SICK WS24-2 Series Manuel utilisateur

BETRIEBSANLEITUNG

WS/WE24-2

Kompakt-Lichtschranken

OPERATING INSTRUCTIONS

WS/WE24-2

Compact photoelectric sensors

Described product

W24-2

WS/WE24-2

Manufacturer

SICK AG

Erwin-Sick-Str. 1

79183 Waldkirch

Germany

Legal information

This work is protected by copyright. Any rights derived from the copyright shall be

reserved for SICK AG. Reproduction of this document or parts of this document is

only permissible within the limits of the legal determination of Copyright Law. Any modi‐

fication, abridgment or translation of this document is prohibited without the express

written permission of SICK AG.

The trademarks stated in this document are the property of their respective owner.

Original document

This document is an original document of SICK AG.

2006/42/EC

SAFETY

OPERATING INSTRUCTIONS

8008782.1DMA/2022-07-12 | SICK O P E R A T I N G I N S T R U C T I O N S | WS/WE24-2 3

Subject to change without notice

Contents

1 About this document................................................................................ 5

2 Safety information.................................................................................... 6

3 Product description.................................................................................. 6

4 Mounting................................................................................................... 7

5 Electrical installation................................................................................ 8

6 Additional functions.................................................................................. 11

7 Commissioning......................................................................................... 12

8 Devices with special features.................................................................. 14

9 Troubleshooting........................................................................................ 14

10 Disassembly and disposal....................................................................... 14

11 Maintenance............................................................................................. 14

12 Technical data........................................................................................... 14

13 Annex......................................................................................................... 16

OPERATING INSTRUCTIONS

4O P E R A T I N G I N S T R U C T I O N S | WS/WE24-2 8008782.1DMA/2022-07-12 | SICK

Subject to change without notice

1 About this document

1.1 Further information

You can find the product page under the Product ID at: pid.sick.com/{P/N}.

P/N corresponds to the part number of the product.

The following information is available depending on the product:

•Data sheets

•These publication in all available languages

•CAD files and dimensional drawings

•Certificates (e.g., declaration of conformity)

•Other publications

•Software

•Accessories

1.2 Symbols and document conventions

Warnings and other notes

DANGER

Indicates a situation presenting imminent danger, which will lead to death or serious

injuries if not prevented.

WARNING

Indicates a situation presenting possible danger, which may lead to death or serious

injuries if not prevented.

CAUTION

Indicates a situation presenting possible danger, which may lead to moderate or minor

injuries if not prevented.

NOTICE

Indicates a situation presenting possible danger, which may lead to property damage if

not prevented.

NOTE

Highlights useful tips and recommendations as well as information for efficient and

trouble-free operation.

Instructions to action

bThe arrow denotes instructions to action.

1. The sequence of instructions is numbered.

2. Follow the order in which the numbered instructions are given.

✓The tick denotes the results of an action.

OPERATING INSTRUCTIONS

8008782.1DMA/2022-07-12 | SICK O P E R A T I N G I N S T R U C T I O N S | WS/WE24-2 5

Subject to change without notice

2 Safety information

2.1 General safety notes

2.1.1 Safety notes

■Read the operating instructions before commissioning.

■

Connection, mounting, and setting may only be performed by skilled per‐

son.

■

2006/42/EC

SAFETY

Not a safety component in accordance with the EU Machinery Directive.

■

When commissioning, protect the device from moisture and contamination.

■These operating instructions contain information required during the life cycle of

the sensor.

2.2 Notes on UL approval

The device shall be supplied from an isolating transformer having a secondary overcur‐

rent protective device that complies with UL 248 to be installed in the field rated either:

a) max 5 amps for voltages 0 ~ 20 V (0 ~ 28.3 V peak), or

b) 100 / Vp for voltages of 20 ~ 30 V (28.3 ~ 42.4 V peak).

Alternatively, they can be supplied from a Class 2 power supply.

UL Environmental Rating: Enclosure type 1

2.3 Correct use

The WSE24-2 is an opto-electronic through-beam photoelectric sensor (referred to as

"sensor" in the following) for the optical, non-contact detection of objects, animals, and

persons. A sender (WS) and a receiver (WE) are required for operation. If the product is

used for any other purpose or modified in any way, any warranty claim against SICK AG

shall become void.

3 Product description

3.1 Operating elements and status indicators

OPERATING INSTRUCTIONS

6O P E R A T I N G I N S T R U C T I O N S | WS/WE24-2 8008782.1DMA/2022-07-12 | SICK

Subject to change without notice

Table 1: Display and operating elements

WE-2Bx4x

t1+ t2

PNP

NPN

1Yellow LED indicator

2Potentiometer: adjust‐

ment of sensitivity

3Switch: light (L)/dark

(D)

4Switch: NPN/PNP

5Potentiometer: adjust‐

ment of time delay t2

6Potentiometer: adjust‐

ment of time delay t1

7Potentiometer: adjust‐

ment of time stage

WE24-2Xx3x

PNP

NPN

1Yellow LED indicator

2Potentiometer: adjust‐

ment of sensitivity

3Switch: light (L)/dark

(D)

4Switch: NPN/PNP

WE-2Rx4x

t1+ t2

1Yellow LED indicator

2Potentiometer: adjust‐

ment of sensitivity

3Switch: light (L)/dark

(D)

4Potentiometer: adjust‐

ment of time delay t2

5Potentiometer: adjust‐

ment of time delay t1

6Potentiometer: adjust‐

ment of time stage

WE-2Rx3x

1Yellow LED indicator

2Potentiometer: adjust‐

ment of sensitivity

3Switch: light (L)/dark

(D)

4 Mounting

Mount sensors (sender and receiver) using suitable mounting brackets (see the SICK

range of accessories). Align the sender and receiver with each other.

NOTE

Swap the sender and receiver arrangement at every secondthrough-beam photoelec‐

tric sensor and ensure that there is sufficient distance between the through-beam

photoelectric sensors.

Receiver (WE)

Sender (WS)

Receiver (WE)

Figure 1: Arrangement of several through-beam photoelectric sensors

Note the sensor’s maximum permissible tightening torque of 2Nm.

OPERATING INSTRUCTIONS

8008782.1DMA/2022-07-12 | SICK O P E R A T I N G I N S T R U C T I O N S | WS/WE24-2 7

Subject to change without notice

5 Electrical installation

The sensors must be connected in a voltage-free state. The following information must

be observed, depending on the connection type:

– Plug connection: note pin assignment: when the lid is open, the male connector

can be swiveled horizontally and vertically.

– Terminal connection: Note the permissible cable diameter of 5 to 10mm. When

the lid is open, the M16 connector can be swiveled horizontally and vertically.

Unscrew the M16 connector and remove sealing plug. Lead voltage-free supply

cable through and connect sensor in accordance with table 2 and table 5.

Retighten M16 connector with seal so that the IP enclosure rating of the device is

ensured.

Figure 2: Opening the sensor Figure 3: Electrical connection

Only apply voltage/switch on the power supply once all electrical connections have

been established.

Explanation of the connection diagram (Tables 2-8) which are divided up into DC and

AC/DC devices:

Alarm = alarm output (see table 2 and Additional functions)

n. c. = not connected

NC = normally closed

NO = normally open

Q / Q = switching outputs

TE/Test = test input (see table 2 and table 8)

OPERATING INSTRUCTIONS

8O P E R A T I N G I N S T R U C T I O N S | WS/WE24-2 8008782.1DMA/2022-07-12 | SICK

Subject to change without notice

5.1 WS/WE24-2Bxxx, WS/WE24-2Vxxx

UB: 10 . 30VDC, see „Technical data“, page 14

Table 2: DC, WS

WS24-2 D3x3 D2x0 D4x0 D5x0

1+ (L+) + (L+) + (L+) + (L+)

2- (M) - (M) Test Test

3Test - - (M) - (M)

4- - n.c. n.c.

5- Test - n.c.

IN = 4A

1 2 3 4 5

0.14 ... 1.5 mm2

IN = 4A

2 1

Table 3: DC, WE

WE24-2 B3x3 B2x0 B4x0 V5x0

1+ (L+) + (L+) + (L+) + (L+)

2- (M) - (M) n.c. n.c.

3Q/Q- - (M) - (M)

4-Q/QQ/QQ/Q

5- - - Alarm

IN = 4A

1 2 3 4 5

0.14 ... 1.5 mm2

IN = 4A

2 1

OPERATING INSTRUCTIONS

8008782.1DMA/2022-07-12 | SICK O P E R A T I N G I N S T R U C T I O N S | WS/WE24-2 9

Subject to change without notice

Table 4: DC

NPN

PNP

H, PNP: Q/Q (≤ 100mA)

+ (L+)

Q/Q

– (M)

+ (L+)

Q/Q

– (M)

D, PNP: Q/Q (≤ 100mA)

+ (L+)

Q/Q

– (M)

+ (L+)

Q/Q

– (M)

H, NPN: Q/Q (≤ 100mA)

+ (L+)

Q/Q

– (M)

+ (L+)

Q/Q

– (M)

D, NPN: Q/Q (≤ 100mA)

+ (L+)

Q/Q

– (M)

+ (L+)

Q/Q

– (M)

5.2 WS/WE24-2Rxxx

UB 20 V ... 250 V AC/DC, see „Technical data“, page 14

Table 5: AC/DC

WS24-2U2x0 WE24-2R2x0

1L1 / + L1 / +

2N / - N / -

3- Relay

4- Relay

5- Relay

1 2 3 4 5

0.14 ... 1.5 mm2

IN = 4A

1 2 3 4 5

0.14 ... 1.5 mm2

IN = 4A

OPERATING INSTRUCTIONS

10 O P E R A T I N G I N S T R U C T I O N S | WS/WE24-2 8008782.1DMA/2022-07-12 | SICK

Subject to change without notice

Autres manuels pour WS24-2 Series

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels SICK Accessoires

SICK

SICK Bulkscan Manuel utilisateur

SICK

SICK GTE6L Series Manuel utilisateur

SICK

SICK UM18-2 Pro Manuel utilisateur

SICK

SICK KTX Prime KTX-WB91141259ZZZZ Manuel utilisateur

SICK

SICK senSe2 Manuel utilisateur

SICK

SICK NAV350 Manuel utilisateur

SICK

SICK deTec4 Core Guide de l'utilisateur

SICK

SICK WTV4-3 V-optic Manuel utilisateur

SICK

SICK WLD16 Manuel utilisateur

SICK

SICK SIM2000ST Manuel utilisateur

SICK

SICK Flexi Loop Manuel utilisateur

SICK

SICK WTT190LC-B2233A00 Manuel utilisateur

SICK

SICK SureSense HTF18L Manuel utilisateur

SICK

SICK VICOTEC320 Series Manuel utilisateur

SICK

SICK WTF4F Manuel utilisateur

SICK

SICK PowerProx WTT190L-K Series Manuel utilisateur

SICK

SICK WTT190LC-B2233A00 Manuel utilisateur

SICK

SICK TiM8 P Series Manuel utilisateur

SICK

SICK GTB2 Flat Series Manuel utilisateur

SICK

SICK TiM8P Series Manuel utilisateur

SICK

SICK HTE18 Series Manuel utilisateur

SICK

SICK RS25 Series Manuel utilisateur

SICK

SICK GTB2F-X 41 Series Manuel utilisateur

SICK

SICK MLS Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur