Serene S2059 Mode d'emploi
Recessed Wall Mounted
Fan Heater S2059
Specification & Operating
Instructions
Introduction
Designed for easy installation, your Serene S2059 Recessed Wall Mounted Fan Heater is
designed to fit easily into existing walls and is designed to fit most existing Skope cut-
outs.
Important
Safety Information
•When using any electrical appliance, safety precautions should always be observed.
Read these instructions carefully, and retain for future reference. For service, contact
your nearest authorised service agent.
•Under no circumstances should an unauthorised person open the heater to adjust
the thermostat.
•This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
•Children should be supervised to ensure that they do not play with the appliance.
Do NOT use this appliance other than for its intended use.
•Use this appliance only with the voltage specified on the rating label.
•Be very careful not to touch hot surfaces or moving parts.
•Do NOT cover the grilles or place any object or material up against the unit as this
may block the entry or exhaust of airflow.
•Do NOT probe any opening to remove fluff. To ensure trouble-free performance, it is
recommended that the unit be isolated from the power supply and a vacuum cleaner
used to remove dust and fluff from the inlet and outlet grilles on a regular basis.
•If Hard Wiring Installation,this must be performed by a licensed electrician.
Regulations require that electrical work be carried out only by properly qualified
person. For your own safety and that of others, ensure this is done.
•Do NOT allow any supply cord to come into contact with heated surfaces during
operation.
•If the supply cord becomes damaged, it must be replaced by a qualified Electrician
in order to avoid a hazard.
Distances:
This heater is NOT designed to be mounted high.
The heater must be mounted minimum distances of 200mm from floor level and 300
mm from any adjacent wall.
Installation:
This appliance MUST be installed in accordance with relevant wiring rules and
regulations which cover installation of appliances and accessories in damp situations,
such as bathrooms, showers, laundries and other areas, fixed water containers.
For additional protection, it is strongly recommended that the use of a residual
current device (RCD) with a tripping current not exceeding 30mA be used on the
circuit supplying this product.
The S2059 recessed model wall fan heaters are designed to be permanently wired
and recessed into the wall.
To install the heater, follow the instructions
below:
•Cut a hole in the wall. (fig 1) The positioning and hole dimensions are shown in
the installation diagram. The minimum required height from the floor to the base
of the heater and the distance from any adjacent wall is 300mm.
The hole must be between wall studs.
Adjacent wall
Hole in wall dimensions
Floor level
Minimum 200 min.
380
300 mm
Fixing screws (6)
Min 94mm deep
Fig 1
HEATER BODY
•It is recommended to
line top and bottom of the hole
with Gibraltar board or hardboar
d for the best result. If the cut-
out is not to the recommended
size, the wall studs may need to
be packed out with timber to
provide firm fixing surfaces.
Installation (cont):
•Remove the 4 screws from the front panel (per fig 2 below)
This will allow the front panel to be pulled away from the body.
•Once the front panel is loose disconnect the 2 connecters as shown (per fig 3) below.
The front panel is then totally disconnected from the body.
•Line top and bottom of the hole with Gibraltar board or hardboard.
•If the cutout is not to the recommended size, the wall studs may need packed out with
timber to provide firm fixing surfaces Fit the heater body into the hole by screwing
the 6 fixing screws into the sides of the hole (screws provided)
•Connect the mains cable as needed.
•Reconnect the 2 wiring connectors. Ensuring that they are properly in place.
•Replace the front panel into position and insert the 4 fixing screws in place ensuring that
they are tightened.
Position of screws
Fig 2
Connector 2
Disconnect connectors
Fig 3
Operation:
On/ Off and
fan speed
heat control
Thermostat Temperature
Rotational Control
ON light
Thermostat
light
Push knobs
inwards to recess
flush to front.
Push again to
extend
•The operation of the heater is controlled by the HI/ MED/LOW/OFF control knob.
•The adjustable thermostat knob is located on left of the heater.
•The blue LED indicators light when the heater is operating.
•The heat output is regulated by a built-in thermostat. The thermostat
maintains the required ambient temperature by automatically turning
the heat on and off as needed.
