Siemens FIDAMAT 5E Manuel utilisateur
Contents Page
1 Introduction 4
1.1 General 4
1.2 Staff Qualifications 4
2 Application 5
3 Design 6
4 Mode of Operation 7
5 Technical Data 8
6 Installation 12
6.1 Mounting 12
6.2 Gas Supply 12
6.3 Electric Connections 13
7 Startup, Calibration 19
7.1 Startup 19
7.1.1 FIDAMAT5E-E,5E-A 19
7.1.2 FIDAMAT5E-I 19
7.1.3 FIDAMAT5E-AS 20
7.2 Calibration 20
7.3 Automatic Calibration 20
8 Operation 23
8.1 Description of Control Panel 23
8.2 Input Example 24
8.3 Coding and Organization of Operating Function Groups 25
8.4 Organization of Data Storage 26
9 Maintenance, Warnings and Error Messages 27
9.1 Maintenance 27
9.2 Warnings and Error Messages 28
9.2.1 Warnings 28
9.2.2 Faults 30
10 Spare Parts and Accessories 33
11 Appendix A-1
11.1 Gas Flow Diagrams A-1
11.2 Layout Diagrams of Important Electronic Components A-5
11.3 Summary of Operating Functions A-6
11.4 Special Sheet for Storage of Current Coding A-35
2
Note
Your attention is drawn to the fact that the contents of this Instruction Manual are not part of a
previous or existing agreement, commitment or statutory right and do not change these. All
commitments on the part of Siemens are contained in the respective sales contract which also
contains the complete and solely applicable warranty conditions. These warranty conditions in the
contract are neither extended nor limited by the contents of this Instruction Manual.
Also notethat forclarity reasonsthis InstructionManual cannotdescribe everypossible problem in
conjunction with the use in systems. Should you require further information, or should particular
problems occur which are not handled in sufficient depth in this Manual, help can be requested
through your local Siemens office or representative.
TermswiththefollowingmeaningsareusedinthisInstructionManualandinthewarninginformation
on the product:
Danger in the sense of this Manual and the warning information on the product itself means that
death, severe personal injury and/or substantial damage to property will occur if the appropriate
safety precautions are not observed.
Warningin the sense of this Manual and the warning information on the product itself means that
death, severe personal injury and/or substantial damage to property can occur if the appropriate
safety precautions are not observed.
Caution in the sense of this Manual and the warning information on the product itself means that
slight personal injury and/or damage to property can occur if the appropriate safety precautions
are not observed.
A notein the sense of this Manual is important information on the product or the respective part of
the Manual to which particular attention should be paid.
3
1 Introduction
1.1 General
Warning! Certainpartsinthiselectricaldevicecontaindangerousvoltagesduring
operation.
Failure to observe the warnings could therefore result in severe personal
injuryand/ordamage toproperty.
Onlysuitablyqualifiedstaffshouldworkonthisdeviceorinitsvicinity.These
shouldbe thoroughly familiar with allwarnings and maintenance measures
accordingto this Manual.
Correct and safe operation of this device is dependent on proper handling,
installation,operationandmaintenance.
This device has left the factory in a perfect condition as regards safety. The notes and warnings in
thisManualmustbeobservedbytheuserifthisstateistobemaintainedandhazard-freeoperation
of the device assured.
1.2 StaffQualifications
A qualified person in the sense of this Instruction Manual and the warning information is one who
isfamiliarwiththeinstallation,constructionandoperationofthedeviceandwhohastheappropriate
qualifications,e.g.:
– is trained and authorized to energize, de-energize, ground and tag circuits and devices in
accordance with established safety practices;
– is trained in the proper care and use of protective equipment in accordance with established
safetypractices;
– is trained in first aid.
4
2 Application
The FIDAMAT 5E is an analyzer for measuring total hydrocarbons. It operates according to the
principle of flame ionization.
The analyzer is suitable for measuring all gaseous hydrocarbons. A heated line must be used for
the connection to prevent condensation and adsorption in the gas line.
Warning! Explosivegasmixturesmust not bemeasuredusingtheFIDAMAT.The ana-
lyzermustnotbeusedinpotentiallyexplosiveatmospheres.
Order No. Analyzertype
7MB1420-1 FIDAMAT 5 rack-mounted unit and bench-top unit for emission measurements
7MB1420-0 FIDAMAT 5 rack-mounted unit and bench-top unit for ambient measurements
7MB1420-2 FIDAMAT5 rack-mounted unitfor measurements withH2/He as combustion gas
7MB1420-4 FIDAMAT5rack-mountedunitfor shedmeasurements
5
3 Design
The device is available either as a bench-top unit fitted in a housing, or without a housing for
installation in a 19-inch rack or 19-inch cabinet.
TheFIDAMATcomprisestwomainsections,theanalyzersectionandtheelectronicswithfrontpanel
controls.
Analyzersection
The analyzer section consists of the oven with sample gas filter, detector chamber and various
restrictors.The ovenis accessiblefrom thesideto enablemodifications orrepairs tobe carried out
in the installed condition without loosening the electric connections or gas piping connections.The
sample gas filter is accessible from the front when the front panel has been folded out.
The analyzer section also contains the diaphram pump with separate oven for the pump head.The
pump can be dismounted from the front without having to open the oven.
The analyzer section also contains pressure regulators, solenoid valves, pressure sensors and a
flowsensor.
Electronics
The electronics consist of the input board which is integrated into the front panel, the motherboard
with preamplifier board and the control board.
Themotherboard contains theEPROMs forthe software, theEEPROM for theparameter sets and
the switch for the write-protected area on the EEPROM.
6
4 Mode of Operation
Electrons are released when hydrocarbons are combusted in a hydrogen flame. These electrons
are collected at an electrode by means of an electric field and measured using a highly sensitive
amplifier. The current is proportional to the quantity of organically-bound C atoms in the sample
gas.
A diaphram pump draws the sample gas and generates a specific pressure. The sample gas is
passed into the measuring chamber via an obstruction-resistant fused silica restrictor.Thesample
gasismixed in themeasuring chamber withhydrogenorhydrogen/helium (4:6)and with a specific
amount of air and routed via the nozzle into the combustion chamber.
The hydrogen pressure is held constant by a pressure regulator. The balanced system of pump,
restrictors and pressure regulators ensures that the sample gas pressure is kept constant.
TheFIDAMAT operates largelyautomatically. Iftheparameters (pressures,temperatures) areset,
thedevicestartsupautomaticallywhen switched onandigniteswhenthesetpoint temperaturehas
been reached. The hydrogen and combustion air pressures are measured when switching on, and
the control panel indicates if they are incorrectly set.
1 Flame
2 Quartz nozzle
3 Combustion air
4 Sample gas
5H
2
6 Measuring electrode
7 Amplifier
Fig. 4 Principle of flame ionization detector
-200 V DC
6
7
2
3
4
5
1
7
5 Technical Data
Number of measuring ranges Max.4,freelyparameterizable
Switching ratio Optional
Autoranging Selectable
Hysteresis:
–Switchover to larger range at 90 % of span of
smallerrange
–Switchover to smaller range at 80 % of span of
smallerrange
Output signals Atterminal stripsX1, X2andX3.
A cable with a plug connector
(OrderNo.W79070-U1610-M25)canbe connected
to these terminal strips
Analog 0/2/4 to 20 mA, max. resolution 0.1 %,
max. load 750 Ω
Digital RS232serialinterfaceasV.24orTTY(20mA)
Programming facilities (for setting of
device-specific parameters using control panel) Oven and pump temperatures, limits, measuring
ranges,measured-valuestorage,timeconstant,
3-stage code for protection against unauthorized
and unintentional use etc.
Device output Floating contacts for:
–Measure/calibratesignal
–Ready/notreadysignal
–4selectable limit relays,max. 24 V/1A, freely
assignableto measuringranges
–4 contacts for range identification, max. 24 V/1 A
–Solenoid valve control, max. 24 V/1 A
Deviceinput 4 floating contacts are required for range switching,
span calibration,
zero calibration,
autocal
Measured-valuedisplay Digital concentration display (5 digits with floating
decimal point)
Resolution of digital display 0.1%of measuredvalue
Ripple of output signal <0.5 % of 10 ppm C1with5E-E
Noise <0.5 % of 10 ppm C3with5E-E
<0.5 % of 10 ppm C3with5E-Aand5E-AS
<0.5 % of 10 ppm C1with5E-I
Detection limit 0.1 ppm C1with5E-E
0.1 ppm C1with5E-Aand5E-AS
0.1 ppm C1with5E-I
8
Repeatability 0.1to 1 %of full-scalevalue, range-dependent
Characteristic Linearization error <1 % of f.s.v.
Long-term drift
Zero
5E-E <2 % of span/week with f.s.v. >10 ppm C1,
range-dependent
5E-A,5E-AS <2 % of span/week with f.s.v. >10 ppm C3,
range-dependent
5E-I < 2 % of span/day with f.s.v. 2 ppm C1, range-
dependent
Span As for zero
Responsetime(T90 time) with time
constant 0 s, set using function 13 <1 s without filter
2 to 3 s with filter
Warm-uptime Approx. 2 to 3 hours
Analyzerchambertemperature 110to200˚C,freely-selectable
Permissiblestoragetemperature –30 to +70 ˚C
Permissibleambienttemperature (operation) 5 to 45 ˚C
Inlet pressure for hydrogen, combustion air,
zero gas and calibration gas(es) 3 bar (45 psig) above atmospheric pressure
Position of use Front panel vertical
Change in display through influencing variables
Mains voltage variations (+10, -15 %) <1 % of measured value
Ambienttemperaturevariations <1 % of measured value/10 K
Atmosphericpressurevariations <1 % of measured value /50 mbar
Frequencyvariations <1 % of measured value for the permissible
frequency range
Influence of position <1 % of measured value with inclination <15˚
Power supply
Mains connection AC110,120,220,230,240V,48to63Hz
Power consumption Approx. 350 VA in start-up phase,
approx. 150 VA during operation
Degree of protection
Rack-mountedunit IP20to DIN40050
Bench-top unit IP21to DIN40050
Dimensions Seedimensionaldrawing
Weight 28 kg
Material of parts in contact with sample gas PTFE,quartz(nozzle,fusedsilica),graphite
(gaskets),stainlesssteel1.4571(316SS)
9
Gas consumption data
5E-E
Combustion gas Approx. 350 ml/min (approx. 21 l/h)
Hydrogen Approx. 20 ml/min (approx. 1.2 l/h)
Samplegas Approx. 1 l/min (approx. 60 l/h)
Zero gas/calibration gas Approx. 2 l/min (approx. 120 l/h)
5E-A(samplegas atstandardpressure)
Combustion gas Approx. 350 ml/min (approx. 21 l/h)
Hydrogen/helium Approx. 110 ml/min (approx. 6.6 l/h)
Samplegas Approx. 1 l/min (approx. 60 l/h)
Zero gas/calibration gas Approx. 2 l/min (approx. 120 l/h)
5E-AS
Combustion gas Approx. 350 ml/min (approx. 21 l/h)
Hydrogen/helium Approx. 110 ml/min (approx. 6.6 l/h)
Samplegas Approx. 1 l/min (approx. 60 l/h)
Zero gas/calibration gas Approx. 2 l/min (approx. 120 l/h)
5E-I
Combustion air: None
Hydrogen Approx. 30 ml/min (approx. 1.8 l/h)
Samplegas Approx. 1 l/min (approx. 60 l/h)
Zero gas/calibration gas Approx. 2 l/min (approx. 120 l/h)
Oxygencross-sensitivity 5E-E: Approx. 30 ppm C1
Length Max. 30 m
Temperature 140to200˚C,freely-selectable
Power consumption (operation) Approx.150VA
Power consumption (startup) Approx.350VA
10
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Siemens Instrument de mesure
Siemens
Siemens 7MC3040-... Manuel utilisateur
Siemens
Siemens Clinitek Advantus Manuel
Siemens
Siemens Synco 700 RMZ785 Manuel de l'opérateur
Siemens
Siemens SICAM Q200 7KG97 Manuel utilisateur
Siemens
Siemens SITRANS LG260 Manuel utilisateur
Siemens
Siemens SEM3 Manuel utilisateur
Siemens
Siemens SITRANS F M MAG 5000 Manuel utilisateur
Siemens
Siemens SITRANS F US SONO 3300 Manuel utilisateur
Siemens
Siemens VDO E-Tacho 1323.01 Manuel utilisateur
Siemens
Siemens SITRANS FUH1010 Manuel utilisateur
Siemens
Siemens Sitrans F Series Manuel utilisateur
Siemens
Siemens SITRANS F Guide de l'administrateur
Siemens
Siemens RAPIDLAB 248 Manuel utilisateur
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
Siemens
Siemens SIMATIC HMI TP1000F Mobile RO Manuel utilisateur
Siemens
Siemens SITRANS F Mode d'emploi
Siemens
Siemens CSI Host Driver Manuel utilisateur
Siemens
Siemens SD 270 Manuel utilisateur
Siemens
Siemens WSM5 Series Manuel utilisateur
Siemens
Siemens Sitrans LR200 Guide de l'utilisateur
