Sharp AL-1000 Series Manuel utilisateur

WARNING:

FCC Regulations state that any unauthorized changes or modifications to this

equipment not expressly approved by the manufacturer could void the user’s

authority to operate this equipment.

Note:

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of

the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

●

♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠

♠

♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠

♠

♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠

♠

♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠

♠

LISTED ACCESSORY

9K11 ITE.

For use

AL-1000

AL-1010

AL-1020

AL-1200

AL-1220

AL-1280

AL-1520

AL-1040

AL-1240”

“

CONTENTS

1GETTING STARTED

INTRODUCTION 2

– Making floppy disks from CD-ROM 3

MAIN FEATURES 3

– Before reading the next section 3

INSTALLING THE OPTIONAL PRINTER UPGRADE KIT 4

– Checking packed components and accessories 4

– Removing the cabinet cover and board cover 5

– Installing the printer board 6

– Installing the memory 7

– Replacing the cabinet cover and board cover 7

– Connecting the power cord 9

CONNECTING THE INTERFACE CABLE 9

INSTALLING THE PRINTER DRIVER SOFTWARE 10

– Description of the printer driver 10

– Checking the hardware and software requirements 10

– Installing the printer driver 10

– AL-1000 Series printer driver group 16

2PRINTING

PRINTING A PAGE 17

– Executing printing 17

– Indicators on the operation panel 18

SETTING PRINT CONDITIONS FROM PRINTER DRIVER 18

PRINTING FROMAN MS-DOS APPLICATION 21

– Print setting from the MS-DOS prompt 21

– Settings on the front panel 22

– Software printer setting 22

3PRINTER TROUBLE

TROUBLESHOOTING 23

– Printing problems 23

STATUS MONITOR 26

USING OTHER INSTALLED DRIVERS 28

UNINSTALLING PRINTER DRIVER 29

4APPENDIX

SPECIFICATIONS 30

PARALLEL INTERFACE 31

PRINTAREA 32

INDEX

Getting started

GETTING STARTED

This chapter provides basic information for using the SHARP AL-1000 series printer and its

features.

INTRODUCTION

The AL-1000 series machines can be used as a copier and a laser printer. This manual

describes only the printer features of the machine. To use an AL-1000 series machine as a

copier and to learn additional information which relates to both the copier and printer features,

seethecopiermanual.To get full use ofall printer features, familiarizeyourself with thismanual.

For quick reference during printer use, keep this manual in a handy location.

Conventions used in this manual

Inthis manual, thefollowing icons areused to providetheuser with informationpertinent to the

use of the machine.

Warns the user that injury to the user or damage to the machine may result if

the contents of the warning are not properly followed.

Cautions the user that damage to the machine or one of its components may

result if the contents of the caution are not properly followed.

Notes provide information relevant to the machine regarding specifications,

functions, performance, operation and such, that may be useful to the user.

●When you try to execute printing while copying is being performed, printing

will be executed after copying is finished.

●When you try to make a copy while printing is being performed, printing will

beinterruptedand you can makeacopy.Printing will be resumedaftercopying

is finished.

Trademark acknowledgments

Windows, MS-DOS, Windows NT and Windows Printing System are trademarks of Microsoft

Corporation in the U.S.A. and other countries.

IBM, PC/AT and OS/2 are trademarks of International Business Machines Corporation.

HP, LaserJet and PCL are trademarks of the Hewlett-Packard Company.

All other trademarks and copyrights are the property of their respective owners.

Getting started

INTRODUCTION

Making floppy disks from CD-ROM

The printer driver data in the CD-ROM can be copied to floppy disks.

Windows 95/Windows 98/Windows NT 4.0:

Double-click My Computer, Sharp_al, and Makedisk.

Double-click Makedisk.exe.

Follow the on-screen instructions.

Windows 3.1x:

Double-click the File Manager in the Main window of Program Manager and select

CD-ROM and the Makedisk directory.

Double-click Makedisk.exe.

Follow the on-screen instructions.

MAIN FEATURES

qPrinting from Windows 3.1x, Windows 95, Windows 98, and Windows

NT 4.0 applications

●High-speed and high-quality printing can be performed from Windows 3.1x, Windows

95, Windows 98, and Windows NT 4.0 applications through the SHARP GDI (Graphics

Device Interface) system.

●Since print data is processed in the computer, waiting time during printing is short.

wHigh-speed printing at 8 pages/min.

●First print time is approximately 9.6 seconds.

●Print speed is 8 pages/min., when printing multiple pages.

Before reading the next section

TheAL-1000 series copiers are equipped with the printer interface either as standard features

oroptionalfeatures depending on themodel. Ifyour copieris equipped withthe printerinterface

as standard, proceed to page 9 – CONNECTING THE INTERFACE CABLE.

Getting started

INSTALLING THE OPTIONAL PRINTER

UPGRADE KIT

To install the printer board and memory, be sure to follow the precautions below.

Be sure to turn off this machine and your computer and remove the power cord

before starting installation. If not, an electric shock or injury may result.

●Do not touch the chips, circuits, and connectors on the printer board and

memory board directly with your hands. Doing so may damage them through

static electricity.

●Discharge the static electricity in your body by touching a grounded

metal part before starting installation.

