Shyam RF Series Manuel utilisateur

. Page

Next Generation

Signal Enhancement

RF / DB6M Series

5920 003

0 200 September 2010

(Dual Band)

6 Sub-Band Repeater for Outdoor Applications

(FCC ID: S3CDB6M33SA and IC:5751A-DB6M33SA

for AWS and 700 LTE Upper C Sub-Bands only)

PROPRIETARY INFORMATION

The information contained herein is proprietary to Shyam Telecom Limited.

Unauthorized access, copy and replication are prohibited. This document must

not be copied in whole or part by any means or it shall not be disclosed or

divulged to any third Party without the prior written consent of Shyam Telecom

imited

. Page

Next Generation

Signal Enhancement

CONTENTS

1. Document History.........................................................................................4

2. Disclaimer......................................................................................................5

3. Safety Instructions and Warnings...............................................................6

3.1. Personnel Safety....................................................................................6

3.2. Equipment Safety...................................................................................6

3.3. Electrostatic Sensitivity..........................................................................6

4. Introduction...................................................................................................7

4.1. Purpose .................................................................................................7

4.2. Scope.....................................................................................................7

4.3. Definitions..............................................................................................7

4.4. References ............................................................................................8

4.5. General..................................................................................................9

5. Functional Description of DB6M Dual Band Repeater...............................9

5.1. General Description...............................................................................9

6. To Get started-Basic Software Control Of the system.............................11

6.1. General................................................................................................11

6.2. Terminal Set-up ...................................................................................12

6.3. Block Schematic Description ...............................................................26

7. DB6M Repeater Specifications..................................................................28

7.1. Electrical Specifications-RF...................................................................1

7.2. Electrical Specification Power Requirement ..........................................1

7.3. External Electrical Interface.................................................................29

7.4. Mechanical Specification .....................................................................29

7.5. Environmental Specification.................................................................29

7.6 Contents of Delivery............................................................................30

8. Installation...................................................................................................31

8.1. Preparation Sheet- Pre Installation......................................................31

8.2. Engineering Consideration...................................................................32

8.3. Installation Tools..................................................................................34

8.4. Installation Procedure..........................................................................34

8.5. Repeater Gain Settings........................................................................35

8.6. Commissioning ....................................................................................35

8.7. Dos & Don’t Dos..................................................................................36

. Page

Next Generation

Signal Enhancement

8.8. Checklist – Post Installation.................................................................37

9. Trouble Shooting........................................................................................40

10. System Maintenance.................................................................................41

10.1. General..............................................................................................41

10.2. Preventive Maintenance ....................................................................41

11. Shut Down Mechanisms……………………………………………………42

. Page

Next Generation

Signal Enhancement

1. Document History

Document

Number Document

Name Date Compiled

by Approved

by Revision

5920 0030

200 DB6M Dual

Band Repeater September

2010 Inderjit Ramvir

Singh

Revision Revised Section Date

. Page

Next Generation

Signal Enhancement

Intentionally Left Blank

2. Disclaimer

Every attempt has been made to make this material complete, accurate, and

up-to-date. Users are cautioned, however, that Shyam Telecom Limited

reserves the right to make changes without notice and shall not be

responsible for any damages including consequential, caused by reliance of

the contents presented, including, but not limited to, typographical,

arithmetical, or listing errors.

Product name(s) referenced in this document may be trademarks or

registered trademarks of their respective companies, and are hereby

acknowledged.

In areas with unstable power grids (mains) all repeaters must be installed with

a voltage regulator ensuring a constant voltage level at the repeater power

input. A maximum voltage deviation should remain within the input range to

the repeaters for warranty purposes.

All antennas must be installed with lightening protection. Damage to internal

modules, as a result of lightening is not covered by the warranty.

All specifications are subject to change without prior notice.

. Page

Next Generation

Signal Enhancement

3. Safety Instructions and Warnings

3.1. Personnel Safety

Before installing or replacing any equipment, the entire manual should be

read and understood. The user needs to supply the appropriate AC power to

the Repeater. Incorrect AC power settings can damage the repeater and may

cause injury to the user.

Throughout this manual, there are "Caution" warnings, "Caution" calls

attention to a procedure or practice, which, if ignored, may result in injury or

damage to the system or system component or even the user. Do not

perform any procedure preceded by a "Caution" until the described

conditions are fully understood and met.

3.2. Equipment Safety

When installing, replacing or using this product, observe all safety

precautions during handling and operation. Failure to comply with the

following general safety precautions and with specific precautions described

elsewhere in this manual violates the safety standards of the design,

manufacture, and intended use of this product. Shyam Telecom Limited

assumes no liability for the customer's failure to comply with these

precautions. This entire manual should be read and understood before

operating or maintaining the repeater system.

It calls attention to a procedure or practice which, if not followed, may result

in personal injury, damage to the system or damage to individual

components. Do not perform any procedure preceded by a

CAUTION until described conditions are fully understood and met.

3.3. Electrostatic Sensitivity

ESD = ELECTROSTATIC DISCHARGE SENSITIVE DEVICE

Observe electrostatic precautionary procedures.

CAUTION

. Page

Next Generation

Signal Enhancement

Semiconductor transmitters and receivers provide highly reliable performance

when operated in conformity with the intentions of their design. However, a

semiconductor may be damaged by an electrostatic charge inadvertently

imposed by careless handling.

Static electricity can be conducted to the semiconductor chip from the centre

pin of the RF input connector, and through the AC connector pins. When

unpacking and otherwise handling the Repeater, follow ESD precautionary

procedures including the use of grounded wrist straps, grounded workbench

surfaces, and grounded floor mats.

The RFrepeater mentioned is tested thoroughly for maximum composite power.

There is provision of ALC / APC (automatic level control / automatic power

control) which limits the output power in DL path and in UL path beyond the

specified limit. It operates in LTS 700 band – upper C sub-band of 10 MHz BW

(CF in UL 781 MHz & CF in DL 751 MHz) and AWS band 10 MHz sub-band (

UL 1710-1755MHz, DL 2110-2155MHz). Donor antenna and server antenna

must be fixed on permanent structure with enough isolation between donor and

server antenna to avoid any possible oscillations.

4. Introduction

4.1. Purpose

The purpose of this document is to describe the electrical and mechanical

specifications, operation and maintenance of the DB6M Dual Band

Repeater.

4.2. Scope

This document is the product description of the Shyam DB6M Dual Band

Repeater for outdoor application.

4.3. Definitions

AGC Automatic Gain Control

ALC Automatic Level Control

APC Automatic Power Control

BCCH Broadcast Control Channel

BTS Base Transceiver Station

BSEL Band Selective

. Page

Next Generation

Signal Enhancement

CDMA Coded Division Multiple Access

CMC Configuration & Monitoring Console software

CMB Combiner Unit

CSEL Channel Selective

DCS Digital Communication System

DL Downlink signal (from base station via repeater to

mobile station)

EGSM Extended Global System for Mobile Communication

ETSI European Telecommunications Standard Institute

GSM Global System for Mobile communication

GUI Graphics User Interface

LAC Location Area Code of the BTS site

LED Light Emitting Diode

LNA Low Noise Amplifier

LO Local Oscillator

MS Mobile Station

MSC Mobile Switching Center

NMS Network Management System

PCN Personal Communication Network

PCS Personal Communication System

PSU Power Supply Unit

RF Radio Frequency

RMS Repeater Management System/Remote Monitoring

System

RSSI Received Signal Strength Indication

RTC Real Time Clock

SMS Short Message Service

TACS Total Access Communication System

TDMA Time Division Multiple Access

VFD Visual Florescent Display

UL (Uplink) Uplink signal direction (from mobile station via

repeater to base station)

4.4. References

[1] ETS 300 086

Radio Equipment and Systems Land mobile service Technical

characteristics and test conditions for radio equipment with an internal or

external RF connector intended primarily for analogue speech.

[2] ETS 300 609-4

Digital cellular telecommunications system (phase 2): Base Station

. Page

Next Generation

Signal Enhancement

Systems (BSS) equipment specification: Part 4: Repeaters.

[3] ETS 300 342-3

Radio Equipment and Systems (RES); Electro-Magnetic Compatibility

(EMC) for European Digital Cellular Telecommunications Systems. Base

Station Radio and ancillary equipment and Repeaters meeting phase 2

GSM requirements.

4.5. General

Mobile Communications Systems are planned as cellular systems and each

cell of the base station is required to provide RF coverage over a certain

geographical area as per defined RF power levels. Due to the RF

propagation properties, even using high radiated RF powers or complicated

antenna systems, there are zones within the coverage area where the RF

signal strength from base station remains inadequate for establishing the

desired connectivity to mobile users.

Repeaters traditionally are deployed in the Mobile Communication Network

to fill in the “Dead Zones”caused by blocking of signals by geographic

topologies such as mountains, valleys, dense foliage, high rising urban

landscapes and other man-made structures. The distance from the base

station also adversely affects the RF signal strength. The user views

repeaters as a means to extend base station coverage so as to reduce the

number of base stations and thereby accelerate network availability.

Repeater systems are installed after meticulous planning between BTSs and

the mobile users to provide RF coverage in the shadowed regions. Repeater

systems are available for different applications and ultimate choice shall

depend on some of the factors mentioned below:

•Area to be provided with coverage.

•Indoor/outdoor coverage.

•Availability of BTSs in the vicinity.

•Antenna isolation to be achieved.

5. Functional Description of DB6M Dual Band Repeater

5.1. General Description

The DB6M dual band modular Repeater System is designed to provide

outdoor coverage and can handle signals in up to six sub bands maximum

with 3+3 configuration or as per requirement in two of the service bands,

used around the World by various service operators. It provides highly

selective amplification in the pre-set frequency bands. The details of

operating service frequency bands are given below:

SNo Service Band DL Frequency (MHz) UL Frequency (MHz)

. Page

Next Generation

Signal Enhancement

S.No.

Service Band DL Frequency (MHz) UL Frequency (MHz)

1. SMR 800 851-866 806-821

2. Cellular 869-894 824-849

3. SMR 900 935-941 896-902

4. EGSM 925-960 880-915

5. GSM 900 935-960 890-915

6. DCS 1805-1880 1710-1785

7. PCS 1930-1990 1850-1910

8. UMTS 2110-2170 1920-1980

9. AWS 2110 – 2155 1710 - 1755

10. LTE 700 Upper C, A and B sub-bands are available

The Customer is requested to refer to the sticker on the repeater unit giving

the details of frequency bands set &the bandwidths of different sub bands

equipped in the repeater.

**Only sub bands of AWS and LTE700 Upper C are for FCC and IC approval under FCC ID:

S3CDB6M33SA and IC:5751A-DB6M33SA.

Models: OD6R2-Equipped with 2sub bands

OD6R3-Equipped with 3sub bands

OD6R4-Equipped with 4sub bands

OD6R5-Equipped with 5sub bands

OD6R6-Equipped with 6sub bands

•The DB6M repeater is designed to provide optimal coverage, the

area covered shall primarily depend on RF power radiated, manmade

structures in the area (high rise buildings), the geographical topologies

and availability of reflecting surfaces.

•The ultimate performance &coverage shall depend on the

obstructions blocking / absorbing of the RF signals by various objects

between the Server antenna of RF repeater and the mobile users.

•The repeater is specifically designed for the Operators who are

allocated frequency spectrum in different service bands and non-

contiguous sub bands are specified.

•The repeater adopts duplex mode and bi-directional amplification for

UL & DL signals between the base station and mobile users.

Autres manuels pour RF Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Shyam Répétiteur

Shyam

Shyam R-20-93 Fiche technique

Shyam

Shyam RF/DBR Series Manuel utilisateur

Shyam

Shyam RF Series Manuel utilisateur

Shyam

Shyam HB-20 Series Fiche technique

Shyam

Shyam DBR5R Manuel utilisateur

Manuels Répétiteur populaires d'autres marques

Gigaset

Gigaset 108 Manuel utilisateur

Ace TECHNOLOGY

Ace TECHNOLOGY USR-1900A Manuel utilisateur

Kenwood

Kenwood TKR-750-850 Manuel de la liste des pièces

Asus

Asus RP-AC51 Manuel utilisateur

Exibel

Exibel HRP0101 Manuel utilisateur

Kidde

Kidde Vega Manuel utilisateur

Telcosat

Telcosat RBB 850 Guide d'installation

York

York Universal LINC485 Manuel utilisateur

MIKOM

MIKOM MRx01B Power Series Manuel utilisateur

Simrad

Simrad RD 301 Manuel utilisateur

Tait

Tait TB7304 Manuel utilisateur

R-tron

R-tron RSN-CDMA-37-C Manuel utilisateur

Inventronics

Inventronics DALI REPEATER SO Manuel utilisateur

XFP

XFP 16 Manuel utilisateur

Andrew

Andrew MRx18 Manuel utilisateur

COMBA

COMBA RXA3748 Manuel utilisateur

ADRF

ADRF SDR-ICS-43 Manuel utilisateur

Teltonika

Teltonika WRP100 Manuel utilisateur