Sherwin-Williams NOVAspx 824-012 Manuel utilisateur
OWNER’S
MANUAL
824–015
Rev.
C
Supercedes Rev. B
NOVAspx
ELECTRIC, AIRLESS PAINT SPRAYER
3000
psi (207 bar
, 21 MPa) Maximum Working Pressure
Model 824–012, Series A
Standard
mount; complete sprayer with hose, gun,
RAC IV
DripLess
T
ip Guard and SwitchT
ip
The SHERWIN–WILLIAMS COMPANY, CLEVELAND, OHIO 44115
This
manual contains important
warnings and information.
READ AND RETAIN FOR REFERENCE
06973A
Model 824–012
Table
of Contents
Warnings 2.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component
Identification and Function
5.
. . . . . . . . . . .
Setup 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation
7.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Startup
9.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shutdown
and Care
11.
. . . . . . . . . . . . . . . . . . . . . . . . . .
Flushing 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Test 17.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General
Repair Information
18.
. . . . . . . . . . . . . . . . . . . .
Motor
Brush
19.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displacement
Pump Repair
21.
. . . . . . . . . . . . . . . . . . . .
Motor 22
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor
Start Board
23.
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power
Supply Cord
23.
. . . . . . . . . . . . . . . . . . . . . . . . . . .
ON/OFF
Switch
23.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive
Housing, Connecting Rod, Crankshaft
24.
. . . . .
Pressure
Control
26.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure Transducer 27.
. . . . . . . . . . . . . . . . . . . . . . . . .
Suction
Hose
27.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drain
V
alve 28.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical
Data
29.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model
824–012 Sprayer Parts Drawing
30.
. . . . . . . . .
Model
824–012 Sprayer Parts List
31.
. . . . . . . . . . . . . .
Sherwin-Williams
W
arranty 32.
. . . . . . . . . . . . . . . . . . .
Symbols
Warning Symbol
WARNING
his
symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This
symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
FIRE AND EXPLOSION HAZARD
Improper
grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury
.
If there is any static sparking or you feel an electric shock while using this equipment,
stop spray-
ing immediately
.
Do not use the equipment until you identify and correct the problem.
Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
Keep the spray area free of debris, including solvent, rags, and gasoline.
Electrically disconnect all equipment in the spray area.
Extinguish all open flames or pilot lights in the spray area.
Do not smoke in the spray area.
Do not turn on or of
f any light switch in the spray area while operating or if fumes are present.
Do not operate a gasoline engine in the spray area.
Use only with a grounded outlet that matches the grounded plug of this equipment.
WARNING
INJECTION HAZARD
Spray
from the gun, leaks or ruptured components can inject fluid into your body and cause extremely
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also
cause serious injury
.
Fluid injected into the skin is a serious injury
. The injury may look like just a cut, but it is a serious
injury
. Get immediate medical attention.
Do not point the gun at anyone or at any part of the body
.
Do not put your hand or fingers over the spray tip.
Do not stop or deflect leaks with your hand, body
, glove or rag.
Do not “blow back” fluid; this is not an air spray system.
Always have the tip guard and the trigger guard on the gun when spraying.
Check the gun dif
fuser operation weekly
. Refer to the gun manual.
Be sure the gun trigger safety operates before spraying.
Lock the gun trigger safety when you stop spraying.
Follow the
Pressure Relief Procedure
on page 9 if the spray tip clogs and before cleaning,
checking or servicing the equipment.
T
ighten all fluid connections before operating the equipment.
Check the hoses, tubes, and couplings daily
. Replace worn or damaged parts immediately
. Do not
repair high pressure couplings; you must replace the entire hose.
Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by
kinks or bends near the couplings.
TOXIC FLUID HAZARD
Hazardous
fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container
. Dispose of hazardous fluid according to all local,
state and national guidelines.
Always wear protective eyewear
, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer
.
MOVING
P
ARTS HAZARD
Moving
parts can pinch or amputate your fingers.
Keep clear of all moving parts when starting or operating the pump.
Before servicing the equipment, follow the
Pressure Relief Procedure
on page 9 to prevent the
equipment from starting unexpectedly
.
WARNING
INSTRUCTIONS
EQUIPMENT MISUSE HAZARD
Equipment
misuse can cause the equipment to rupture or malfunction and result in serious injury
.
D
This equipment is for professional use only
.
D
Read all instruction manuals, tags, and labels before operating the equipment.
D
Use the equipment only for its intended purpose. If you are not sure, call your distributor
.
D
Do not alter or modify this equipment. Use only genuine Graco parts.
D
Check equipment daily
. Repair or replace worn or damaged parts immediately
.
D
Do not exceed the maximum working pressure of the lowest rated system component. Refer to the
T
echnical Data
on page 29 for the maximum working pressure of this equipment.
D
Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the
Tech-
nical Data
section of all equipment manuals. Read the fluid and solvent manufacturer
’
s warnings.
D
Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in pressurized aluminum equipment. Such use could result in a
chemical reaction, with the possibility of explosion.
D
Do not use hoses to pull equipment.
D
Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82
_
C (180
_
F) or below –40
_
C (–40
_F).
D
Do not lift pressurized equipment.
D
Comply with all applicable local, state, and national fire, electrical, and safety regulations.
Liquids
can be injected into the body by high pressure airless spray or
leaks
– especially hose leaks.
Keep body clear of the nozzle. Never stop leaks with any part of the
body
. Drain all pressure before removing parts.A
void accidental trigger
-
ing of gun by always setting safety latch when not spraying.
Never spray without a tip guard.
In case of accidental skin injection, seek immediate
“Surgical T
reatment”.
Failure to follow this warning can result in amputation or serious injury
.
FIRE
AND
EXPLOSION HAZARD
SKIN INJECTION
HAZARD
READ AND UNDERSTAND ALL LABELS AND INSTRUCTION MANUALS BEFORE USE
Spray
painting, flushing or cleaning equipment with flammable liquids in
confined
areas can result in fire or explosion.
Use
outdoors or in extremely well ventilated areas. Ground equipment,
hoses,
containers and objects being sprayed.
A
void all ignition sources such as static electricity from plastic drop
cloths,
open flames
such as pilot lights, hot objects such as cigarettes,
arcs
from connecting or disconnecting power cords or turning light
switches on and of
f.
Failure to follow this warning can result in death or serious injury
.
NOTE: This
is an example of the DANGER label on
your sprayer
. This label is available in other
languages, free of charge. See page 29 to order
.
06973A
Component
Identification and Function
C
Fig.
1
G
E
F
D
A
M
B
J
L
Model 824–012 Shown
K
H
N
05963
AMotor
DC motor
, 120 V
ac, 15A, 1 phase
B
Drive Assembly
T
ransfers power from DC motor to the displacement pump
C
Pressure Adjusting Knob
Controls fluid outlet pressure
D
ON/OFF Switch
Power switch that controls 120 V
ac power to sprayer
E
Fluid Outlet
Hose and spray gun is connected here
F
Displacement Pump
Pressurizes fluid to be sprayed through spray gun
G
50 ft (15 m) Main Hose
1/4 in. ID, grounded, nylon hose with spring guards on both ends
H
RAC IV T
ip Guard
Reverse-A-Clean (RAC) ti
p g
uard reduce
s t
he ris
k o
f f
lui
d i
njectio
n i
njury
J
Contractor FTx Gun
High pressure spray gun with gun safety latch
K
RAC IV Switch T
ip
RAC switch tip atomizes fluid and removes clogs from spray tip without
removing tip from spray gun
L
Pressure Drain V
alve
Relieves fluid pressure when open
M
Pressure Control
Controls motor to maintain fluid pressure. W
orks with pressure
adjusting knob.
N
Spray Gun Safety Latch
Inhibits accidental triggering of spray gun
Setup
WARNING
If you supply your own hoses and spray gun, be
sure the hoses are electrically conductive, that the
gun has a tip guard, and that each part is rated for
at least
3000 psi (207 bar
, 21 MPa) Working Pres
-
sure
. This is to reduce the risk of serious injury
caused by static sparking, fluid injection or over-
pressurization and rupture of the hose or gun.
CAUTION
T
o avoid damaging the pressure control, which may
result in poor equipment performance and compo
-
nent damage, follow these precautions:
1.
Always use a nylon spray hose at least 50 ft. (15
m) long.
2.
Never use a wire braid hose as it is too rigid to
act as a pulsation dampener
.
3.
Never install any shutof
f device between the filter
and the hose.
See Fig. 2.
1. Connect the hose (74) and gun (67)
and screw it
onto the outlet nipple (28). Don’t use thread
sealant, and don’t install the spray tip yet!
2. Fill the wet–cup (102).
Pry of
f the wet-cup seal.
Fill the cup 1/3 full with Graco Throat Seal Liquid
(TSL), supplied. Install the wet-cup seal.