●To protect the printer board and memory from static damage, remove them

from protective bags just before starting work.

●Do not touch any object which easily generates static electricity (such as a

computer display) with your hand.

●Do not subject the printer board and memory to undue shock.

●Do not put the printer board or memory in a location which easily

generates static electricity (such as on a carpet).

Checking packed components and accessories

Open the carton and check if the following components and accessories are included.

Interface cable ... 1

(for IBM PC/AT or compatible computers)

Printer board ... 1 Memory ... 1* Printer driver

(CD-ROM) ... 1 Screwdriver ... 1

Screws ...4 Operation manual ...1

* In some models, the memory has been already installed in the machine and is not supplied

in the printer upgrade kit (AL-10PK).

If anything is damaged or not included, contact your SHARP Service Center.

Getting started

INSTALLING THE OPTIONAL PRINTER UPGRADE KIT

Removing the cabinet cover and board cover

Ensure that the power switch on the copier is in the off position. Remove the power

cord from the power cord socket at the rear of the copier.

Remove the screw from the cabinet cover at the rear side of the machine using the

supplied screwdriver.

Slide the cabinet cover in the direction indicated by the arrow and pull the cover while

raising it a little to remove it.

Remove the three screws from the board cover.

Getting started

INSTALLING THE OPTIONAL PRINTER UPGRADE KIT

Open the board cover in the direction indicated by the arrow and then remove it.

Installing the printer board

Before installing the printer board, be sure to read the precautions on page 4.

Remove the printer board from the protective bag.

Install the printer board so that the parallel interface connector of the board is fitted

into the hole for the connector.

Hole for the connector

Secure the printer board using the supplied four screws.

Getting started

INSTALLING THE OPTIONAL PRINTER UPGRADE KIT

Connect the board cable to the connector of the machine.

Installing the memory

If the memory is not supplied in the printer upgrade kit (AL-10PK), proceed to the “Replacing

the cabinet cover and board cover” subsection.

Before installing the memory, be sure to read the precautions on page 4.

Remove the memory from the protective bag.

Check the orientation of the connector on the memory board and the connector on

the machine, and connect them securely.

Replacing the cabinet cover and board cover

Reattach the board cover in the direction indicated by the arrow.

Getting started

Secure the board cover using the three screws which had been removed.

Remove the cabinet cover at the slit portion by bending it back with your hand to

separate it.

Take care in handling the cabinet cover because the exposed edge could be

sharp and may injure your hands.

Fit the projections of the cabinet to the notches of the machine, push the cabinet

downward a little and then slide it in the direction indicated by the arrow.

Secure the cabinet cover using the screw which has been removed.

INSTALLING THE OPTIONAL PRINTER UPGRADE KIT

Getting started

INSTALLING THE OPTIONAL PRINTER UPGRADE KIT

Connecting the power cord

Ensure that the power switch of the copier is in the OFF position. Insert the removed

power cord into the power cord socket at the rear of the copier.

CONNECTING THE INTERFACE CABLE

To use an AL-1000 series machine as a laser printer, connect it to the parallel interface cable.

●Use the supplied parallel interface cable.

●For specifications of the parallel interface, see page 31.

Check that the power switches of both the printer and the computer are in the OFF

position.

Plug the parallel interface cable into the printer interface connector. Fasten the two

bail clips at the side of the printer connector to hold the interface connector in place.

Plug the other end of the cable into the parallel interface connector on your computer.

(Refer to your computer manual for details.)

Bail clip

Interface connector

Parallel interface connector

Cable

The printer sends and receives data bi-directionally and at high speed. Some

switch boxes and pass-through devices cannot support high-speed, bi-

directional transfer of data, and using them may cause printing errors.

Autres manuels pour AL-1000 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sharp Imprimante

Sharp

Sharp AR-M280U Imager Manuel utilisateur

Sharp

Sharp AR-C360P Guide de configuration

Sharp

Sharp DX-C200P Operation Guide de démarrage rapide

Sharp

Sharp BP-50M26 Manuel utilisateur

Sharp

Sharp JX-9600 Manuel utilisateur

Sharp

Sharp JX-720 Manuel utilisateur

Sharp

Sharp AR-MS1 Manuel utilisateur

Sharp

Sharp JX-9500 Manuel utilisateur

Sharp

Sharp AJ-1100 Guide de configuration

Sharp

Sharp MX-C400P Manuel utilisateur

Sharp

Sharp AM-300 Manuel utilisateur

Sharp

Sharp DX-B352P Manuel utilisateur

Sharp

Sharp MX-B380P Manuel d'installation et d'exploitation

Sharp

Sharp AL-1340 - B/W Laser - Copier Manuel utilisateur

Sharp

Sharp CE-129P Manuel utilisateur

Sharp

Sharp JX-735 Manuel utilisateur

Sharp

Sharp MX-2300G Manuel utilisateur

Sharp

Sharp AR-C200P - Color Laser Printer Manuel utilisateur

Sharp

Sharp DX-B350P Manuel utilisateur

Sharp

Sharp AR-M355 Manuel utilisateur

Sharp

Sharp CE-515P Manuel utilisateur

Sharp

Sharp Laser Printer Manuel utilisateur

Sharp

Sharp AR-C260P Manuel utilisateur

Sharp

Sharp MZ-80P3 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur