Sierra Wireless PinPoint XT Manuel utilisateur

CoverTitle

PinPoint XT

Quick Start Guide

for Sprint

20070914

Rev 1.0A

Rev 1.0A Mar.10 23

Activating your PinPoint XT on Sprint

Network

•OMA-DM

•Hands Free

Activation (HFA)

•Activating PinPoint

•Updating PinPoint

XT firmware

•Configuring through

ACEmanager

•Hardware

Installation

•Power

•Indicator Lights This Quick Start guide provides step-by-step directions for activating

your PinPoint XT on Sprint’s network.

Tip:

For additional configuration options, refer to the User Guide for your

PinPoint XT.

OMA-DM

PinPoint XT is an embedded router solution that supports Network

Initiated (NI) OMA-DM Device Configuration (DC) and PRL Updates

(PRL) on the Sprint network. The PinPoint XT firmware registers

notifications with the MC5727 radio module for OMA-DM NI alerts

and session state and processes them appropriately. The alert

response instructs the radio module to immediately process the NI

OMA-DM command. When the OMA-DM session state is IDLE,

PinPoint XT records the session type and session result code and

then re-establishes the data connection.

Hands Free Activation (HFA)

PinPoint XT automatically detects the radio module installed during

system startup. If the radio module is CDMA technology, PinPoint XT

will check the current provisioning state and if necessary execute

HFA. For devices that have previously been provisioned the HFA

routine is bypassed.

Rev 1.0A Mar.10 24

Activating PinPoint XT

To activate your PinPoint XT, follow the instructions below:

1. Connect the PinPoint XT with antennas.

2. Plug the power cable to the power connector on the back panel of

the PinPoint XT.

3. Connect your computer to the PinPoint XT with an ethernet

cable.

4. Observe the LEDs, as indicated in Chapter 4, Indicator Lights

section.

Wait approximately 30 seconds, to allow the PinPoint XT to initialize

and go over the air.

Updating PinPoint XT firmware

For installing the latest firmware version (.exe file), you can go to the

Sierra Wireless website: http://www.sierrawireless.com/support.

For the updater tool to execute, please install the USB drivers

available on the website before executing the .exe file.

Tip:

Copy the USB Serial Driver.inf file to your desktop. Then power up the

PinPoint XT and connect USB. Install from specific location and point to this

.inf file. For detailed instructions on installing the USB drivers, please refer to

Universal Serial Bus Application Note.

1. Connect the PinPoint XT to your computer using anUSB cable.

2. Connect the power adapter and antennas to your PinPoint XT.

3. Install the PinPoint XT executable file by running the .exe file and

follow the prompts.

a. A Sierra Wireless firmware update welcome screen appears.

Click on Next.

Rev 1.0A Mar.10 25

Figure 0-1: Launch Screen

b. Choose the interface you want to program the modem

through and click on Next.

Note: You can use Boot interface only when a serial cable connection is

established.

The default private for Ethernet is also in a different subnet from the

other connection types.

*can be changed via ACEmanager

Table 0-1: Factory Defaults

Interface PinPoint XT Connected Device

Ethernet Private default 192.168.13.31* 192.168.13.100

USB/NET 192.168.14.31 192.168.14.100

DUN 192.168.15.31 192.168.15.100

Wi-Fi* 192.168.17.31 192.168.17.100

Rev 1.0A Mar.10 26

Figure 0-2: Configuration: Interface selection

c. The next screen will prompt you to reset the modem

manually. Click on Next after resetting the modem manually.

Installation begins and can take up to a few minutes.

Once the installation is complete, you will get a confirmation screen.

Verifying USB connection

Verify that your USB is connected as USB/net by checking the

Network Connections window in your computer.

Rev 1.0A Mar.10 27

Figure 0-3: Verify USB Connection

Confirming IP Address

Check the IP Address in your Local Area Connection window.

Figure 0-4: Confirm IP Address

Configuring through ACEmanager

ACEmanager is a free utility. Follow the steps below to connect to

ACEmanager for configuring the modem.

•Ensure PinPoint XT connectivity to access ACEmanager.

Rev 1.0A Mar.10 28

•Go to: http://192.168.13.31:9191 the first time you connect to

ACEmanager.

An alternate method to configure and activate your PinPoint XT is by

using AT commands sent directly to the modem with a terminal

application.

Caution:

It is not possible to activate the PinPoint XT using either

ACEmanager or AceNet.

1. Set telnet timeout in to 20 minutes.

2. Save the telnet setting.

3. Enter the user name of your account (NAI). The user name is

usually expressed as an email address with phone number of the

account (example, 1234567@carrier.com). This information

should be provided by your carrier. You may not need this step.

AT*NETUID=[NAI]

4. Enter the password of your account. This information should be

provided by your carrier. You may not need this step.

AT*NETPW=[password]

5. Verify ALEOS has established communication to the internal

hardware.

6. Enter the activation command appropriate for your type of

account. The SID and NID are optional and only required if your

account type uses them.

·If you have the same number for the MIN and MDN or MSID:

AT*PROVISION=MSL,MDN[,SID,NID]

·If you have the different numbers for the MIN and MDN or

MSID:

AT*PROVISION2=MSL,MDN,MIN/MSID[,SID,NID]

Using Direct Commands to the Internal

Hardware

Use only if the ALEOS method is unsuccessful.

Activating the Modem

1. Put modem into passthru mode to by-pass ALEOS. This will

allow direct communication with the wireless module for

programming. Entering passthru will take 10-15 seconds and

will return an ‘OK’ when it is complete.

AT\APASSTHRU

2. Verify you are in Passthru mode.

AT!STATUS

3. Unlock the module.

AT~NAMLCK=MSL

Rev 1.0A Mar.10 29

4. Set the MDN and MSID.

AT~NAMVAL=0,MDN,MSID,0,65535

5. Verify the settings are what you intended to enter.

AT~NAMVAL?0

6. Reset the module.

AT!RESET

7. Press the reset button on the front of the modem. When the

modem restarts, it should register on the network.

Hardware Installation

Note: During installation,

please be sure that the

cables are secure but do

not bear any additional

weight that could loosen

the connector from the

unit.

Your PinPoint XT should be mounted in a position that allows easy

access for the cables so they are not bent, constricted, in close

proximity to high amperage, or exposed to extreme temperatures.

The LEDs on the front panel should be visible for ease of operational

verification. You should ensure that there is adequate airflow around

the modem but that it is kept free from direct exposure to the

elements, such as sun, rain, dust, etc.

Caution:

The PinPoint XT is in a hardened case and designed for use in

industrial and extreme environments. However, unless you are using cables

expressly designed for such environments, they can fail if exposed to the

same conditions the PinPoint XT can withstand.

Figure 0-5: PinPoint XT Connectors

Cellular

Rev 1.0A Mar.10 30

Note: This device is not

intended for use within

close proximity of the

human body. Antenna

installation should provide

for at least a 20 CM

separation from the

operator.

Antennas selected should not exceed a maximum gain of 5 dBi under

standard installation configuration. In more complex installations

(such as those requiring long lengths of cable and/or multiple

connections), it’s imperative that the installer follow maximum dBi

gain guidelines in accordance with the radio communications

regulations of the Federal Communications Commission (FCC),

Industry Canada, or your country’s regulatory body (if used outside

the US).

Your PinPoint XT will work with most cellular antennas with a

connector. Connect the primary antenna or primary RF cable directly

to the antenna connector on the back of the PinPoint XT.

Tip:

When using a cable to an antenna placed away from the modem,

minimize the length of your cable. All gain from a more advantageous

antenna placement can be lost with a long cable to the modem.

Your PinPoint XT will work with most standard active GPS antennas.

Connect the GPS antenna or cable directly to the threaded SMA

connector.

Mount the GPS Antenna in the vehicle. The less the cable is wrapped

and bound together, the better it will perform. Place it on the roof, or

on the dash, or rear panel where it has a good view of the sky

(greater than a 90 angle view of the sky).

There are three options for antenna mounts:

•Magnetic roof-mount

•Through glass-mount

•Permanent mount

Figure 0-6: GPS Antenna Placement for a Vehicle

Note: Your PinPoint XT does not have a second antenna for received

diversity. Received diversity is disabled by default.

Rev 1.0A Mar.10 31

Warning:

Risk of electric shock: Only use the supply voltages listed in

this user guide.

Warning:

When using AC to DC adapter the ambient temperature should

not exceed 40

Your PinPoint XT can be used with either DC or AC, with the

appropriate power adapter. DC cables and AC adapters are available

as optional accessories in addition to the one included with your

PinPoint XT.

The cable included with your PinPoint XT, is a DC cable with Standby

Ignition Sense which connects to the 20-pin I/O connector. Other

optional accessory cables include:

•A DC power cable with a DB-9 female serial connector (P/N 120-

140-1021)

•A DC power cable with I/Os (P/N 120-140-1022),

•A fused DC power cable (P/N 120-140-1023),

•A DC power cable with a battery-charger circuit

•An auxiliary battery connector (P/N 120-140-1024)

•A DC power cable with 4-pin adaptor (P/N 120-140-1025) which

connects to AC adaptor (P/N 120-100-1013).

The DC power cable positive lead should be connected to the battery

or power source positive terminal. The power cable negative lead

should be connected to the battery or power source negative

terminal.

The PinPoint XT has an internal polysilicon circuit breaker that opens

at 0.5 to 1.0 amps of current.

If you wish to use the Standby Ignition Sense (SISE) feature of your

PinPoint XT, the wire of the DC power cable should be used to

connect to your ignition. When SISE is enabled in the modem and the

ignition sense connector is wired to your vehicle, the ignition sense

will provide a link to the modem to enable it to enter a low-power,

standby mode when your vehicle is turned off and power up more

quickly when the ignition is started.

Warning:

Explosion Hazard - Do not disconnect equipment unless power

has been switched off or the area is known to be non-hazardous.

Autres manuels pour PinPoint XT

Table des matières

Autres manuels Sierra Wireless Routeur réseau

Sierra Wireless

Sierra Wireless AirLink Raven XE Manuel utilisateur

Sierra Wireless

Sierra Wireless AirLink LX40 Manuel d'installation

Sierra Wireless

Sierra Wireless RAVEN 20080605 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK HELIX 2140847 Manuel utilisateur

Sierra Wireless

Sierra Wireless LX60 Manuel utilisateur

Sierra Wireless

Sierra Wireless AirLink GX Series Manuel utilisateur

Sierra Wireless

Sierra Wireless RX55 Manuel utilisateur

Sierra Wireless

Sierra Wireless AirLink RV55 Manuel d'installation

Sierra Wireless

Sierra Wireless RX55 Manuel d'installation

Sierra Wireless

Sierra Wireless Raven XE Manuel utilisateur

Sierra Wireless

Sierra Wireless AirLink MP70 Manuel utilisateur

Sierra Wireless

Sierra Wireless Airlink MG90 Manuel utilisateur

Sierra Wireless

Sierra Wireless Airlink MG90 Manuel utilisateur

Sierra Wireless

Sierra Wireless AirLink MP70 Manuel d'installation

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité