Sharp DM-1505 - B/W Laser Printer Manuel utilisateur

CODE: 00ZDM1505/A1E

DIGITAL COPIER

DM-1500

MODEL DM-1505

[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[ 3 ] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . 3 - 1

[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . 4 - 1

[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . 5 - 1

[ 6 ] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . 6 - 1

[ 7 ] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . 7 - 1

[ 8 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

[ 9 ] SIMULATION TROUBLE CODES . . . . . . . . . . . . . . 9 - 1

[10] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . 10 - 1

[11] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . 11 - 1

[12] CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . 12 - 1

CONTENTS

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with specified

ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

(DM-1505)

DM-1505

CAUTION

This product is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH stand-

ard and IEC825. This means that this machine does not produce hazardous laser radiation. The use of

controls, adjustments or performance of procedures other than those specified herein may result in haz-

ardous radiation exposure.

This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved

on the eye’s retina, there is the danger of spot damage to the retina.

The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time

of servicing.

1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as

a unit, not as individual parts.

2) Do not look into the machine with the main switch turned on after removing the developer unit, toner

cartridge, and drum cartridge.

3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected

when removing and installing the optical system.

4) The middle frame contains the safety interlock switch.

Do not defeat the safety interlock by inserting wedges or other items into the switch slot.

LASER WAVE –LENGTH : 780 ∼795

Pulse times : 0.481 ms/6 mm

Out put power : 0.20 ±0.03 mW

CAUTION

INVISIBLE LASER RADIATION,

WHEN OPEN AND INTERLOCKS DEFEATED.

AVOID EXPOSURE TO BEAM.

VORSICHT

UNSICHTBARE LASERSTRAHLUNG,

WENN ABDECKUNG GEÖFFNET UND

SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT.

NICHT DEM STRAHL AUSSETZEN.

VARO !

AVATTAESSA JA SUOJALUKITUS

OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ

KATSO SÄTEESEEN.

ADVARSEL

USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR

SIKKERHEDSBRYDERE ER UDE AF

FUNKTION. UNDGÅUDSAETTELSE FOR

STRÅLNING.

VARNING !

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN. –STRÅLEN ÄR FARLIG.

DM-1505

manuals4you.com

At the production line, the output power

of the scanner unit is adjusted to 0.57

MILLI-WATT PLUS 20 PCTS and is

maintained constant by the operation of

the Automatic Power Control (APC).

Even if the APC circuit fails in operation

for some reason, the maximum output

power will only be 15 MILLI-WATT 0.1

MICRO-SEC. Giving and accessible

emission level of 42 MICRO-WATT

which is still-less than the limit of

CLASS-1 laser product.

The foregoing is applicable only to the 220V

model

230V model and 240V model.

VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA

KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA

TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN

TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT

SÄTT ÄN I DENNA BRUKSANVISNING

SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS

FÖR OSYNLIG LASERSTRÅLNING, SOM

ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.

Caution

This product contains a low power laser

device. To ensure continued safety do not

remove any cover or attempt to gain access

to the inside of the product. Refer all

servicing to qualified personnel.

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

DM-1505

[1] GENERAL

1. Major functions

Item

CPM SB/MB 2 Tray SPF R-SPF FAX GDI

with USB

GDI

without

USB

PCL

with USB SOPM Duplex

Model

DM-1500 15CPM MB

DM-1505 15CPM MB

Descriptions of items

CPM: Copy speed (Copies Per Minute)

SB/MB: SB = Manual feed single bypass, MB = Manual feed multi bypass

2 tray: Second cassette unit.

SPF: Original feed unit

R-SPF: Duplex original feed unit

FAX: FAX function.

GDI with USB: GDI printer function with USB.

GDI without USB: GDI printer function without USB.

PCL with USB: PCL printer function with USB.

SOPM: Scan One Print Many function (Many copies are made by one scan.)

Duplex: Auto duplex copy function

Descriptions of table

:Standard provision

:No function or no option available

2. System Configuration

(DM-1500)

(DM-1505)

DM-1505

1 – 1

manuals4you.com

[2] SPECIFICATIONS

1. Basic specifications of copier

A. Basic specifications

Item Spec.

Type Desktop

Copy system Dry, electrostatic

Segment (class) Digital personal copier

External dimensions (W ×D ×H) (mm) DM-1500/DM-1505: 518mm ×482.6mm ×464mm

Weight DM-1500: Approx. 25Kg, (drum cartridges included)

DM-1505: Approx. 26Kg, (drum cartridges included)

B. Operation specification

Section Item Details Spec.

Paper

feed

section

Paper feed

system

DM-1500/DM-1505: 2 tray (250 sheets) + multi bypass (50

sheets)

AB system

Tray paper feed

section

Paper size A4, B5, A5 (Landscape)

Paper weight 56 – 80g/m2

Paper feed capacity 250 sheets

Kinds Standard paper, specified paper, recycled paper

Remark User adjustment of paper guide available

Multi bypass paper

feed section

Paper size A4, B5, A5, B6, A6 (Landscape)

Paper weight 52 – 128g/m2

Paper feed capacity 50 sheets

Kinds ∗1Standard paper, specified paper, recycled paper, OHP, Label,

Postal card

Remark User adjustment of paper guide available

Inch system

Tray paper feed

section

Paper size 8-1/2″×14″, 8-1/2″×11″, 8-1/2″×5-1/2″(Landscape)

Paper weight 15 – 21 lbs.

Paper feed capacity 250 sheets

Kinds Standard paper, specified paper, recycled paper

Remark User adjustment of paper guide available

Multi bypass paper

feed section

Paper size 8-1/2″×14″, 8-1/2″×11″, 8-1/2″×5-1/2″, 3-1/2″×5-1/2″

(Landscape)

Paper weight 14 – 34.5 lbs.

Paper feed capacity 50 sheets

Kinds ∗1Standard paper, specified paper, recycled paper, OHP, Label,

Postal card

Remark User adjustment of paper guide available

Paper for

Duplex

AB system

Paper size A4, B5, A5 (Landscape)

Paper weight 56 – 80 g/m2

Kinds

Standard paper,

Specified paper,

Recycled paper

Inch system

Paper size 8-1/2″×14″, 8-1/2″×11″, 8-1/2″×5-1/2″(Landscape)

Paper weight 15-21 lbs.

Kinds

Standard paper,

Specified paper,

Recycled paper

∗1: OHP, Label, Postal card: each 1 pc.

DM-1505

2 – 1

Section Item Details Spec.

Paper exit section

Exit way Face down

Capacity of output

tray 100 sheets

Originals

Original set Center Registration (left edge)

Max. original size B4 (10″×14″)

Original kinds sheet

Original size

detection None

Optical

section

Scanning

section

Scanning system CCD sensor scanning by lighting lamp scanner

CCD sensor Resolution 400 dpi

Lighting lamp

Type Xenon lamp

Voltage 1.5kV

Power consumption 11 ±3W

Gradation 256 gradations/8bit

Writing

section

Writing system Writing to OPC drum by the semiconductor laser

Laser unit Resolution 600 dpi

Image forming

Photoconductor Type OPC (30φ)

Life 18k

Charger

Charging system Saw -tooth charging with a grid

Transfer system (+) DC corotron system

Separation system (–) DC corotron system

Developing Developing system Dry, 2-component magnetic brush development system

Cleaning Cleaning system Counter blade system (Counter to rotation)

Fusing section

Fusing system Heat roller system

Upper heat roller Type Teflon roller

Lower heat roller Type Silicon rubber roller

Heater lamp

Type Halogen lamp

Voltage 100V/120V/230V

Power consumption 800W

Electrical section

Power source Voltage Local AC voltage

Frequency Common use for 50 and 60Hz

Power consumption

Max. DM-1500/DM-1505: 1000W

Average (during copying) *1) DM-1500/DM-1505: 310Wh/H

Average (stand-by) *1) DM-1500/DM-1505: 70Wh/H

Pre-heat mode *1) DM-1500/DM-1505: 40Wh/H

Auto power shut-off mode *1) DM-1500/DM-1505: 20Wh/H

*1) May fluctuate due to environmental conditions and the input voltage.

C. Copy performance

Section Item Details Spec.

Copy magnification Fixed magnification ratios 3R + 2E (AB system: 50, 70, 81, 100, 141, 200%)

(Inch system: 50, 64, 78, 100, 129, 200%)

Zooming magnification ratios 50 ∼200% (151 steps in 1% increments)

Exposure mode Auto/Manual/Photo

Manual steps (manual,

photo) 5 steps

DM-1505

2 – 2

manuals4you.com

Section Item Details Spec.

Copy speed First copy time

Tray paper feed 9.6 sec. or below (A4) (Pre-heat mode: 16 sec. or

below / Auto power-shut-off mode: 23 sec. or above)

Manual paper feed 10.0 sec (Pre-heat mode: 16 sec. or below / Auto

power-shut-off mode: 23 sec. or above)

AB system:

A4 (Landscape) Copy speed (CPM)

Same size 15

Enlargement 15

Reduction 15

AB system:

B5 (Landscape) Copy speed (CPM)

Same size 15

Enlargement 15

Reduction 15

Inch system:

8-1/2″×14″

(Landscape)

Copy speed (CPM)

Same size 12

Enlargement 12

Reduction 12

Inch system:

8-1/2″×11″

(Landscape)

Copy speed (CPM)

Same size 15

Enlargement 15

Reduction 15

Max. continuous copy

quantity 99

Void

Void area

Leading edge 1 ∼4mm

Trailing edge 4mm or less, 6mm or less

(Duplex copying/both images)

Side edge void area machine with side edge void 0.5mm ∼4.5mm (Total

of both edge voids)

Image loss

OC mode Leading edge Same size: 3.0mm or less / Enlarge (200%): 1.5mm

or less / Reduction (50%): 6.0mm or less

SPF/R-SPF/

Duplex Leading edge Same size: 4.0mm or less / Enlarge (200%): 3.0mm

or less / Reduction (50%): 8.0mm or less

Warm-up time 0 sec.

Power save mode reset time 0 sec.

Paper jam recovery time 0 sec.

D. Printer specifications

Item Contents

Print speed 15 PPM

First print 9.6 sec

Resolution 600 dpi, 300 dpi

Toner save No

Duplex print Yes (for duplex capable copier)

Paper feed tray Multi bypass tray

Tray 1, Tray 2

Paper size

Multi bypass

tray

A4R, B5R, A5R, 8.5" ×

14", 8.5" ×11"R, 8.5" ×

5.5"R, 8.5" ×13", 8.5" ×

12.4"R, DL, C5, COM10,

Monarch

Tray 1 ∼2

A4R, B5R, A5R, 8.5" ×

14"R, 8.5" ×11"R, 8.5" ×

5.5"R, 8.5" ×13"R, 8.5"

×12.4"R

Page description

language

(standard)

PCL6 (PCL XL) emulation

PCL5e emulation

Dot emulation None

Page protection Yes

Item Contents

Interface

(Standard)

IEEE1284 port ×1

USB port ×1

Applicable

Interface Cable

Parallel cable compliant IEEE1284 and less

than 2.0m (Shield and earth equipped)

USB cable less than 2.0 m

Auto Interface

Switching No

Auto Emulation

Switching Yes

Plug and Play Yes

Printer Driver(*)

PCL6

(PCL XL) PCL5e

MS Windows3.1 No Yes

MS Windows95 Yes Yes

MS Windows98 Yes Yes

MS Windows

NT4.0 Yes Yes

Resident Font 45 outline fonts compatible to PCL6

Screen Font 45 outline fonts compatible to PCL6

DM-1505

2 –3

Item Contents

Memory Standard Maximum

8MB 72MB

Expansion Slot for

Memory One DIMM slots

Expansion Memory 64MB, 32MB, 16MB

(commercially-available DIMM:EDO)

Operation Panel

Switches 1 (Online/Offline)

Lamps 2 (DATA, ONLINE)

Display None

Applicable PC IBM PC-AT Compatibles

*: Only Win 98 can be used for USB users.

Operations when both of USB/parallel ports are connected at the same time.

The USB port has a priority over the parallel port.

Smartsharing is invalid.

Interface connected previously Interface connected later Operation

USB (Unfinished print job YES/NO) Parallel port USB: Enable

Parallel port: Disable

Parallel port (Unfinished print job

YES/NO) USB

When USB is connected after 30sec of no communication through the

parallel port, the mode is shifted to the USB mode instantaneously.

If no communication state does not reach 30sec yet, shifting to the USB

mode is retained until 30sec passes. During that time, print jobs are

performed through the parallel port.

Parallel port (Unfinished print job

YES/NO) USB

After completion of unfinished print jobs, if there is no communication for

30sec, shifting to the USB mode is made.

Within 30sec, print jobs are performed through the parallel port.

DM-1505

2 –4

manuals4you.com

[3] CONSUMABLE PARTS

1. Supply system table

A. USA, CANADA

No. Name Content Life Product name Package Remark

1 Developer cartridge

(Black)

Toner/developer cartridge

(Toner: 220g, Developer: 190g)

×1 6K DM-150TD 5 Life setup is based on

A4 5% documents.

For 6% coverage, 5K

life.

IC chip ×1

Warranty Card ×1

Postcard label ×1

Returned Operation Manual ×1

Polyethene bag ×1

2 Drum cartridge Drum cartridge ×1 18K DM-150DR 5

Warranty Card ×1

2. Environmental

The environmental conditions for assuring the copy quality and the

machine operations are as follows:

(1) Normal operating condition

Temperature:20˚C~25

Humidity:65 ±5%RH

(2) Acceptable operating condition

(3) Optical condition

(4) Supply storage condition

3. Production control number(lot No.)

identification

〈Developing cartridge〉

∗:Destination

Division No.

EX Destination A same pack G

B same pack H

Option Destination AP

Humidity (RH)

85%

60%

20%

10˚C30˚C35˚C

Humidity (RH)

90%

60%

15%

–25˚C30˚C40˚C

Humidity (RH)

90%

20%

–5˚C45˚C

Production month

Production day

Destination code

(Dealer, distributor, OEM, etc.)

Production place

(SOCC: Fi ed to B.)

End digit of year

Version No.

DM-1505

3 –1

〈Drum cartridge〉

The label on the drum cartridge shows the date of production.

(SOCC production)

〈JAPAN production〉

Division No.

Ex production 1

Option 2

Same pack 3

∗1 The production control label is not attached to the cartridge of a

China product.

Production month

Production day

Destination code

(Dealer, distributor, OEM, etc.)

Production place

(SOCC: Fi ed to B.)

End digit of year

Version No.

X000119Ver.A 1

Production month

(1 - 9 = Jan. - Sep. 0 = Oct. X = Nov. Y = Dec.)

Serial number of month

Fi ed to 1.

Pack division

(See table below)

End digit of year

Version No.

Production control

label attachment position

Production control

label attachment position(*1)

DM-1505

3 –2

manuals4you.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sharp Photocopieuse

Sharp

Sharp SF-741 Manuel utilisateur

Sharp

Sharp AL-1041 - B/W Laser Printer Manuel utilisateur

Sharp

Sharp AR-5220 Manuel utilisateur

Sharp

Sharp Z-50 Manuel utilisateur

Sharp

Sharp AR-C330 Key operators Manuel utilisateur

Sharp

Sharp MX-C382SC Mode d’emploi

Sharp

Sharp SF-2314 Manuel utilisateur

Sharp

Sharp AR-C262M Key Manuel utilisateur

Sharp

Sharp AL-1650 Manuel utilisateur

Sharp

Sharp AR-151 Manuel utilisateur

Sharp

Sharp AR-206 Manuel utilisateur

Sharp

Sharp AL-1020 Manuel utilisateur

Sharp

Sharp AL-800 Manuel utilisateur

Sharp

Sharp AR-5015 N Manuel utilisateur

Sharp

Sharp AL-800 Manuel utilisateur

Sharp

Sharp AR-281 Manuel utilisateur

Sharp

Sharp AL1215 - B/W Laser - Copier Manuel utilisateur

Sharp

Sharp AR-FX8 Manuel utilisateur

Sharp

Sharp AR-650 Manuel utilisateur

Sharp

Sharp SF-1116 Manuel utilisateur

Sharp

Sharp DM-FX1 Manuel utilisateur

Sharp

Sharp AR-650 Comment utiliser

Sharp

Sharp IMAGER AR-5316 Manuel utilisateur

Sharp

Sharp AR-C240P Mise à jour du firmware

Manuels Photocopieuse populaires d'autres marques

Canon

Canon iR1210 Manuel de référence

Ricoh

Ricoh FW740 Manuel utilisateur

Minolta

Minolta CF910 Manuel utilisateur

Ricoh

Ricoh B003 Manuel utilisateur

Xerox

Xerox EC70 Manuel utilisateur

Oce

Oce 9800 Manuel utilisateur

Olivetti

Olivetti d-Copia 1800 Manuel utilisateur

Minolta

Minolta Di181 Manuel utilisateur

Canon

Canon iR5000i Manuel utilisateur

Telecrane

Telecrane F25 Manuel utilisateur

Xerox

Xerox WorkCentre Pro 40 Manuel utilisateur

Canon

Canon NP6317 Comment utiliser

Ricoh

Ricoh Di-C1 Manuel utilisateur

Mita

Mita MIP-2400 Manuel

Muratec

Muratec MFX-C2280 Manuel utilisateur

Ricoh

Ricoh FT5034C Manuel utilisateur

Minolta

Minolta EP4000 Manuel utilisateur

Ricoh

Ricoh V-C3 Guide d'installation