Siemens SIPROTEC 4 7VK61 Manuel utilisateur

SIPROTEC 4

Breaker Management

Device 7VK61

V4.7 and higher

Manual

C53000-G1176-C159-5

Preface

Open Source Software

Table of Contents

Introduction 1

Functions 2

Mounting and Commissioning 3

Technical Data 4

Ordering Information and Accessories A

Terminal Assignments B

Connection Examples C

Default Settings and Protocol-dependent

Functions D

Functions, Settings, Information E

Literature

Glossary

Index

NOTE

For your own safety, observe the warnings and safety instructions contained in this document, if available.

Disclaimer of Liability

This document has been subjected to rigorous technical

review before being published. It is revised at regular inter-

vals, and any modifications and amendments are included

in the subsequent issues. The content of this document has

been compiled for information purposes only. Although

Siemens AG has made best efforts to keep the document as

precise and up-to-date as possible, Siemens AG shall not

assume any liability for defects and damage which result

through use of the information contained herein.

This content does not form part of a contract or of business

relations; nor does it change these. All obligations of

Siemens AG are stated in the relevant contractual agree-

ments.

Siemens AG reserves the right to revise this document from

time to time.

Document version: V04.21.00

Edition: 05.2018

Version of the product described: V4.7 and higher

The disclosure, duplication, distribution and editing of this

document, or utilization and communication of the content

are not permitted, unless authorized in writing. All rights,

including rights created by patent grant or registration of a

utility model or a design, are reserved.

Trademarks

SIPROTEC™, DIGSI™, SIGUARD™, SIMEAS™, and SICAM™

are registered trademarks of Siemens AG. Any unauthor-

ized use is illegal. All other designations in this document

can be trademarks whose use by third parties for their own

purposes can infringe the rights of the owner.

Preface

Purpose of this Manual

This manual describes the functions, operation, installation, and commissioning of devices 7VK61. In partic-

ular, one will find:

•Information regarding the configuration of the scope of the device and a description of the device func-

tions and settings → Chapter 2;

•Instructions for Installation and Commissioning → Chapter 3;

•Compilation of the Technical Data → Chapter 4;

•As well as a compilation of the most significant data for advanced users → Appendix.

General information with regard to design, configuration, and operation of SIPROTEC 4 devices are set out in

the /1/ SIPROTEC 4 System Description.

Target Audience

Protection-system engineers, commissioning engineers, persons entrusted with the setting, testing and main-

tenance of selective protection, automation and control equipment, and operating personnel in electrical

installations and power plants.

Applicability of this Manual

This manual applies to: SIPROTEC 4 Breaker Management Device 7VK61; firmware version V4.7 and higher.

Angaben zur Konformität

This product complies with the directive of the Council of the European Communities on the

approximation of the laws of the Member States relating to electromagnetic compatibility

(EMC Council Directive 2004/108/EC) and concerning electrical equipment for use within

specified voltage limits (Low-voltage directive 2006/95 EC).

This conformity is proved by tests conducted by Siemens AG in accordance with the Council

Directives in agreement with the generic standards EN61000-6-2 and EN 61000-6-4 for the

EMC directive, and with the standard EN 60255-27 for the low-voltage directive.

The device has been designed and produced for industrial use.

The product conforms with the international standard of the series IEC 60255 and the German

standard VDE 0435.

Additional Standards IEEE Std C37.90 (see Chapter 4, Technical Data")

[ul-schutz-110602-kn, 1, --_--]

SIPROTEC 4, 7VK61, Manual 3

C53000-G1176-C159-5, Edition 05.2018

Additional Support

For questions about the system, please contact your Siemens sales partner.

Support

Our Customer Support Centre provides a 24-hour service.

Tel: +49 (180) 524-7000

Fax: +49 (180) 524-2471

E-Mail: [email protected]

Training Courses

Inquiries regarding individual training courses should be addressed to our Training Centre:

Siemens AG

Siemens Power Academy TD

Humboldtstraße 59

90459 Nürnberg

Germany

Tel: +49 (911) 433-7415

Fax: +49 (911) 433-7929

E-Mail: [email protected]

Internet: www.siemens.com/poweracademy

Notes on Safety

This document is not a complete index of all safety measures required for operation of the equipment (module

or device). However, it comprises important information that must be followed for personal safety, as well as

to avoid material damage. Information is highlighted and illustrated as follows according to the degree of

danger:

DANGER

DANGER means that death or severe injury will result if the measures specified are not taken.

²Comply with all instructions, in order to avoid death or severe injuries.

WARNING

WARNING means that death or severe injury may result if the measures specified are not taken.

²Comply with all instructions, in order to avoid death or severe injuries.

CAUTION

CAUTION means that medium-severe or slight injuries can occur if the specified measures are not taken.

²Comply with all instructions, in order to avoid moderate or minor injuries.

Preface

4 SIPROTEC 4, 7VK61, Manual

C53000-G1176-C159-5, Edition 05.2018

NOTICE

NOTICE means that property damage can result if the measures specified are not taken.

²Comply with all instructions, in order to avoid property damage.

NOTE

Important information about the product, product handling or a certain section of the documentation

which must be given particular attention.

Qualified Electrical Engineering Personnel

Only qualified electrical engineering personnel may commission and operate the equipment (module, device)

described in this document. Qualified electrical engineering personnel in the sense of this manual are people

who can demonstrate technical qualifications as electrical technicians. These persons may commission,

isolate, ground and label devices, systems and circuits according to the standards of safety engineering.

Proper Use

The equipment (device, module) may be used only for such applications as set out in the catalogs and the

technical description, and only in combination with third-party equipment recommended and approved by

Siemens.

Problem-free and safe operation of the product depends on the following:

•Proper transport

•Proper storage, setup and installation

•Proper operation and maintenance

When electrical equipment is operated, hazardous voltages are inevitably present in certain parts. If proper

action is not taken, death, severe injury or property damage can result:

•The equipment must be grounded at the grounding terminal before any connections are made.

•All circuit components connected to the power supply may be subject to dangerous voltage.

•Hazardous voltages may be present in equipment even after the supply voltage has been disconnected

(capacitors can still be charged).

•Operation of equipment with exposed current-transformer circuits is prohibited. Before disconnecting the

equipment, ensure that the current-transformer circuits are short-circuited.

•The limiting values stated in the document must not be exceeded. This must also be considered during

testing and commissioning.

Typographic and Symbol Conventions

The following text formats are used when literal information from the device or to the device appear in the

text flow:

Parameter Names

Designators of configuration or function parameters which may appear word-for-word in the display of the

device or on the screen of a personal computer (with operation software DIGSI), are marked in bold letters in

monospace type style. The same applies to titles of menus.

1234A

Parameter addresses have the same character style as parameter names. Parameter addresses contain the

suffix A in the overview tables if the parameter can only be set in DIGSI via the option Display additional

settings.

Parameter Options

Possible settings of text parameters, which may appear word-for-word in the display of the device or on the

screen of a personal computer (with operation software DIGSI), are additionally written in italics. The same

applies to the options of the menus.

Preface

SIPROTEC 4, 7VK61, Manual 5

C53000-G1176-C159-5, Edition 05.2018

Indications

Designators for information, which may be output by the relay or required from other devices or from the

switch gear, are marked in a monospace type style in quotation marks.

Deviations may be permitted in drawings and tables when the type of designator can be obviously derived

from the illustration.

The following symbols are used in drawings:

Device-internal logical input signal

Device-internal logical output signal

Internal input signal of an analog quantity

External binary input signal with number (binary input,

input indication)

External binary output signal with number

(example of a value indication)

External binary output signal with number (device indication) used as

input signal

Example of a parameter switch designated FUNCTION with address

1234 and the possible settings ON and OFF

Besides these, graphical symbols are used in accordance with IEC 60617-12 and IEC 60617-13 or similar.

Some of the most frequently used are listed below:

Analog input variable

AND-gate operation of input values

OR-gate operation of input values

Exclusive OR gate (antivalence): output is active, if only one of the

inputs is active

Coincidence gate: output is active, if both inputs are active or inactive

at the same time

Dynamic inputs (edge-triggered) above with positive, below with

negative edge

Formation of one analog output signal from a number of analog input

signals

Limit stage with setting address and parameter designator (name)

Timer (pickup delay T, example adjustable) with setting address and

parameter designator (name)

Preface

6 SIPROTEC 4, 7VK61, Manual

C53000-G1176-C159-5, Edition 05.2018

Timer (dropout delay T, example non-adjustable)

Dynamic triggered pulse timer T (monoflop)

Static memory (SR flipflop) with setting input (S), resetting input (R),

output (Q) and inverted output (Q), setting input dominant

Static memory (RS-flipflop) with setting input (S), resetting input (R),

output (Q) and inverted output (Q), resetting input dominant

Preface

SIPROTEC 4, 7VK61, Manual 7

C53000-G1176-C159-5, Edition 05.2018

8 SIPROTEC 4, 7VK61, Manual

C53000-G1176-C159-5, Edition 05.2018

Open Source Software

The product contains, among other things, Open Source Software developed by third parties. The Open

Source Software used in the product and the license agreements concerning this software can be found in the

Readme_OSS. These Open Source Software files are protected by copyright. Your compliance with those

license conditions will entitle you to use the Open Source Software as foreseen in the relevant license. In the

event of conflicts between Siemens license conditions and the Open Source Software license conditions, the

Open Source Software conditions shall prevail with respect to the Open Source Software portions of the soft-

ware. The Open Source Software is licensed royalty-free. Insofar as the applicable Open Source Software

License Conditions provide for it you can order the source code of the Open Source Software from your

Siemens sales contact - against payment of the shipping and handling charges - for a period of at least 3 years

since purchase of the Product. We are liable for the Product including the Open Source Software contained in

it pursuant to the license conditions applicable to the Product. Any liability for the Open Source Software

beyond the program flow intended for the Product is explicitly excluded. Furthermore any liability for defects

resulting from modifications to the Open Source Software by you or third parties is excluded. We do not

provide any technical support for the Product if it has been modified.

SIPROTEC 4, 7VK61, Manual 9

C53000-G1176-C159-5, Edition 05.2018

10 SIPROTEC 4, 7VK61, Manual

C53000-G1176-C159-5, Edition 05.2018

Table des matières

Autres manuels Siemens Dispositif de protection

Siemens

Siemens 7SJ82 Manuel utilisateur

Siemens

Siemens Siprotec 7SD600 Guide de l'utilisateur

Siemens

Siemens 6AV6881-0AJ21-0AA0 Manuel utilisateur

Siemens

Siemens SINAMICS PERFECT HARMONY GH180 Manuel de la liste des pièces

Siemens

Siemens Siprotec 7SD600 Guide de l'utilisateur

Siemens

Siemens Solkor 7PG2113 Manuel utilisateur

Siemens

Siemens SENTRON Manuel utilisateur

Siemens

Siemens siprotec 7SA522 Manuel utilisateur

Siemens

Siemens SIPROTEC 7SK80 Manuel utilisateur

Siemens

Siemens SLIM Manuel utilisateur

Siemens

Siemens SENTRON 3VL160X Guide de l'utilisateur

Siemens

Siemens Reyrolle 7SR5 Manuel utilisateur

Siemens

Siemens SIPROTEC 5 Manuel utilisateur

Siemens

Siemens SIPROTEC 5 7UM85 Manuel utilisateur

Siemens

Siemens Cerberus Pyrotronics CP2341 Manuel utilisateur

Siemens

Siemens SIPROTEC 4 7UT6 Series Manuel utilisateur

Siemens

Siemens 7PG21 Solkor Rf Manuel utilisateur

Siemens

Siemens SENTRON 3VL series Guide de l'utilisateur

Siemens

Siemens SINOVA Manuel utilisateur

Siemens

Siemens 7UM515 Manuel utilisateur

Siemens

Siemens SIPROTEC 7SS60 Manuel utilisateur

Siemens

Siemens 7SR51 Guide d'application

Siemens

Siemens SIPROTEC 4 Manuel utilisateur

Siemens

Siemens SCALANCE S612 Manuel utilisateur

Manuels Dispositif de protection populaires d'autres marques

Sola HD

Sola HD STV100K Series Manuel utilisateur

socomec

socomec COUNTIS AMd Manuel utilisateur

Kemo Electronic

Kemo Electronic M148-24 Manuel utilisateur

SK ClickClick Manuel utilisateur

Endress+Hauser

Endress+Hauser HAW569 Manuel utilisateur

Ultrasonic

Ultrasonic SonicPRO Manuel utilisateur

nxt

nxt BIA-nXt-DPC 1-22 Manuel utilisateur

TFortis

TFortis SG-Switch Manuel utilisateur

BERNINI DESIGN

BERNINI DESIGN Be172 Manuel utilisateur

Rayleigh Instruments

Rayleigh Instruments RI-ENERGYSET-3P-ESS-50-100 Manuel utilisateur

GE Multilin 3 Series Manuel utilisateur

E.K.T.

E.K.T. ke-DP01 Manuel utilisateur

cias

cias MICRO-RAY Manuel utilisateur

Sungrow

Sungrow PVS-16MH Manuel utilisateur

Reer

Reer 32010 Manuel utilisateur

Tyco

Tyco ESFR-17 Manuel utilisateur

Ross

Ross Opengear SRA-8901-R Manuel utilisateur

GE Multilin 850 Manuel utilisateur