Senva TG Series Manuel utilisateur

User’s Guide

TG Series

Senva Sensors

9290 SW Nimbus Ave

Beaverton, OR 97008

154-0031-0C

Rev. Release Date By Description of Change ECR

4/14/2016

CKB

Initial Release

---

3/7/2017

CKB

Updated for RS485 version.

---

9/12/2017

CKB

Added “Periodic Test and Maintenance” section

---

information, and may not be reproduced or distributed without written permission.

User’s Guide, TG Series Page 2 of 17 154-0031-0C

Contents

General Overview.................................................................................................................................................................................... 3

User Menu .................................................................................................................................................................................................. 4

 ................................................................................................................................................................................................ 5

 / .................................................................................................................................................................................. 5

................................................................................................................................................................................................... 7

 ................................................................................................................................................................................... 8

................................................................................................................................................................................. 9

...............................................................................................................................................................................10

 ......................................................................................................................................................................................10

 ......................................................................................................................................................................................11

 ..............................................................................................................................................................................................11

 ...........................................................................................................................................................................................12

Setup Menu..............................................................................................................................................................................................13

 ........................................................................................................................................................................................................13

......................................................................................................................................................................................................14

Testing Menu ..........................................................................................................................................................................................15

Idle Condition Codes............................................................................................................................................................................16

Periodic Test and Maintenance........................................................................................................................................................17

References:

152-0270 TG Series Analog Installation Instructions

152-0271 TG Series RS485 Installation Instructions

152-0272 TG Series Hose Barb Installation Instructions

152-0273 TG Sensor Replacement Instructions

154-0032 BACnet Protocol Guide

154-0033 Modbus Protocol Guide

User’s Guide, TG Series Page 3 of 17 154-0031-0C

General Overview

The TG product contains 3 menu systems:

•User Menu – Configure system functions setpoints, such as relay setpoints and analog output

scaling.

•Setup Menu – Add/Remove sensors, and view sensor information.

•Testing Menu – Test functionality of system interfaces, such as relays and analog output signals.

Each menu is composed of a hierarchy of primitive elements: Categories, Items, Numerical Values, and Option

Values. Categories give you access to Items, which may contain either Numerical Values when the setting is

numerical, or Option Values when the setting is multiple choice. A list of available Categories is shown at the

top of each menu in this document. See Figure 1 below for an example.

Default

0-10V

Quickstart

User Menu

0-5V 4-20mA 1-5V

Menu Category Item Option Values

0-120

(minutes)

Fan Relay

Min

Time

Numerical Value

Item

Figure 1: The “Quickstart” category contains an Item ‘A’, which has a set of multiple choice option values. The

“Fan Relay” category has an Item ‘Min On Time’ (



) which can be set to any Numerical Value between 0-120 in

minutes.

Buttons

•◆– “Select” button.

•▲– “Inc” button (Increment).

•▼– “Dec” button (Decrement).

Navigation and Selection

•Pressing ▲or ▼while viewing a Category/Item advances to the next or previous Category/Item.

•Pressing ▲or ▼while viewing a Numerical Value increments or decrements the value.

•Pressing ▲or ▼while viewing an Option Value scrolls through the available options.

•Pressing ◆while viewing a Category allows you to view the items it contains.

•Pressing ◆while viewing an Item allows you to view and modify the Values/Options for that Item.

•Pressing ◆while viewing a Value/Option applies your selection and returns you to the Item view.

•Hold ▲, ▼, and ◆for 1 second while the alarm buzzer is active to suppress the alarm.

•Each Menu contains an



Item, which will exit the current menu.

•Each Category contains an



Item, which will return you to the previous Menu screen.

*Unless otherwise specified, all changes to Numerical Values/Option Values occur at the time

▲

▼

is pressed.





SEL

INC

DEC

User’s Guide, TG Series Page 4 of 17 154-0031-0C

User Menu

Access the User Menu by pressing the ◆button for one second.The User Menu organizes settings into

several categories. Many of these settings can also be modified over BACnet or Modbus. The

object/instance number is noted in each modifiable value. See the relevant protocol guide for more

information.

Categories

•Quickstart (



)

Allows the user to select from a list of pre-defined configurations for quick and easy startup.

