Siemens 7LF4 4210 Guide de démarrage rapide

N 292229/02 251426.41.05c

Technical data

7LF4 4210 7LF4 4211 7LF4 4212

Supply voltage: 230V 50/60Hz 120V 50/60Hz 24V AC/DC ±10%

Effective power consumption: Approx. 1 W

Contact rating: 1 changeover contact 16A 250V~µ cos ϕ= 1

Parallel compensation: 60VA max. 7µF

Accuracy: ± 0,2 s / day under typical installation conditions

single strand multi strand

Terminal capacity: 1,5...4 mm21,5...2,5 mm2

Programmes : 56

Pulse start times: 84 (only if pulse function is activated)

Pulse duration: 1s … 59min 59s

Battery reserve: 6 years

Storage ambient: -20°C to +60°C

Working ambient: -20°C to +55°C

General information

• Start-up: after applying the supply voltage, the time switch

starts automatically with the last selected function. The relay

position is set by the current program.

• Battery backup

- Backlighting not active

- Data key READ/WRITE only via the menu.

Set language

Overview



Day, Time, Date

Switch status

Function

Receptacle for

data key

1800W 1800W 1800W 2300W 100W 100W 1800W 2300W

Overview of programmed

switching times for the week.

Resolution 0.5h

Select menu, back to main menu,

Hold down > 1s = operating display

Confirm selection or load parameters

Select menu options or set parameters

Safety notes

This product may be installed only by a qualified electrician. Non-compliance may result in a fire hazard or electric shocks. Before installation, read

the operating instructions and observe the product-specific requirements for the installation location. Use only original spare parts for repair and

maintenance. Unauthorised opening and repair by other persons will invalidate all claims for liability, replacement or warranty services.

7LF4 4210

7LF4 4211

7LF4 4212

1/4

Modes Reset

Warning!

The memory will be cleared,

and all set data will be lost.

Hold down all keys simultaneously for about 2 seconds

and release.

The language, time, date, summertime/wintertime and

switching times will have to be re-entered.

•Auto - Automatic operation

•Constant ON

•Constant OFF

•Extra

The switch status imposed by the

program is inverted (manual override).

With the next effective switch command,

the time switch resumes control of on/off

switching.





Programming

MENU OK

Set time/date, summertime/wintertime and holiday period



Holiday

After activation, the holiday program is executed between 0:00h on the start date and 24:00h on the end date

(Constant ON/OFF). After the holiday program has run once, it must be reactivated.

Summertime: ± 1 hour

Europe: Factory set.

SPECIAL: The switchover to/from

summertime can be freely programmed by

entering a start date and end date

and is then executed each year on

the same day of the week, e.g.

Sunday.

A program consists of an ON time, OFF time and associated ON and OFF days.

Programs with predefined on/off days (Mon to Sun, Mon to Fri and Sat and Sun): for these programs, you only need to set the switching times.

With the "INDIVIDUAL” option, you can allocate switching times to specific days of your choice.

The programs of a channel are linked to one another by logical OR.

CHRONO = All switch commands are executed in chronological order in a week

INPUT = Programs are executed in the order in which they are entered

Additional function descriptions are provided on the attached sheet.

Set MON and TUES

as on/off days

2/4









Contrast adjustment

Data key

Hour counter

Random function

Load the programs of the time switch on to a data key (WRITE KEY)

Warning! all programs already existing on the data key will be overwritten.

Load the programs from the data key to the time switch (READ KEY)

Warning! all programs already programmed in the time switch will be overwritten.

Displays the total relay ON time, from 0 to 65535 h, and the date of the last reset.

Function active: the programmed switching cycles are shifted at random within the range of ± 30 minutes.

3/4

1s … 59min 59s

Activating the pulse function

Activating the pulse function

Pulse duration

Pulse start time activation

Pulses are also started during power failures. Aafter the power has been restored they are output for the remaining running time.

Overlapping pulses restart the pulse start time. When switching from PASSIVE to ACTIVE, the program memory is cleared.

4/4

Ce manuel convient aux modèles suivants

Autres manuels Siemens Changer

Siemens

Siemens SIRIUS 3SE6315 BB0 Series Manuel utilisateur

Siemens

Siemens SCALANCE XM-400 Feuille d'instructions

Siemens

Siemens SCALANCE XR-100WG Series Manuel utilisateur

Siemens

Siemens 5ST3062 Manuel utilisateur

Siemens

Siemens RUGGEDCOM RP110 Manuel utilisateur

Siemens

Siemens SCALANCE X-200 Manuel utilisateur

Siemens

Siemens ASC77.2U Manuel utilisateur

Siemens

Siemens Pointek CLS200 Manuel utilisateur

Siemens

Siemens 3TS11 Series Manuel utilisateur

Siemens

Siemens 5WG1 221-2EB Series Manuel utilisateur

Siemens

Siemens Sirius 3RT1926-2E Manuel utilisateur

Siemens

Siemens Sitrans WM100 Manuel utilisateur

Siemens

Siemens SIRIUS S0 Manuel utilisateur

Siemens

Siemens SIMATIC NET RUGGEDCOM RS900 Manuel utilisateur

Siemens

Siemens SENTRON 3KC0 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200S Manuel utilisateur

Siemens

Siemens 3VF9322 0 Series Manuel utilisateur

Siemens

Siemens SIRIUS 3RT2.2 Series Manuel utilisateur

Siemens

Siemens SIMATIC NET RUGGEDCOM RS900F Manuel utilisateur

Siemens

Siemens 5-FSV-350 Manuel du propriétaire

Siemens

Siemens QPL Series Manuel utilisateur

Siemens

Siemens 3KA50 Manuel utilisateur

Siemens

Siemens RUGGEDCOM RSG920P Manuel utilisateur

Siemens

Siemens SIRIUS Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur