Signode LITTLE DAVID LX600 Manuel utilisateur
Label Application System
LX600 Apply Only Labeling System
PN: LSMANUAL-LX600
Version: 05B (For use with the Allen-Bradley Micro830 ™ PLC)
Operator’s Manual
LABEL APPLICATION SYSTEM
Labeler Operation
Copyright Loveshaw 2014-2020
LOVESHAW
2206 Easton Turnpike, PO. Box 83
South Canaan, PA 18459
Tel: 1-800-962-2633 • 570-937-4921
Fax: 570-937-4016
www.loveshaw.com
Loveshaw Europe
Unit 1 Newton Park
West Portway Industrial Estate
Andover, Hampshire SP10 3SH
ENGLAND
Tel: 264-357511
Fax: 264-355964
Tuesday, March 10, 2020
The information contained in this manual is correct and accurate at the time of its publication. LOVESHAW reserves the right
to change or alter any information or technical specifications at any time and without notice.
©2014--2020 LOVESHAW. All rightsreserved Printed in the United States of America
Table of Contents
Chapter 1: Introduction
Chapter 2: Operating Safety
Chapter 3: Overview
Chapter 4: Installation and Threading
Section 1: Placing the Mount.
Section 2: Threading the Label Stock
Chapter 5: Theory of Operation
Chapter 6: Product Sensing and Time Delay
Chapter 7: Applicators and Gap Sensor
Gap Sensor and Label Placement to Peel Edge
Standard Straight Tamp Cylinder (200mm stroke)
Optional Extended Straight Tamp Cylinders (350/400/500/600mm stroke)
Dual Tamp / CW (Swing Arm / Rotary Actuator Applicator)
Chapter 8: Pneumatic System
Air Filter and Shutoff
In Line Air Filters
Chapter 9: Features and Options
Warning Light Assembly
Cleanable Vacuum Filter
Air Dryer
Spare Parts Kits
Chapter 10: Controller Operation
Chapter 11: Maintenance
Chapter 12: Warranty and Label Converting Specifications
Chapter 13: Assemblies and Schematics
SEE SECTION FOR DETAILED ORGANIZATION OF DRAWINGS
Introduction
hank you for purchasing the Little David™ model LX600 series
Apply Only labeler. The LX600 series apply only labelers are
designed to be versatile enough to suit a variety of carton labeling
requirements with one standard unit. All employees who will be
required to operate the labeler should read this manual to ensure proper set-
up, operating safety and a long machine life. After reading this manual you
will know how to perform the following functions,
How to position the labeler to achieve maximum performance.
How to thread the labeler and adjust the sensors to apply labels in the
most efficient manner.
How to use the controller interface.
Troubleshooting and replacing of worn or defective parts.
Throughout this manual there are several illustrations designed to help
you perform the variety of tasks described. These illustrations all depict the
right-hand version of the machine. You can tell a right hand and left hand
machine apart by facing the machine. The side with the plate holding all of
the rollers is the hand version of the machine. The hand designation of your
individual machine does not affect any of the procedures or maintenance
operations described below only that your left hand machine appears as a
mirrored image of the machine depicted in the illustrations.
Chapter
1
T
ICON KEY
Important information
Operating Safety
Observe the warnings and cautions
below when using the Little David Label
Application Systems. Within this manual, a warning
indicates that the potential for bodily injury exists, and a
caution indicates when the machine may suffer damage.
Instruction: Requirement for System Operation
Socket-outlet shall be installed near the equipment and shall
be easily accessible.
Fuses marked MDA 5A are of type: 250V, 5 Amp, Slow Blow.
Fuses marked MDA 10A are of type: 250V, 10 Amp, Slow Blow.
Warning: Potential Bodily Injury
Always turn off the electrical power before clearing jams, and before
performing maintenance. Use Proper Lock Out / Tag Out
Procedures. Never operate unit without guards in place.
Avoid liquid or excessive moisture when using the system. Do not
operate the system with wet hands, nor in a very humid environment.
Do not spill liquid on the system.
Do not touch moving parts. Turning hubs can bruise or scrape,
rapidly moving label stock can cut like a knife.
If a problem arises that is not covered in this manual, do not attempt
to repair the system yourself, instead, call your nearest service office for
immediate and correct care of the equipment. Trained personnel
should perform all adjustments and service.
Chapter
2
Instruction:
Instruction:
W
arning:
Warning:
Warning:
Warning:
P/N:SL‐0041
This manual contains operator information for Little David LX600 Label
Application Equipment. It is directed toward the person who operates that
system. You should take the time to read through this manual once before
operating it. Thereafter, refer to it as necessary.
Take special note of all warnings, cautions, and maintenance instructions.
Like any other piece of equipment, the Little David LX600 Label Application
System functions best when cared for and used carefully. Note that only an
authorized technician should perform any procedures not described in this
manual.
Caution: Potential Machine Damage
Do not install the system in direct sunlight.
Do not install the system near a heater or heat emitting equipment.
Provide and use proper electrical power. Clean / noise free electrical
power is required for proper / trouble free operation.
Do not operate, maintain, or otherwise use the system, except as
described in this manual.
Safety Decal Locations
Caution:
Caution:
Caution:
Caution:
Safety Decal Locations
Safety Decal Part Number
Labeler Sections
Overview
This manual covers several parts of the machine. The following
diagram identifies the key sections of the machine.
Chapter
3
Table des matières
