Siding Tools Industries UK-12 Manuel utilisateur

Trancheuse pour

revêtement mural

de 12

MANUEL D’UTILISATION

12" Siding shear

OWNER’S MANUAL

AVERTISSEMENT

Lire et Comprendre toutes les

directives. Le non-respect des directives

décrites ci-dessous peut causer des

blessures graves.

VEUILLEZ CONCERVER CES

DIRECTIVES POUR REFERENCE

ULTERIEURE.

WARNIG

Read and understand all

instructions. Failure to follow all

instructions listed below may

result in serious bodily injury.

SAVE THESE

INTRUCTIONS FOR

FUTURE REFERENCE

UK-12

-1-

SAFETY RULES FOR THE 12" SIDING SHEAR

1. READ AND UNDERSTAND THIS INSTRUCTION MANUALBEFORE

OPERATINGTHE12"WALL COVERING CUTTER.

2. The 12’’ Siding Shear comes with a 1 year warranty. To activate your

warranty, we invite you to register on our website in the service tab at :

sidingtoolsindustries.com

If you are not thoroughly familiar with the operation of the 12" Wall

Covering Cutter,obtainadvicefromaqualifiedworkerorcall450-527-

7840

Stay alert. Do not operate while under the influence of drugs, alcohol, or

medication.

Alwayswearsafety approvedeye protectionwith sideshields(ANSIZ87.1)

Keepwork areaandfree of debris.

Keepchildren andunauthorized persons away from the 12" WallCovering

Cutter and workarea.

Make sure tool is secure. Operate only on a firm substrate or solid stand.

Use the right tool. Do not force the 12" Wall Covering Cutter or use it for a

job for which it was not designed; use only on approved materials.

10.

Keep blade sharp. A dull blade will not perform properly.

11.

Always keep hands away from blade while operating or carrying.

12.

Do not alter or misuse this tool. The 12" Wall Covering Cutter is

precision built; modifications not specified in this manual may result in

a dangerous condition.

13.

Maintain the 12" Wall Covering Cutter with care. Keepblade sharpand

clean. Follow instructions for lubricating and changing accessories.

14.

Useonlyrecommendedaccessories.Theuseofimproperaccessoriesmay

causehazardsorinjury.

15.

Never leave the 12"Wall Covering Cutter unattended. Secure the handle

with the safety lock when not in use.

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS

INJURY! USING THIS MACHINE WITH RESPECT AND CAUTION WILL

CONSIDERABLY LESSEN THE POSIBILITY OF PERSONAL INJURY.

SET UP

-2-

Installation of the Cutter

Install

the front cross bar to the cutter base

with the two bolts and nuts

provided, as

shown.

Warning:

Do not put your fingers

against the sharp edge of the blade

at any time.

CUTTING

-3-

Cutting Preparation

Detach the safety clip from the

handle.

Warning:

Do not put your fingers

against the sharp edge of the

blade at any time.

Cutting Preparation

Secure the blade to lock the

mechanism.

Lift the handle and position the

blade in the locked position

Warning:

Do not put your

fingers against the sharp edge

of the blade at any time.

Cutting Preparation

The mechanism is locked when the

pivot is raised upwards as shown in

the picture. To do this, raise the

handle to its highest and manipulate

the pivot manually

Warning:

Do not put your

fingers against the sharp edge

of the blade at any time.

CUTTING

-4-

Cutting Preparation

Slide the profile into the

predefined block for the type of

profile to be cut. Put the blade in

the cutting position by raising the

handle very high to unlock the

mechanism, then down the handle

to cut.

Warning:

Do not put your

fingers against the sharp edge

of the blade at any time.

Cutting Preparation

Before cutting, reposition the pivot

downwards in the working

position. To do this, raise the

handle to its highest and

manipulate the pivot manually.

Warning:

Do not put your

fingers against the sharp edge

of the blade at any time.

-5-

MAINTENANCE

Maintenance

For any service, it is recommended to

contact Siding Tools Industries at 450-

527-7840

Warning:

It is recommended to

lubricate the blade on a regular

period of time with PL-100 or

equivalent. Do not use WD-40.

Block change according to the material

to cut

Keep the slicer closed. Remove the 4

screws from the bottom of the base.

Warning:

Do not put your fingers

against the sharp edge of the

blade at any time.

Block change according to the material

to cut

Disengage the pivot pin. Raise the handle

and the blade to clear the block

completely.

Warning:

Do not put your fingers

against the sharp edge of the

blade at any time.

-6-

MAINTENACE

Block change according to the material

to be cut

Clear the block completely. Hold

or attach the blade holder to

secure it in the raised position.

Remove the blocks. Position

another block according to the

material to cut. Screw the 4

screws lightly.

Warning:

Do not put your fingers

against the sharp edge of the

blade at any time.

Block change according to the material

to be cut

Lower the blade to the cutting

position to validate the alignment

of the block. Tighten the 4 block

fixing screws.

Warning:

Do not put your fingers

against the sharp edge of the

blade at any time.

Block change according to the material

to be cut

Re-engage the pivot pin.

Warning:

Perform a cut test

before proceeding to validate the

alignment of the blade with the

block.

-7-

MAINTENACE

Blade lade change

Disengage the pivot pin. Raise the handle

and the blade to clear the block

completely.

Warning:

Do not put your fingers

against the sharp edge of the

blade at any time.

Blade change

Clear the block completely.

Remove the 4 bolts to remove the

blade. Position the new blade and

slightly refit the 4 bolts.

Warning:

Do not put your fingers

against the sharp edge of the

blade at any time

Blade change

Lower the blade to the cutting

position to confirm the alignment

of the blade. Tighten the 4 bolts.

Warning:

Do not put your fingers

against the sharp edge of the

blade at any time

-8-

MAINTENACE

Block change according to the material

to be cut

Re-engage the pivot pin.

Warning:

Perform a cut test

before proceeding to validate the

alignment of the blade with the

block.

Transport

Attach the safety clip to the

handle. If the tie is in good

condition, you can lift the shear by

the handle. If not, it is advisable to

raise with two hands by the base.

The weight of the shears is about

55lbs.

Warning:

Secure the safety clip.

For transport by lifting the base,

pay attention to the tip of the

blade protruding at the front.

-9-

OVERAL DIMENSION

Table des matières

Langues :

Autres manuels Siding Tools Industries Coupeur

Siding Tools Industries

Siding Tools Industries ProKUT6 Manuel utilisateur

Manuels Coupeur populaires d'autres marques

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manuel utilisateur

Makita

Makita DCS552 Manuel utilisateur

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manuel utilisateur

Makita

Makita 4112HS Manuel utilisateur

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manuel utilisateur

Hitachi

Hitachi CM 4SB2 Guide de dépannage

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manuel utilisateur

GCC Technologies

GCC Technologies AFJ-24S Manuel utilisateur

DeWalt

DeWalt XR LI-ION DCS350N Manuel utilisateur

Baudat

Baudat ES1 Manuel utilisateur

Mafell

Mafell ZAF 200 Mode d’emploi

Makita

Makita 4100NH Manuel utilisateur

Formax

Formax FD 574 Manuel utilisateur

EINHELL

EINHELL TE-MA 1500 Manuel utilisateur

Husqvarna

Husqvarna Cut-n-Break K 760 Manuel utilisateur

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manuel utilisateur

TRI tool

TRI tool 301A Manuel utilisateur

Roller

Roller King 1 1/4 Manuel utilisateur