Signode CU-25LH Mode d’emploi

IMPORTANT - DO NOT DESTROY THIS MANUAL. It is the customer's responsibility to have all operators and

service personnel read and understand this manual. Contact your local Signode representative for additional copies

of this manual.

GENERAL SAFETY INSTRUCTIONS

READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO

FOLLOW THESE INSTRUCTIONS CAN RESULT IN SEVERE

PERSONAL INJURY.

GENERAL CONSIDERATIONS

1. EYE INJURY HAZARD.

Failure to wear safety glasses with side

shields can result in severe eye injury or

blindness. Always wear safety glasses

with side shields which conform to ANSI

Standard Z87.1 or EN 166.

2. Strap applied to a package is under tension and will

rebound in an outward direction when cut.

3. Before using the cutter read its operation and safety

instructions.

4. Use the correct Signode strap cutter for your application;

if you need help contact your Signode representative.

Never use a claw hammer, crowbar, chisel, ax, or similar

tool to cut or break strap. Such tools will cause the strap

to fly apart with hazardous force.

5. Keep work areas uncluttered and well lit.

6. Maintain proper footing and balance when cutting strap.

Do not cut strap when you are in an awkward position.

Take additional care when cutting ties on compressed

loads; strap will recoil with a much greater force. Be

careful when cutting straps as the load can shift.

7. Strap should always be cut square; strap cut at an angle

has a much sharper end.

8. Dispose of all cut strap. Never leave it lying on the

ground where it can present a tripping hazard. Never re-

use strap.

9. Take good care of the cutter. Inspect it daily for worn or

damaged cutting surfaces. Do not use this tool if these

surfaces are worn or damaged.

10. Always wear protective gloves when

handling strap or sharp parts.

CU-25LH STRAP CUTTER

Part No. 022654

For cutting all strap up to 2" x .050" (50mm x

1.27mm).

CUTTING TENSIONED STRAP

1. Keep personnel at safe distance, away from possible

flying strap ends.

2. Stand to one side of the strap as it is being cut, OUTSIDE

OF THE DANGER ZONE (dotted area).

3. Cut strap.

CU-25LH PARTS LIST

Key Qty Part No. Description

1* 1 005744 Top cutter blade

2** 2 003911 Flexloc nut, thin 5/16-24 std.

31 161177 Top handle assembly

4 2 005753 Bolt 5/16-24 x 1-5/16

5 1 005745 Handel link

6 1 005746 Cutter lever

7 1 005748 Cutter drive pin

8 1 161178 Bottom handle assembly

9** 2 005747 Cutter lever bolt

10 1 005743 Bottom cutter blade

11** 1 005749 L. H. bolt

12 2 020378 Handel grip

* Can be reversed when worn.

** Use Loctite #271 on threads only.

!Apply a light machine oil to all moving parts of this tool.

!When ordering parts, please show tool model, part number and name.

!Wearing parts are underlined and should be stocked.

!Common hardware parts may obtained at any local hardware supply.

Ce manuel convient aux modèles suivants

Autres manuels Signode Outils

Signode

Signode B/91001 Manuel utilisateur

Signode

Signode Josef Kihlberg B560PN Manuel utilisateur

Signode

Signode Josef Kihlberg F560PN Manuel utilisateur

Signode

Signode Josef Kihlberg JK35T590 Manuel utilisateur

Signode

Signode Josef Kihlberg B561PN Manuel utilisateur

Signode

Signode Josef Kihlberg R555PN Manuel utilisateur

Signode

Signode Josef Kihlberg JK20V779L22 Manuel utilisateur

Signode

Signode Josef Kihlberg R557PN Manuel utilisateur

Signode

Signode AHP-34 Mode d’emploi

Signode

Signode PNSC-2 Mode d’emploi

Signode

Signode TENSION-WELD VT-16HD Mode d’emploi

Signode

Signode Josef Kihlberg JK20-680FN Manuel utilisateur

Signode

Signode JOSEF KIHLBERG B53PN Manuel utilisateur

Signode

Signode TENSION-WELD VXT2-19 Mode d’emploi

Signode

Signode AMPT-12 Mode d’emploi

Signode

Signode TENSION-WELD VT-19HD Mode d’emploi

Signode

Signode SCM-12 Mode d’emploi

Signode

Signode VT-16 Mode d’emploi

Signode

Signode JOSEF KIHLBERG JK10-680 Manuel utilisateur

Signode

Signode Josef Kihlberg JK20A680L Manuel utilisateur

Signode

Signode Tension-Weld BTS-16 Mode d’emploi

Signode

Signode Josef Kihlberg JK20V779L Manuel utilisateur

Signode

Signode PRHM-34 Mode d’emploi

Signode

Signode PN2-2 Mode d’emploi

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser