Serene S2044 Manuel

Instructions &

Operation Manual

Model S2044

Wall Mounted Space Heater

Safety Information:

This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety.

When using any electrical appliance, safety precautions should always be

observed. Read these instructions carefully, and retain for future

reference.

When used by, or near, young children or infirm persons, supervision is

necessary - young children should be supervised to ensure that they do

not play with the appliance.

Use this appliance only with the voltage specified on rating label.

Do NOT use this appliance other than for its intended use.

Do NOT touch hot surfaces or moving parts.

Do NOT cover the grilles or place any object or material up against the

unit, as this may block entry or exhaust of air.

Do NOT probe any opening.

To ensure trouble free performance it is recommended that on a regular

basis the unit be isolated from the power supply and a vacuum cleaner

used to remove dust from the inlet and outlet grilles.

Caution:

When the heater is operated ensure the heater is not obstructed in

any way. Ensure the heater can operate safely, should the heater switch on

when the ambient temperature drops, or a timer activates the heater.

Do NOT allow the supply cord to come into contact with heated

surfaces during operation.

Regulations require that electrical work be carried out by authorised

persons. For your own safety and that of others, ensure this is done.

If the supply cord becomes damaged, it must be replaced by a

qualified person, in order to avoid a hazard

Positioning

This heater is water resistant to IP24.It can therefore be used in

bathrooms or other areas subject to humidity, The heater must be

installed so that switches and other controls cannot be touched by a

person in the bath or shower.

The heater must be mounted on the wall, with a minimum height of 300mm

above the floor or any other objects heated below it, and a minimum

distance of 400mm below the ceiling and from adjacent walls.

The heater must not be located immediately below a socket outlet.

Ensure that the heater is not mounted in a situation where the heated air is

directed over an open door, curtains, or any towel rail, creating a fire risk.

Leave at least 1 metre of space in front of the heater to allow correct air

delivery.

The heater must be mounted a minimum distance of:

300mm above floor level or any other objects heated below it

Wall

Floor

Wall 400mm

Min.

400mm

Min.

300mm

Min.

Thermostat

The heat output is regulated by a built-in thermostat. The thermostat maintains the

required ambient temperature by automatically turning the heater on and off.

Starting from the ‘Freeze Guard’ position, turn the thermostat knob

clockwise until you hear a ‘click’. The heater will then start heating and the LED

indicator will light up. The more the thermostat knob is turned clockwise, the higher

the ambient temperature will be.

If the ambient temperature is close to 30°Cor more, the heater may not turn on even

if the thermostat is set on maximum. Alternatively, if the ambient temperature is below

5°C, the heater may operate continuously even if the thermostat is set on

minimum.

To set the thermostat:

1.Turn the thermostat knob clockwise

to maximum and wait until a

comfortable ambient temperature is

reached.

2.Turn the thermostat knob anti-

clockwise until you hear a ‘click’ and

the heater turns off.

3. Fine adjustments can then be made.

Freeze Guard

When the thermostat knob is turned fully anti-clockwise, pointing to the

‘Freeze Guard’ symbol, the heater will operate if the room

temperature falls below 5°C.

Note: This heater does not have an on/off switch. To turn the heater off it

must be turned off at the wall switch.

LED Indicator

FreezeGuard

ThermostatKnob

Filter

This heater is fitted with an air filter to

protect the heating elements from dust

and dirt. The filter is removable and can

be fitted from either the left or right hand

side of the heater.

To keep the heater operating efficiently,

remove and clean the filter once every six

months. Ensure the filter is always

fitted before operating the heater.

Safety Cutout

AirFilter

This heater is fitted with a thermal safety cutout device. In the case of over-heating,

the safety cutout automatically switches off the heating elements and fan motor. As

a result, the heater stops working but the LED indicator stays on.

Note: If the heater switches off, the LED indicator may also turn off when the

room temperature reaches the thermostat setting.

If the safety cutout is activated:

1. Turn the heater off at the wall switch and leave to cool for

approximately 30 minutes.

2. Check the air filter and clean if necessary. Ensure the filter is fitted

again before operating the heater.

3. Eliminate any other possible reason for overheating (such as

obstacles in front of the air inlet and outlet grille).

4. Turn the heater on and check operation. If the heater still fails to

operate, contact your nearest authorised service agent.

Care

The heater is best wiped down from time to time with a damp cloth. Do not

use any abrasive cleaners.

Specifications

Dimensions

Height:430mm

Width:270mm

Depth: 135mm

Weight:3.0 kg

Electrical

Wattage: 2000-2200 Watts

Supply: 230-240 Volts a.c. 50 Hz.

Wiring:Permanent connection. Double Insulated - no earth required.

Ingress Protection Rating: IP24

Contacts:

HONG KONG

Head Office - Serene Industries Limited

t: +852 2325 3209

f: +852 2325 3166

e: [email protected]

w: www.serene-ind.com

Suite 1010, 15F, Block A, Alexander Industrial Building,

62 King Lam Street,

Cheung Sha Wan, Kowloon Hong Kong SAR

NEW ZEALAND

t: (+) 64 (3) 344 5550

f: 0800 437 264- Freefax

e: nzenquir[email protected]

w: www.serene-ind.com

PO BOX 33501, Barrington, Christchurch 8024

AUSTRALIA

t: + 61 (3) 8354 4133

f: + 61 (3) 9699 6422

fp: +1800 561 961- Freephone

e: enquiries@serene-australia.com

w: www.serene-australia.com

Suite 201 / 175B Stephen Street, Yarraville

Melbourne VIC 3013

Table des matières

Autres manuels Serene Chauffage

Serene

Serene S2066 Manuel utilisateur

Serene

Serene S2077 Manuel utilisateur

Serene

Serene S2067 Manuel utilisateur

Serene

Serene S2077 Manuel utilisateur

Serene

Serene S2022 Mode d’emploi

Serene

Serene S2033 Manuel

Serene

Serene S2044 ROMA Manuel utilisateur

Serene

Serene S6068 Sorroco Manuel utilisateur

Serene

Serene S2059 Mode d'emploi

Serene

Serene S2026 Manuel

Serene

Serene Sirio S2029 Manuel

Serene

Serene Optima S2055 Manuel utilisateur

Serene

Serene S2068 Manuel utilisateur

Serene

Serene S2212 Manuel

Serene

Serene Classic Manuel utilisateur

Serene

Serene S2077 Manuel utilisateur

Serene

Serene S2088 Manuel utilisateur

Serene

Serene S6069 Apollo Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur