SereneLife SLRD36WIFI Manuel utilisateur
SLRD36WIFI
by
2
catalog
FCC Information
3
Specification
5
Notice
3
Name of Parts
5
Transmitter Installation
7
Charging Instruction
8
Additional Instruction before Flying
10
Pre-flying Operation
9
Flying Control
11
High / Low Speed Mode
12
Flip Mode
12
Heading Hold Mode
13
Low Battery Alarm
12
Installation of Propeller Guard
6
Landing Gear Installation Diagram
7
Installation and Replacement for Motor and Propeller
13
Operation Instruction for Mobile Phone WiFi
14
Setting
20
Help
21
To record video and take photo
21
Spare Parts
23
Exploded View
22
Troubleshooting Guide
24
3
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.These limits are designed to provide residential
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not Installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception. which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
The equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved
in the instruction manual. Modifications not authorized by the manufacturer may void user’s
authority to operate this device.
FCC WARNING:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on the circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/TV technician for help.
Notice
(1) This product is not an ordinary toy but a piece of complicated equipment
which is integrated with professional knowledge by mechanic, electronic, air
mechanics, high-frequency emission etc., so it should be installed and
adjusted correctly to avoid accidents. The user must always operate in a safe
manner. We undertake no liability for human injury or property damage caused
by improper operation as we could not control the procedure of installation,
use and operation of this drone.
(2) This drone is suitable for experienced RC drone user aged 14 years or above.
(3) The flying field must be legally approved by your local government.
(4) We undertake no liability for those accidents caused by improper operation,
use and control of the drone after sale of the product.
(5) We has entrusted the distributor to provide technology support and after-sale
service. If you have any question about use, operation, repair etc., please
contact your local distributor.
1. Important Statement:
2. Safety Precautions:
Keep away from crowd when flying because a flying RC drone is very dangerous.
Improper assembly, broken main frame, defective electronic equipment or unskilled
operation all may cause unpredictable accidents such as drone damage or human
injury. Please pay special attention to safety operation and have good knowledge
of accident responsibility that the user may cause.
4
(2) Keep away from humid environment
(3) Safe operation
(1) Keep away from obstacles and crowd
The speed and status of a flying RC drone is uncertain and it may cause
potential danger. So the user must keep away from crowd, tall building, power
lines etc. when operating a flying RC drone. Do not fly a RC drone in rainy,
storm, thunder and lighting weather for the safety of user, around people and
their property.
The drone inside is consisted of precise electronic components. Humidity or
water vapor may damage electronic components and cause accident.
Please operate the RC drone in accordance with your physical status and
flying skill. Fatigue, listlessness and improper operation may increase the
rate of accident.
(4) Please strictly obey the order of turn on and turn off before operation. Turn on
the transmitter power first and then turn on the drone power before flying;
turn off the drone power first and then turn off the transmitter power when
finish flying. Improper turn on and turn off order may cause the drone out of
control and threaten people’s safety. Please cultivate a correct habit of turn on
and turn off.
(5) Make sure the connection is solid between battery and motor etc. The ongoing
vibration may cause bad connection of power terminal make the drone out of
control.
(7) The drone should be controlled within max control distance. Do not fly the
drone near tall building, high voltage cable or other place with signal interference.
Or may cause signal interruption and the drone will be out of control, which
may result in accident.
(6) Improper operation may cause drone crash, which may arouse motor
defective and noise, and then effect the flying status or even stop flying.
Please go to the local distributor to buy new parts for replacement so that the
drone will return to its best status.
(1) Flying field must be spacious enough and we suggest at least
8M (length)*8M (width)*5M (height).
(2) Make sure the drone battery and transmitter battery are fully charged.
(3) Make sure the Left Stick of the transmitter in the lowest position.
3. Check List Before Flight
(4) Keep away from rotating parts
Rotating Parts can cause serious injury and damage. Keep face and body
away from rotating motors.
(5) Keep away from heat
(6) Please do not touch the hot motor to avoid being burnt.
The RC drone is made of metal, fiber, plastic, electronic components etc.
Keep away from heat and sunshine to avoid distortion and damage.
5
Specification
Drone Size
Drone Weight
Propeller Diameter
Flying Time
480x480x120mm
355g
190mm
6~7mins
Camera Resolution 1280x720P
35 m
100 m
Drone Battery 3.7Vx2 1000mAh
Charging Time for Drone Battery 140~160mins
Max Flying Distance/Radius
Max Image Transmission
Distance/Radius
1. Drone
Name of Parts
B Propeller
Counterclockwise
A Propeller
Clockwise
A Propeller
Clockwise
B Propeller
Counterclockwise
Picture 1
Picture 2
Eye Lights
Front
Left Right
Rear
Propeller Guard
Rear LED Lights
(Green)
Front LED Lights
(White)
6
Picture 3
Picture 4
Flip Mode IconHeading Hold Mode Icon
High / Low Speed Mode Icon
2. Transmitter
Power Indicator Light
Mobile Phone Screen Lens Hood
Power Switch
Right Stick (Forward /
Backward / Left / Right)
Forward / Backward
Trimmer
Left / Right Trimmer
Flip Mode
Left Stick
(Throttle / Rudder)
Rotation Trimmer
Heading Hold Mode
High / Low Speed Mode
LCD Screen Indication
Direction of
Power Switch
Installation of Propeller Guard
1. Install the propeller guard to the drone and make sure the propeller guard’s pillar can fully fill
the gap. Then lock the propeller guard by attached 1.7*6PB screw (short screw).
2. Remove the screw from the propeller guard and pull out the propeller guard with moderate
force.
3. To improve the drone power and flight time, fly the drone without the propeller guard when
you can operate the drone skillfully.
1.7*6PB Screws
7
Landing Gear Installation Diagram
To install the Landing Gear, insert the Landing
Gear’s pillars into the drone body holes with
moderate force as the diagram shown.
Note: Please ensure the Landing Gear can
stand firm on the ground. Or the flight
stability would be effected.
Picture 5
Transmitter Installation:
Battery installation: open the battery cover on the back side of the transmitter and
put 4 alkaline batteries (not included) into the box in
accordance with electrode instructions.
Picture 6
Battery Cover
4X1.5V
Alkaline Batteries
Drive the screw according to
the arrow direction to loosen
the screw to open the battery
cover. Tighten the screw by
driving it in opposite direction.
1. Make sure the electrodes are correct.
2. Do not mixed use new and old batteries.
3. Do not mixed use dierent kinds of batteries.
4. Do not charge the non rechargeable battery.
Notice：
Attaching your Mobile Phone to Transmitter
1. Press the self-locking switch on the top right side of the mobile holder and
push the holder to a fully open position as Picture 7 shown.
2. Place the mobile phone facing frontward position, pull the mobile phone holder
down and press tightly as possible to secure the mobile phone and transmitter
(please note that do not touch the mobile phone button) as Picture 8.
8
3. Insert the lens hood to the slot and make
sure the lowe edge of the lens hood next
to the mobile phone closely as Picture 9.
Picture 9
Charging Instruction
Drone Battery
Picture 7 Picture 8
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household trash.
Please contact local environmental or waste agency or the supplier of your
model or your nearest Li-Po battery recycling center.
1. Connect the USB wire with one of the USB port listed in the below picture first, and
then connect the drone battery with the USB wire. (prior to choose 2A, 5V charger)
2. After connecting the USB wire with the USB port, the green USB indicator light
keeps bright. After connecting the USB wire with the drone battery, the red USB
indicator light keeps bright. About 140~160 minutes later, the light turns to green
and keeps bright when fully charged.
3. Li-Po battery is included in spare parts and please pay attention on the safe notice.
* Do not put the battery on high temperature place, such as fire or heating device
to avoid damage or explode.
* Do not use the battery to crash or hit hard surface.
* Do not put the battery in water and keep it in dry place.
* Do not open the battery.
* Do not leave the battery without supervision when charging.
* Make sure that there is no short circuit of the power wire.
* Please use the recommended charger only.
* Check the charger’s wire, plug, surface regularly. Do not use broken charger.
9
Picture 10
1. Turn on the transmitter switch (Picture 10) and its indicator light flashes quickly.
Push the Left Stick to utmost control distance and then to the low end (Picture 11/12).
The indicator becomes flash slowly, which indicates the transmitter enters frequency
pairing.
Pre-flying Operation:
Picture 12Picture 11
Picture 13
Picture 14
2. Press the battery box buckle at the tail of the drone and then pull it out (Picture 13).
3. Connect the battery plug with the drone plug (Picture 14).
Press and pull out
Note: The drone or the battery may damaged for wrong connection of the plug.
Power On
Picture 15
4. Push the battery to the drone body and make sure the connective plugs are placed well.
10
Additional Instruction before Flying:
1. The white light is front (head).
2. Power on the drone and check the rotating propellers. The left front and right rear
propellers rotating clockwise while the right front and left rear propellers rotating
counterclockwise.
3. Adjust relative transmitter Trimmer button to adjust the rudder if the drone tilts to one side
when flying.
4. The transmitter will beep constantly when the drone battery is low. Please land the drone
as soon as possible after low battery alarm.
Please follow below steps to calibrate the drone if the drone becomes imbalance after
crashing during the flight, or can not be adjusted by trimmer button and cause difficult
operation.
5. Calibration Instruction
1) Turn off the drone switch and then turn off the transmitter switch.
2) Turn on the transmitter switch, push the Left Stick all the way up to the utmost position
and then pull it back to the lowest position (See Picture 17 and 18), and the transmitter
enters the state of code pairing waiting.
Picture 17 Picture18
Picture 16
5. Insert the TF card to the card slot at the rear part of the camera, and then turn on the
power switch. The LED lights start to flash. Put the drone on the horizontal position to
calibrate the gyro. The transmitter beep constantly about three seconds later, which
indicates successful code pairing and the LED lights get a solid bright.
Note: When insert the card to the slot, ensure the metal side of the TF card is
shown as Picture 16.
OFF ON
2. Turn on the switch
1. Insert the TF Card to the slot
Table des matières
Autres manuels SereneLife Drone