Starting from the lowest position, turn the thermostat knob
clockwise until you hear a ‘click’. The heater will then start heating and
the LED indicator will light up. The more the thermostat knob is turned
clockwise, the higher the ambient temperature will be.
•If the ambient temperature is close to 35°C or more, the heater may not
turn on even if the thermostat is set on maximum. Alternatively, if the
ambient temperature is below 5°C, the heater may operate in ‘frost guard ‘mode
continuously even if the thermostat is set on minimum.
To set the thermostat:
•Turn the thermostat knob clockwise to maximum and wait until a comfortable
ambient temperature is reached.
•Turn the thermostat knob anti-clockwise until you hear a ‘click’ and the heater
turns off.
•Fine adjustments can then be made as needed.
Safety Cutout:
Your Serene S2059 Wall Fan Heater is fitted with an auto-reset thermal cutout and a
fusible link. Either of these devices will automatically switch off the elements and the
motor, should the unit reach an abnormal temperature.
Should this occur, disconnect the heater from power supply, check for blockageof the air
inlet and outlet, and use a vacuum cleaner to clean if necessary.
If the heater still fails to operate, contact your supplier after first checking that there is
power to the unit and that the thermostat is not set to maximum or minimum..
Specifications: Serene S2059:
Electrical
Supply 230-240 volts A.C. 50 Hz
Wattage 2200-2400W, thermostatically controlled.
Wiring Permanent connection. Earth required.
Ingress Protection Rating IP20
Dimensions
Height 435 mm
Width Front panel 380mm
Width back 345 mm
Depth main unit 88 mm
Depth front panel 28 mm - including knobs extended
Weight 4.8kg
Serene Industries Limited reserves the right to alter both design and specifications without notice.
Serene offers a full replacement warranty. We do NOT supply any spare parts or include any service guarantee.
Operation (cont):
435mm
380mm
345mm
Contact:
HONG KONG
Head Office - Serene Industries Limited
t: +852 2325 3209
f: +852 2325 3166
e: info@serene-ind.com
w: www.serene-ind.com
Suite 1010, 10F, Block A, Alexander Industrial Building, 62 King Lam Street,
Cheung Sha Wan, Kowloon Hong Kong SAR
NEW ZEALAND
t: (+) 64 (3) 344 5550
f: 0800 437 264- Freefax
e: nzenquiry@sereneind.com
w: www.serene-ind.com
PO BOX 33501, Barrington, Christchurch 8024
AUSTRALIA
e: auenquiry@serene-ind.com
w: www.serene-ind.com
UNITED KINGDOM
t: +44 (0)1624 497794
e: ukenquiry@serene-ind.com
w: www.serene-ind.com
Rowhead House, Far Common Road Mirfield, West Yorkshire WF140DQ
Table des matières
Autres manuels Serene Chauffage
Serene
Serene Classic Manuel utilisateur
Serene
Serene S2067 Manuel utilisateur
Serene
Serene Sirio S2029 Manuel
Serene
Serene Optima S2055 Manuel utilisateur
Serene
Serene S2077 Manuel utilisateur
Serene
Serene S2068 Manuel utilisateur
Serene
Serene S2077 Manuel utilisateur
Serene
Serene S2066 Manuel utilisateur
Serene
Serene S6069 Apollo Manuel utilisateur
Serene
Serene S2026 Manuel
Manuels Chauffage populaires d'autres marques
oventrop
oventrop Regucor Series Manuel utilisateur
Blaze King
Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur
ELMEKO
ELMEKO ML 150 Manuel utilisateur
BN Thermic
BN Thermic 830T Manuel utilisateur
KING
KING K Series Mode d’emploi
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Guide de démarrage rapide
Empire Heating Systems
Empire Heating Systems WCC65 Manuel utilisateur
Wetekom
Wetekom 92 86 43 Manuel utilisateur
Desa
Desa SPC170-F Manuel utilisateur
Watlow
Watlow Watrod Electric Tubular Heaters Manuel utilisateur
Haverland
Haverland ECO-DRY GPS Series Manuel de la liste des pièces
Stelpro
Stelpro ASILVC2060 Series Manuel utilisateur