3.
Plug in the sprayer
.
Be sure the ON/OFF switch
(52) is OFF
. Plug the cord into a 15A grounded
outlet at least 20 feet away from the spray area. A
12 A
WG 150 ft (45 m) grounded extension cord
may be used.
WARNING
FIRE AND EXPLOSION HAZARD
Proper electrical grounding is essential
to reduce the risk of fire or explosion
which can result in serious injury and
property damage. Also read
FIRE OR
EXPLOSION HAZARD
on page 2
4. Flush the pump
to remove the lightweight oil
which was left in to protect pump parts after fac
-
tory testing. See page 12.
5.
Prepare the paint
according
to the manufacturer
’s
recommendations. Remove any paint skin. Strain
the paint through a fine nylon mesh bag (available
at most paint dealers) to remove particles that
could clog the spray tip. This is an important step
toward trouble-free paint spraying.
06973A
Fig. 2
1
3
4
2
1/4
npsm(m) fluid outlet
Rotate clockwise to increase pressure
Do not install any shutof
f device here
Fill 1/3 full with TSL
Shown in closed or spray position
5
32
33
64
28
74
102
52
12
3
4
5
67 Model
824–012 Shown
Setup
Grounding
WARNING
Improper installation or alteration of the grounding
plug will result in a risk of electric shock, fire or
explosion that could cause serious injury or death.
1.
This equipment requires a 120 V
ac, 60 Hz, 15A
circuit with a grounding receptacle. See Fig. 3.
Fig. 3
Grounding
Prong
Grounded
Outlets
2. Do
not alter the ground prong or use an adapter
.
3.
A 12 A
WG gauge, 50 ft extension cord may be
used with this equipment.
Operation
How to use the gun trigger safety
When
engaged, the gun safety latch prevents the gun
from accidental triggering. See Fig. 4.
WARNING
INJECTION HAZARD
If the gun still sprays when the gun
trigger safety is locked, repair the gun.
See manual 308–645, supplied.
Fig. 4
1
2
Gun
safety latch
shown engaged
2
Gun safety latch
shown disengaged
05964
1
How to use the pressure drain valve.
Use
the pressure drain valve to relieve fluid pressure
from the pump and to help prime the pump. If the valve
senses an over pressure condition, it opens automati
-
cally to relieve fluid pressure. If this happens, stop
spraying immediately, shut of
f and unplug the sprayer
.
Determine the cause of the problem and correct it
before operating the sprayer again. Refer also to the
Troubleshooting
, page 13. See Fig. 5.
7105A
Fig. 5
Closed,
or spray position
Open or drain, position
1
2
1
2
How to use the pressure control.
The
pressure control controls the motor operation so
the sprayer maintains constant fluid pressure at the
pump outlet. T
urn the pressure control knob fully
counterclockwise to obtain the minimum setting. T
urn
the knob clockwise to increase pressure. See Fig. 6.
7105A
Fig. 6
Operation
How to use the RAC IV tip guard.
WARNING
INJECTION
HAZARD
T
o reduce the risk of serious injury
,
whenever you are instructed to relieve
pressure, follow the
Pressure Relief
Procedure
on page 9.
The tip guard alerts you to the risk and helps prevent
placing any part of the body close to the spray tip. The
tip guard also adjusts the vertical or horizontal spray
pattern. See Fig. 9. The tip guard holds a reversing
spray tip. The tip is in the spraying position when the
tip handle points forward. See Fig. 7.
Clean the front of the tip frequently during the day’
s
operation. First, follow the
Pressure Relief Procedure
on page 9.
Fig. 7
Tip
handle shown in
spraying position.
T
urn handle 180
,
trigger gun to clear clog
1
2
2
1
04647
How to remove a tip clog.
1. Release
the gun trigger
. Lock the safety latch.
Rotate the RAC IV tip handle 180
. See Fig. 7.
2.
Unlock the safety latch. T
rigger the gun into a pail
or onto the ground to remove the clog.
3.
Lock the safety latch. Rotate the tip handle to the
spraying position.
4.
If the tip is still clogged, lock the safety latch, shut
of
f and unplug the sprayer
, and open the pressure
drain valve to relieve pressure. Clean the spray tip
as shown in manual 307–848, supplied.
Startup
WARNING
INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally
. Fluid
under high pressure can be injected through the
skin and cause serious injury
. T
o reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the
Pressure Relief Procedure
whenever you:
are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray tip.
Pressure Relief Procedure
1.
Engage the gun safety latch.
2.
T
urn the ON/OFF switch to OFF
.
3.
Unplug the power supply cord.
4.
Disengage the gun safety latch. Hold a metal part
of the gun firmly to a grounded metal pail. T
rigger
the gun to relieve pressure.
5.
Engage the gun safety latch.
6. Open the pressure drain valve. Leave the pressure
drain valve open until you are ready to spray
again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above
, VER
Y SLOWL
Y loos
-
en the tip guard retaining nut or hose end coupling to
relieve pressure gradually
, then loosen completely
.
Now clear the tip or hose obstruction.
Startup Procedure
Use
this procedure each time you start the sprayer to
help ensure the sprayer is ready to operate and that
you start it safely
.
NOTE:
If this is a first-time startup, flush the sprayer
.
See page 12.
NOTE:
Refer to Fig. 2 and the other figures referenced
in the text as you start the sprayer
.
1.
Open the pressure drain valve (42).
See Fig. 8.
2. Don’t install the spray tip until the pump is
primed!
3. Put the suction hose (32) into the paint
. If you
are pumping from a pail, push the drain hose (33)
down below the top of the pail to avoid splashing
paint when the drain valve is opened.
01021A
Open
or drain, position
Fig.
8
1
1
42
4. T
urn the pressure knob (64) to the minimum
setting.
5. Disengage the gun trigger safety
.
See Fig. 4,
page 7.
CAUTION
Do not run the sprayer dry for more than 30 seconds
to avoid damaging the pump packings.
6. T
o prime the pump,
turn the sprayer switch (52)
on.
Slowly increase the pressure until the sprayer
starts. When fluid comes from the pressure drain
valve, close the valve.
Startup
WARNING
FIRE AND EXPLOSION HAZARD
T
o reduce the risk of static sparking and
splashing when priming or flushing the
system, hold a metal part of the gun
firmly to the side of a grounded metal pail before
triggering the gun.
7. T
o prime the hose
, lower the pressure to reduce
splashing. Hold a metal part of the gun firmly
against and aimed into a grounded metal pail.
See
the preceding W
ARNING. Hold the gun trigger
open and slowly increase the pressure until the
pump starts. Keep the gun triggered until all air is
forced out of the system and the fluid flows freely
from the gun. Release the trigger and engage the
gun safety latch.
8. Check all fluid connections for leaks
. Relieve
pressure before tightening the connections.
9.
Engage the gun safety latch.
10. Install the spray tip and tip guard.
Install the
spray tip. If you are using the RAC IV tip guard,
refer to manual 307–848 for installation instruc
-
tions.
11. Adjust the spray pattern
a.
Increase the pressure until spray from the gun
is completely atomized. T
o avoid excessive
overspray and fogging, and to extend tip and
sprayer life, always use the lowest pressure
needed to get the desired results.
b.
If more coverage is needed, use a larger tip
rather than increasing the pressure.
c.
Adjust the direction of the spray pattern. See
Fig. 9. Engage the gun safety latch. Loosen
the retaining nut (A). Position the tip guard for
a horizontal or vertical pattern. Hold the tip
guard in place and tighten the retaining nut.
NOTE:
Spray patterns will change as tips wear
.
Change the spray tip if adjusting the pressure will not
improve the spray pattern.
Fig. 9
For
a horizontal
spray pattern
For a vertical
spray pattern
1
2
2
A
05971
1
Table des matières
Autres manuels Sherwin-Williams Pistolet à peinture
Sherwin-Williams
Sherwin-Williams ULTIMATE Plus+ 1000 Manuel utilisateur
Sherwin-Williams
Sherwin-Williams ULTIMATE 824-030 Manuel utilisateur
Sherwin-Williams
Sherwin-Williams PT2500 Manuel utilisateur
Sherwin-Williams
Sherwin-Williams SUPERNOVA 820-002 Manuel utilisateur
Sherwin-Williams
Sherwin-Williams ProComp 3800 Manuel utilisateur
Sherwin-Williams
Sherwin-Williams 820-169 Series B Manuel utilisateur
Sherwin-Williams
Sherwin-Williams 820169 D Series Manuel utilisateur
Sherwin-Williams
Sherwin-Williams ULTIMATE NOVA 1000 Manuel utilisateur
Sherwin-Williams
Sherwin-Williams 820-001 Manuel utilisateur
Sherwin-Williams
Sherwin-Williams 820-206 Manuel utilisateur
