SIGMA TEK DI 080 Manuel utilisateur

DI 080

S-DIAS Digital Input Module

Instruction Manual

Date of creation: 17.02.2014

Version date: 26.07.2023

Article number: 20-006-080-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: office@sigmatek.at

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS DIGITAL INPUT MODULE DI 080

26.07.2023 Page 1

S-DIAS Digital Input Module DI 080

with 8 inputs

The S-DIAS digital input module DI 080 is equipped with eight inputs and

a +24 V signal for reading the signal states “0“ and “1“. Input filters are

available to suppress noise signals occurring in the signal lines.

DI 080 S-DIAS DIGITAL INPUT MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Digital Input Specifications........................................................13 
5.2 Electrical Requirements.............................................................13 
5.3 Miscellaneous .............................................................................15 
5.4 Environmental Conditions.........................................................15 
6Mechanical Dimensions........................................................16 
7Connector Layout..................................................................17 

 S-DIAS DIGITAL INPUT MODULE DI 080 
 
07.2023 Page 3 
1 Status LEDs.................................................................................17 
2 Applicable Connectors...............................................................18 
3 Label Field...................................................................................19 
8Wiring.....................................................................................20 
1 Wiring Example...........................................................................20 
2 Note..............................................................................................21 
9Assembly/Installation ...........................................................22 
1 Check Contents of Delivery.......................................................22 
2 Mounting......................................................................................23 
Addressing.............................................................................25 
Supported Cycle Times ........................................................26 
1 Cycle Times below 1 ms (in µs).................................................26 
2 Cycle Times equal to or higher than 1 ms (in ms)...................26 
Transport/Storage .................................................................27 
Storage...................................................................................27 
Maintenance...........................................................................28 
1 Service.........................................................................................28 
2 Repair...........................................................................................28 
Disposal .................................................................................28 

DI 080 S-DIAS DIGITAL INPUT MODULE

Page 4 26.07.2023

16 Hardware Class DI080 ...........................................................29

16.1 Interfaces.....................................................................................30

16.1.1 Clients ...............................................................................................30

16.1.2 Servers..............................................................................................30

16.1.3 Communication Interfaces.................................................................30

16.2 Example.......................................................................................31

S-DIAS DIGITAL INPUT MODULE DI 080

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x DI 080

DI 080 S-DIAS DIGITAL INPUT MODULE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS DIGITAL INPUT MODULE DI 080

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

DI 080 S-DIAS DIGITAL INPUT MODULE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Table des matières

Autres manuels SIGMA TEK Système d'E/S

SIGMA TEK

SIGMA TEK IPN 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK FC 021 Manuel utilisateur

SIGMA TEK

SIGMA TEK TO 127 Manuel utilisateur

SIGMA TEK

SIGMA TEK DI 200 Manuel utilisateur

SIGMA TEK

SIGMA TEK DI 204 Manuel utilisateur

SIGMA TEK

SIGMA TEK AO 081 Manuel utilisateur

SIGMA TEK

SIGMA TEK IO 011S Manuel utilisateur

SIGMA TEK

SIGMA TEK AI 040 Manuel utilisateur

SIGMA TEK

SIGMA TEK AI 075 Manuel utilisateur

SIGMA TEK

SIGMA TEK SRO 022 Manuel utilisateur

SIGMA TEK

SIGMA TEK C-DIAS Manuel d'instructions

SIGMA TEK

SIGMA TEK AI 046 Manuel utilisateur

SIGMA TEK

SIGMA TEK TO 081 Manuel utilisateur

SIGMA TEK

SIGMA TEK CO 041 Manuel utilisateur

SIGMA TEK

SIGMA TEK AO 026 Manuel utilisateur

SIGMA TEK

SIGMA TEK SDI 101 Manuel utilisateur

SIGMA TEK

SIGMA TEK CSTO 082 Manuel utilisateur

SIGMA TEK

SIGMA TEK CP 931 Manuel utilisateur

SIGMA TEK

SIGMA TEK SR 012 Manuel utilisateur

SIGMA TEK

SIGMA TEK C-DIAS Series Manuel utilisateur

SIGMA TEK

SIGMA TEK AI 088-1 Manuel utilisateur

SIGMA TEK

SIGMA TEK DI 160 Manuel utilisateur

SIGMA TEK

SIGMA TEK SDI 101 Manuel utilisateur

SIGMA TEK

SIGMA TEK DM 811 Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur