SIGLENT SHS800X Series Manuel utilisateur
SHS800X
SHS1000X
Handheld Digital
Oscilloscope
QS_EN01D
Quick Start
SHS800X&SHS1000X Quick Start I
Copyright Information
Declaration
SIGLENT products are protected by patent law in and outside of P.R.C.
SIGLENT reserves the right to modify or change parts of or all the specifications or pricing policies at
the company's sole decision.
Information in this publication replaces all previously corresponding material.
Any method of copying, extracting or translating the contents of this manual is not allowed without the
permission of SIGLENT.
Note: SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD.
SHS800X&SHS1000X Quick Start II
Contents
COPYRIGHT INFORMATION..............................................................................................................I
GENERAL SAFETY SUMMARY........................................................................................................1
SAFETY TERMS AND SYMBOLS.....................................................................................................1
MEASUREMENT CATEGORY...........................................................................................................2
QUICK START ....................................................................................................................................3
INTRODUCTION OF SCOPE PANEL................................................................................................7
INTRODUCTION OF METER PANEL..............................................................................................12
INTRODUCTION OF RECORDER PANEL......................................................................................14
INTERFACE GLANCE......................................................................................................................17
TROUBLE SHOOTING.....................................................................................................................18
SHS800X/SHS1000X Quick Start 1
General Safety Summary
Carefully read the safety precautions in user’s manual to avoid any personal injury or damage the
instrument and avoid any products connected to it. To avoid potential hazards, please use the
instrument as specified.
Safety Terms and Symbols
The meaning of symbols
symbol
meaning
symbol
meaning
Warning
Power Switch
Hazardous Voltage
Equipment meeting double
insulation or reinforced
insulation
EarthGround
Indoor use only
Lithium battery failure
EU label for separately
recycled electrical and
electronic equipment
Cue and its meaning
DANGER
Indicates direct injury or hazards that may happen.
WARNING
Indicates potential injury or hazards that may happen.
CAUTION
Indicates potential damage to the instrument or other property that may happen.
2 SHS800X/SHS1000X Quick Start
Measurement Category
IEC61010-2-030 defines the measurement category to rate the ability of measuring instruments to
withstand short-term transient overvoltage outside of the working voltage. This product and its
accessories can only be used in the environment of the nominal measurement category.
0-An instrument with no rated measurement category is used to measure circuits that are not
directly connected to the mains, such as a circuit board powered by a battery or a secondary
circuit with special protection. This measurement category is also called CATⅠ.
CAT II：
For measurements installed in buildings, such as junction boxes, circuit breakers, distribution
boards and equipment permanently connected to fixed installations.
CAT III:
Used for measurements installed in buildings, such as junction boxes, circuit breakers,
distribution boards and equipment that are permanently connected to fixed installations.
CAT IV:
It is used for measuring at the source of low-voltage devices, such as electricity meters and
primary overcurrent protection devices.
SHS800X/SHS1000X Quick Start 3
Quick Start
Product Appearance
SHS800X
SHS1000X
4 SHS800X/SHS1000X Quick Start
Battery Installation
To protect the battery from over discharging, the battery may be delivered separately. Please install
the battery before use as follows:
1. Remove the three screws on the battery cover with a screwdriver, as shown in Figure 1.
2. Remove the battery cover, as shown in Figure2.
3. Put the battery into the battery slot, as shown in Figure3.
4. Lock the screws with the screwdriver, as shown in Figure 1, and then turn on the oscilloscope to
check whether the battery is installed successfully.
5. Connect the DC-DC adapter to the connector on the left side (top view) of the oscilloscope and
charge the battery to a full state the first time power on.
Figure 1
Figure 2
Figure 3
SHS800X/SHS1000X Quick Start 5
Measurement Connection
The SHS800X and SHS1000X series handheld oscilloscope measurement accessories include
oscilloscope probes, multimeter probes, current adapters.
1. Oscilloscope probe
All oscilloscope probes should be properly compensated before their first use with the oscilloscope.
The following steps illustrate the proper probe compensation procedure.
1) Connect probe to the CH1 Input Terminal and the Compensation Signal Output Terminal on the
right side panel.
2) Check the displayed waveforms and compare them with the following figure.
3) Adjust the probe until the waveform matches the "Compensated Correctly”waveform above.
Under
Compensated
Compensated
Correctly
Over
Compensated
6 SHS800X/SHS1000X Quick Start
2. Multimeter probe
Before using the multimeter probe，please select the measuring range of the multimeter first, then
plug the red probe and black ( grounding terminal ) probe into the corresponding input terminals
according to the marking prompt of the front panel. When measuring the current, please select the
correct accessories according to the current.
3. Current Adapter
To test current, insert a current adapter between the meter input and the meter probe. There are two
different adapters, SCD600MA and SCD10A, which have built-in sampling resistors and fuses, can
be used with the multimeter's mA meter and Ameter respectively.
Autres manuels pour SHS800X Series
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels SIGLENT Équipement de test
SIGLENT
SIGLENT SDS1022DL Manuel utilisateur
SIGLENT
SIGLENT SDS5000X Series Manuel utilisateur
SIGLENT
SIGLENT SHS800 series Manuel utilisateur
SIGLENT
SIGLENT SDG2000X Series Manuel utilisateur
SIGLENT
SIGLENT SDS1000X+ Series Manuel utilisateur
SIGLENT
SIGLENT SDS2000X-E Series Manuel utilisateur
SIGLENT
SIGLENT SDS2352X-E Manuel utilisateur
SIGLENT
SIGLENT SDS1204X HD Manuel utilisateur
SIGLENT
SIGLENT SDS2000X-E Series Manuel utilisateur
SIGLENT
SIGLENT SDS1000CFL Series Manuel utilisateur
SIGLENT
SIGLENT SDS1000 Series Manuel utilisateur
SIGLENT
SIGLENT SDS1000CML series Manuel utilisateur
SIGLENT
SIGLENT SDS2000X Series Guide d'installation
SIGLENT
SIGLENT SHS800X Series Manuel utilisateur
SIGLENT
SIGLENT SDS1072CML Manuel utilisateur
SIGLENT
SIGLENT SDS1000X Series Manuel utilisateur
SIGLENT
SIGLENT SDS2304X Manuel utilisateur
SIGLENT
SIGLENT SDS1000X-E Series Manuel utilisateur
SIGLENT
SIGLENT SDS2000X Series Manuel utilisateur
SIGLENT
SIGLENT SDS1000X-E Series Manuel utilisateur
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
