SICK GTB2 Flat Series Manuel utilisateur

OPERATING INSTRUCTION

GTB2 Flat

Miniature photoelectric sensors

OPERATING INSTRUCTION

GTB2 Flat

Miniature photoelectric sensors

Described product

G2F

GTB2F

Manufacturer

SICK AG

Erwin-Sick-Str. 1

79183 Waldkirch

Germany

Production location

SICK Product Center Asia Pte. Ltd.

Singapore

www.sick.com.sg

Legal information

This work is protected by copyright. Any rights derived from the copyright shall be

reserved for SICK AG. Reproduction of this document or parts of this document is only

permissible within the limits of the legal determination of Copyright Law. Any modifica‐

tion, abridgment or translation of this document is prohibited without the express writ‐

ten permission of SICK AG.

The trademarks stated in this document are the property of their respective owner.

Original document

This document is an original document of SICK AG.

2006/42/EC

SAFETY

8023328.18HX | SICK

Subject to change without notice 3

Contents

1 General safety notes......................................................................... 5

2 Notes on UL approval........................................................................ 5

3 Intended use...................................................................................... 5

4 Operating and status indicators...................................................... 5

5 Mounting............................................................................................. 6

6 Electrical installation........................................................................ 6

7 Commissioning.................................................................................. 7

8 Troubleshooting................................................................................. 9

9 Disassembly and disposal............................................................... 10

10 Maintenance...................................................................................... 10

11 Technical specifications................................................................... 11

11.1 Dimensional drawing................................................................................ 11

11.2 Light spot diameter................................................................................... 12

CONTENTS

48023328.18HX | SICK

Subject to change without notice

1 General safety notes

■Read the operating instructions before commissioning.

■

Connection, mounting, and configuration may only be performed by trained

specialists.

■

2006/42/EC

SAFETY

Not a safety component in accordance with the EU Machinery Directive.

■

When commissioning, protect the device from moisture, contamination and

UV radiation (sun light).

■These operating instructions contain information required during the life cycle of

the sensor.

2 Notes on UL approval

The device must be supplied by a Class 2 source of supply.

UL Environmental Rating: Enclosure type 1

3 Intended use

The GTB2F is an opto-electronic photoelectric proximity sensor (referred to as “sensor”

in the following) for the optical, non-contact detection of objects, animals, and persons.

If the product is used for any other purpose or modified in any way, any warranty claim

against SICK AG shall become void.

4 Operating and status indicators

Photoelectric proximity sensor with background suppression.

Figure 1: Dimensional drawing

GENERAL SAFETY NOTES 1

8023328.18HX | SICK

Subject to change without notice 5

1LED indicator green: supply voltage active

2LED indicator yellow: status of received light beam

5 Mounting

Mount the sensor using a suitable mounting bracket (see the SICK range of acces‐

sories).

Note the sensor's maximum permissible tightening torque of 0.1 Nm.

Note the preferred direction of the object relative to the sensor, cf. see "Dimensional

drawing", page 11.

6 Electrical installation

The sensors must be connected in a voltage-free state (UV = 0 V). The following informa‐

tion must be observed, depending on the connection type:

– Plug connection: note pin assignment: when the lid is open, the male connector

can be swiveled horizontally and vertically.

– Cable: wire color

Only apply voltage/switch on the voltage supply (UV > 0 V) once all electrical connec‐

tions have been established.

Explanation of the connection diagram (Tables pin assignment):

Q = switching outputs

n. c. = not connected

DC: 10 ... 30 V DC

Table 1: Pin assignment

GXX2F(S)

-X14xx

-X54xx

1BN + (L+) + (L+)

2- - -

3BU - (M) - (M)

4BK Q Q

BK: 0.1 mm2, AWG30

BU+BN: 0.127 mm2, AWG28

5 MOUNTING

68023328.18HX | SICK

Subject to change without notice

Table 2: Switching output

PNP Q

(≤ 50 mA)

+ (L+)

– (M)

+ (L+)

– (M)

(≤ 50 mA)

+ (L+)

– (M)

+ (L+)

– (M)

NPN Q

(≤ 50 mA)

+ (L+)

– (M)

+ (L+)

– (M)

(≤ 50 mA)

+ (L+)

– (M)

+ (L+)

– (M)

7 Commissioning

1Alignment

Align sensor on object. Select the position so that the red emitted light beam hits the cen‐

ter of the object. You must ensure that the optical opening (front screen) of the sensor is

completely clear.

ELECTRICAL INSTALLATION 6

8023328.18HX | SICK

Subject to change without notice 7

Figure 2: Alignment

Figure 3: Alignment 2

2Sensing range

Check the application conditions: Adjust the sensing range and distance to the object or

background and the remission capability of the object according to the corresponding dia‐

gram [see table 3].

Sensing range

Distance in mm (inch)

2 650

Sensing range typ. max.

(0.08)

(0.16)

(0.24)

(0.31)

(0.39)

2320

1Sensing range on white, 90 % remission

2Sensing range on gray, 18 % remission

3Sensing range on black, 6 % remission

Figure 4: Sensing range 8 mm

Sensing range

Sensing range typ. max.

(0.16)

(0.31)

(0.47)

(0.63)

(0.79)

218

1815

1Sensing range in white, 90 % remission

2Sensing ranghe on gray, 18 % remission

3Sensingrange on black, 6 % remission

Distance in mm (inch)

Figure 5: Sensing range 15 mm

7 COMMISSIONING

88023328.18HX | SICK

Subject to change without notice

Sensing range

2 650

Sensing range typ. max.

(0.31)

(0.63)

(0.94)

(1.26)

(1.57)

3528

2320

3529

3530

1Sensing range in white, 90 % remission

2Sensing range on gray, 18 % remission

3Sensing range on black, 6 % remission

Distance in mm (inch)

Figure 6: Sensing range 30 mm

4 5 6

Figure 7: Description of the sensing range areas

Table 3: Sensing range areas

Sens‐

ing

range

object

color

-Xxx4x 6-Xxx1x 6-Xxx3x 6

40 ... 1 mm 0 ... 1 mm 0 ... 1 mm

5 / 11 ... 9 mm 1 ... 18 mm 1 ... 35 mm

5 / 22 ... 9 mm 2 ... 18 mm 2 ... 35 mm

5 / 32 ... 9 mm 2 ... 18 mm 2 ... 35 mm

Use see table 2, page 7 to check the function. If the switching output fails to behave in

accordance with the table, check the application conditions. See section Fault diagnosis.

3Sensing range setting

Sensor which it is not possible to set: The sensor is adjusted and ready for operation.

8 Troubleshooting

The Troubleshooting table indicates measures to be taken if the sensor stops working.

Table 4: Troubleshooting

LED indicator/fault pattern Cause Measures

Yellow LED does not light up

even though the light beam is

aligned to the object and the

object is within the set sensing

range

No voltage or voltage below

the limit values

Check the power supply,

check all electrical connec‐

tions (cables and plug connec‐

tions)

Voltage interruptions Ensure there is a stable power

supply without interruptions

TROUBLESHOOTING 8

8023328.18HX | SICK

Subject to change without notice 9

LED indicator/fault pattern Cause Measures

Sensor is faulty If the power supply is OK,

replace the sensor

Yellow LED lights up, no object

in the path of the beam

The sensing range distance is

too large

Reduce the sensing range,

see Figures 6-8 and table 3

Object is in the path of the

beam, yellow LED does not

light up

Distance between the sensor

and the object is too long or

sensing range is set too short

Increase the sensing range,

see Figures 6-8 and table 3

9 Disassembly and disposal

The sensor must be disposed of according to the applicable country-specific regula‐

tions. Efforts should be made during the disposal process to recycle the constituent

materials (particularly precious metals).

NOTE

Disposal of batteries, electric and electronic devices

•According to international directives, batteries, accumulators and electrical or

electronic devices must not be disposed of in general waste.

•The owner is obliged by law to return this devices at the end of their life to the

respective public collection points.

•

WEEE: This symbol on the product, its package or in this document, indi‐

cates that a product is subject to these regulations.

10 Maintenance

SICK sensors are maintenance-free.

We recommend doing the following regularly:

•Clean the external lens surfaces

•Check the screw connections and plug-in connections

No modifications may be made to devices.

Subject to change without notice. Specified product properties and technical data are

not written guarantees.

9 DISASSEMBLY AND DISPOSAL

10 8023328.18HX | SICK

Subject to change without notice

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels SICK Accessoires

SICK

SICK DL100 Pro Manuel utilisateur

SICK

SICK WTF16 Manuel utilisateur

SICK

SICK RMS1000 Manuel utilisateur

SICK

SICK GRTB18 Manuel utilisateur

SICK

SICK SureSense HSE18 Series Manuel utilisateur

SICK

SICK WL12G-3P3572S12 Manuel utilisateur

SICK

SICK EventCam Manuel

SICK

SICK AR60 Manuel utilisateur

SICK

SICK SIM2000 Manuel utilisateur

SICK

SICK Flexi Loop Manuel utilisateur

SICK

SICK MPB10 Manuel utilisateur

SICK

SICK SIM1004 Manuel utilisateur

SICK

SICK KTS Core KTS-WS41141142ZZZZ Manuel utilisateur

SICK

SICK GLS621 Manuel utilisateur

SICK

SICK WL34 Manuel utilisateur

SICK

SICK LFV 200 Manuel utilisateur

SICK

SICK WL24-2 Series Manuel utilisateur

SICK

SICK LFV 200 Manuel utilisateur

SICK

SICK LiDAR Manuel

SICK

SICK GSE2 Flat Side Manuel utilisateur

SICK

SICK TriSpectorP1000 Manuel utilisateur

SICK

SICK SureSense HTF18L Manuel utilisateur

SICK

SICK WTB4F Manuel utilisateur

SICK

SICK LMS400 Guide de référence

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur