nm TX DFB 40km with DDM, 1310nm RX

SFP to Ethernet

SIL-SFP0-01-25-XXXT-0-1

1G RJ45 Copper SFP, 100m

Power supplies

Part Code

Description

SIL NDR-120-48

120W 48V 2.5A Industrial Din Rail Power Supply

SIL NDR-240-48

240W 48V 5A Industrial Din Rail Power Supply

SIL NDR-480-48

480W 48V 10A Industrial Din Rail Power Supply

Network Switches User Manual Technical parameters 9

TECHNICAL PARAMETERS

Power supply

Input voltage: 12V～56V (redundant dual power)

PSE Power: 0～30W

POE Pin: 1/2+，3/6-

Copper Port

Connector: RJ-45 connector

Data Rate: 10/100MbpsAuto, 10/100/1000Mbps Auto

Twisted Pair cable: Cat5 UTP cable

Transmission distance: 100 metres

Fibre Port

Connector: SC (default), FC/ST/SFP (optional)

Data Rate: 155Mbps，1.25Gbps

Fibre Type: SM 9/125μm，MM 50/125μm、62.5/125μm

Transmission distance: 20km ~ 120km

Environment

Storage temperature: -40~85℃

Operating temperature: -40~75℃

Relative humidity: 5%-90%

Mechanism

Enclosure: IP40, Black, Metal shell

Mounting: DIN-rail, Wall

Agreement

IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3x

IEEE 802.3af, IEEE 802.3at

Network Switches User Manual Standards 10

STANDARDS

EMI FCC Part 15 Subpart B Class A

EN61000-4-2（ESD）

EN61000-4-3（RS）

EN61000-4-4（EFT）

EN61000-4-5（Surge）

EN61000-4-6（CS）

EN61000-4-8

EN61000-4-11

IEC60068-2-27

IEC60068-2-32

IEC60068-2-6

EN60950-1

WARNINGS

This product is only suitable for indoor applications.

Ensure that the dust caps are placed over the Fibre interface connectors when not in use.

Do not stare directly into the fibre transmitter as this is very dangerous and can cause

serious damage to your eyes.

Optical fibre transceivers must be used in pairs.

Single optical fibre transceivers must be used in pairs (A, B)

A: TX1310/RX1550nm B: TX1550/RX1310nm.

Ce manuel convient aux modèles suivants

Table des matières

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur