showhome ZW1502 Manuel utilisateur
FCC/IC
ZW1502 2 Outlet Power Strip
Show Home Products warrants this product to be free from manufacturing defects for
a period of two years from the original date of consumer purchase. This warranty is limited
to the repair or replacement of this product only and does not extend to consequential or
incidental damage to other products that may be used with this product.
This warranty is in lieu of all other warranties, expressed or implied. Some states do not
allow limitations on how long an implied warranty lasts or permit the exclusion or limitation
of incidental or consequential damage, so the above limitations may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from
state to state. if the unit should prove defective within the warranty period.
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES:
EXERCISE EXTREME CAUTION WHEN USING Z-Wave
DEVICES TO CONTROL APPLIANCES. OPERATION
OF THE Z-Wave DEVICE MAY BE IN A DIFFERENT
ROOM THAN THE CONTROLLED APPLIANCE, ALSO AN
UNINTENTIONAL ACTIVATION MAY OCCUR IF THE WRONG
BUTTON ON THE REMOTE IS PRESSED. Z-Wave DEVICES
MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED
EVENT PROGRAMMING. DEPENDING UPON THE APPLI-
ANCE, THESE UNATTENDED OR UNINTENTIONAL OP-
ERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS
CONDITION. FOR THESE REASONS, WE RECOMMEND
DO NOT RETURN THIS PRODUCT TO THE STORE
THE FOLLOWING:
DO NOT USE Z-Wave DEVICES TO CONTROL ELECTRIC
HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRES-
ENT A HAZARDOUS CONDITION DUE TO UNATTENDED OR
UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL.
WARNING
WARRANTY
SPECIFICATIONS
Website www.ishowlights.com
Federal Communications Commission (FCC) Statement
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may caus harmful interference to radio communications.However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.Increase the separation between the equipment and
receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.Consult the dealer or an experienced radio/TV technician for help.This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
IC Caution:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired
operation of the device.
DECLARATION DE CONFORMITE D'INDUSTRIE CANADA
Ce périphérique a été testé et reconnu conforme aux limites spécifiées dans RSS-210.
Son utilisation est soumise aux deux conditions suivantes :
(1) il ne doit pas provoquer d'interférences gênantes et
(2) il doit tolérer les interférences re.ues, notamment cellessusceptibles d'en perturber le fonctionnement.
Model:ZW1502
Power supply: 110V.
Signal (Frequency): 908.42 MHZ.
Outlet: Two grounded outlets
Cord Length: 3ft.
Wireless Controller and the closest Z-Wave
receiver module.
Specifications subject to change without notice
due to continuing product improvement
3.Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
1. Plug the Power Strip into a standard grounding duplex wall receptacle. Ensure that there are noexposed conductors.
2. Make sure electronic equipment is turned off before plugging into the surge protector outlets. Do not use extension cords
to connect equipment to the Power Strip.
3. Move power switch to “ON.” Your stripe unit should be providing surge protection. Check indicator light(s) periodically (see
note). The glowing stripe indicator light shows that stripe protection is being provided.
4. Connected equipment can now be turned on.
5. The association group supports five nodes and life line function
NOTE: Check the blue “Protected” light periodically. A glowing blue indicator light shows that stripe protection is being
provided. If the blue “Protected” indicator light stops glowing, the stripe protective components have expired and will no
longer provide surge protection. In this event, the Connected Equipment Warranty is no longer valid and the stripe
protector should be replaced.
TO return your switch to factory default:
1. If plugged in, unplug the smart switch from the receptacle.
2. Press and hold the top button for at least 3 seconds while you plug the smart switch into a receptacle.
1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.
2. Once the controller is ready to include your device, press up and release the toggle to include it in the network.
3. Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize
performance.
4. The device is associated in the same group when it included in setting process. Now you can control your Z-Wave
device according to groups, scenes, schedules and automation programmed. If your controller features remote
access, you can now control all devices in Z-Wave network from mobile devices.
To exclude and reset the device
1. Follow the instructions for your Z-Wave certified controller to exclude a device from the Z-Wave network.
2. Once the controller is ready to Exclude your device, press up and release the toggle to exclude it from the network.
Our product can be included and operated in Z-Wave network with other certified devices and/or other applications.
All non-battery nodes within Z-Wave network will act as repeaters.
Power Strip — Limited Lifetime W arranty
Show Home Products Company warrants this Power Strip to be free of defects in workmanship and/or materials
for the life of the Power Strip. If such a defect should arise during the life of the Power Strip, Show Home Products
Company will, at its option, either repair or replace the Power Strip without charge. This warranty does not cover damage
caused by lightning, accident, misuse or alterations to the Power Strip.
This Power Strip, like all surge protectors, has a finite lifespan. Even under normal circumstances and in the absence of
defects, the product’s life will expire when the Power Strip’s component capacity has been exceeded,
thereby ceasing to provide protection from strips.
Important safeguards
Guarantee
ADDING TO Z-Wave NETWORK
Plug ZW1502 into a wall outlet, press ZW1502 button (corresponding to the position of the socket), LED indicator light will turn
on, press the button again, LED off, output turn off.
the master controller enters the "Add Mode" , press the button ZW1502, let ZW1502 added into the home center;
Outlet
Power ON/OFF
Key LED
The main controller can control the first and second outlet socket output. When registration is by the home center(open and closed).
Adding device to Z-Wave network:
Autres manuels showhome Multiprise