•Analog Output Channel 1 (



)

Contains all of the settings which control the output signal on channel 1. (Analog Version only)

•Analog Output Channel 2 (



)

Contains all of the settings which control the output signal on channel 2. (Analog Version only)

•RS485 (



)

Manually set the RS485 communication settings. (RS485 Version only)

•CO Setpoints (



)

Contains all of the user configurable setpoints, which control the system response to the CO Gas Sensor.

(CO Sensor only)

•NO2Setpoints (



)

Contains all of the user configurable setpoints, which control the system response to the NO2 Gas

Sensor. (NO2Sensor only)

•Temperature Setpoints (



)

Contains all of the user configurable setpoints, as well as unit selection, which control the system

response to the thermistor.

•Fan Relay (



)

Configure the timing of the fan relay (warning relay).

•Alarm Relay (



)

Configure the timing of the alarm relay. (Analog Version only)

•Buzzer (



)

Configure the timing of the alarm buzzer.

•Display (



)

Customize the performance of the display.

User’s Guide, TG Series Page 5 of 17 154-0031-0C



Applies the following setpoints to their respective sensors:

CO Warning = 25, CO Alarm = 100, NO2 Warning = 1, NO2 Alarm = 3 (in PPM), Buzzer Delay = 30 (minutes).



0-10V Output Range (Default)



1-5V Output Range (Analog Version Only)



4-20mA Output Range (Analog Version Only)



0-5V Output Range (Analog Version Only)

Applies the following setpoints to their respective sensors:

CO Warning = 15, CO Alarm = 50, NO2 Warning = 0.7, NO2 Alarm = 2 (in PPM), Buzzer Delay = 30 (minutes).



0-10V Output Range



1-5V Output Range (Analog Version Only)



4-20mA Output Range (Analog Version Only)



0-5V Output Range (Analog Version Only)

Applies the following setpoints to their respective sensors:

CO Warning = 35, CO Alarm = 100, NO2 Warning = 1, NO2 Alarm = 5 (in PPM) , Buzzer Delay = 30 (minutes).



0-10V Output Range



1-5V Output Range (Analog Version Only)



4-20mA Output Range (Analog Version Only)



0-5V Output Range (Analog Version Only)

Applies the following setpoints to their respective sensors:

CO Warning = 5, CO Alarm = 10, NO2 Warning = 0.5, NO2 Alarm = 1 (in PPM) , Buzzer Delay = 2 (minutes).



0-10V Output Range



1-5V Output Range (Analog Version Only)



4-20mA Output Range (Analog Version Only)



0-5V Output Range (Analog Version Only)

Returns to the User Menu screen.





Selects the output mode of the analog output signals. Changing this setting on either 

or  sets the output mode on both analog output channels.



Voltage Out (Default)



Current Out













User’s Guide, TG Series Page 6 of 17 154-0031-0C

Selects the sensor to be output on output channel 1 () or output channel 2 (). By

default, if a single sensor is present it will be configured on output channel 1. If two sensors are

present, CO will default to output channel 1, while the NO2 sensor will default to output

channel 2.



No sensor selected.



CO Gas.



NO2 Gas.



Temperature.

Sets the voltage corresponding to the maximum sensor reading, 0-10 Volts.

Default:  Volts

Sets the voltage corresponding to the minimum sensor reading, 0-10 Volts.

Default: Volts

Sets the current corresponding to the maximum sensor reading, 4-20 Milliamps.

Default:  Milliamps

Sets the current corresponding to the minimum sensor reading, 4-20 Milliamps.

Default: Milliamps

Returns to the User Menu screen.













User’s Guide, TG Series Page 7 of 17 154-0031-0C



Sets the RS485 address. The full address range 0-254 is supported. When at address 255, this is

considered “AUTO ADDRESSING” mode (see TG BACnet/Modbus Protocol Guides), and will show

up as ““ on the LCD display if an automatic address has not been detected and configured.

Once an address has been selected in auto mode, the address will show up in this field along

with an “O/R” symbol in the bottom center of the LCD to indicate this address was

automatically selected by the TG.

RS485 Version Only: AV123 (BACnet), R123 (Modbus).

Default:  (Auto Mode)

Sets the Ones digit of the device id. The max device id is 4,194,302

If the combination of id.1 and id.2 exceed 194,302, then the max value that may be set it the

id.3 field is 3.

Example: To set the device id to 1,234,567 each id field should be as follows 1

.3

234

.2

567

.1

Default: Varies

Sets the Thousands digit of the device id. See .

Default: 665

Sets the Millions digit of the device id. See .

Default: 0

Sets the RS485 baud rate.

RS485 Version Only: AV124 (BACnet), R124 (Modbus).



Auto Baud Rate (Default)



9600 Baud



19,200 Baud



28,800 Baud



38,400 Baud



57,600 Baud



76,800 Baud



115,200 Baud



230,400 Baud



460,800 Baud

Sets the RS485 protocol.

RS485 Version Only: MSV122 (BACnet), R122 (Modbus).



Auto Protocol (Default)



BACnet



Modbus ASCII



Modbus RTU













User’s Guide, TG Series Page 8 of 17 154-0031-0C

Sets the RS485 parity.

RS485 Version Only: MSV126 (BACnet), R126 (Modbus).



Auto Parity (Default)



No Parity



Odd Parity



Even Parity

Sets the RS485 data bits.

RS485 Version Only: R127 (Modbus accessible only).



Auto Data Bits (Default)



7 Data Bits



8 Data Bits

Sets the RS485 stop bits.

RS485 Version Only: R128 (Modbus accessible only).



Auto Stop Bits (Default)



Stop Bit



1.5 Stop Bits



2 Stop Bits

Returns to the User Menu screen.



Sets the alarm setpoint level in PPM. Accepts any value between 0-1000 in whole PPM.

RS485 Version Only: AV152 (BACnet), R152 (Modbus).

Default:  PPM

Sets the warning setpoint level in PPM. Accepts any value between 0-1000 in whole PPM.

RS485 Version Only: AV150 (BACnet), R150 (Modbus).

Default:  PPM

Sets the setpoint hysteresis, in PPM. The setpoint hysteresis defines how far below the

Warning/Alarm setpoint the sensor value must drop before changing state from Alarm to

Warning or Warning to Normal.

RS485 Version Only: AV154 (BACnet), R154 (Modbus).

Default: PPM















User’s Guide, TG Series Page 9 of 17 154-0031-0C

Sets the value in PPM which corresponds to the maximum analog output signal range. Accepts

any value between 0-1000 in whole PPM. (Analog Version Only)

Default:  PPM

Sets the value in PPM which corresponds to the minimum analog output signal range. Accepts

any value between 0-1000 in whole PPM. (Analog Version Only)

Default: PPM

Returns to the User Menu screen.



Sets the alarm setpoint level in PPM. Accepts any value between 0-20 in whole PPM.

RS485 Version Only: AV162 (BACnet), R162 (Modbus).

Default: PPM

Sets the warning setpoint level in PPM. Accepts any value between 0-20 in whole PPM.

RS485 Version Only: AV160 (BACnet), R160 (Modbus).

Default: PPM

Sets the setpoint hysteresis, in PPM. The setpoint hysteresis defines how far below the

Warning/Alarm setpoint the sensor value must drop before changing state from Alarm to

Warning or Warning to Normal.

RS485 Version Only: AV164 (BACnet), R164 (Modbus).

Default: PPM

Sets the value in PPM which corresponds to the maximum analog output signal range. Accepts

any value between 0-20 in whole PPM. (Analog Version Only)

Default:  PPM

Sets the value in PPM which corresponds to the minimum analog output signal range. Accepts

any value between 0-20 in whole PPM. (Analog Version Only)

Default: PPM

Returns to the User Menu screen.



















User’s Guide, TG Series Page 10 of 17 154-0031-0C



Selects the temperature display units.

RS485 Version Only: MSV133 (BACnet), R133 (Modbus).



Degrees Celsius



Degrees Fahrenheit (Default)

Sets the value which corresponds to the maximum analog output signal range. Accepts any

value between -20°C (-4°F) and 85°C (185°F) in whole degrees. (Analog Version Only)

Default:  °F

Sets the value which corresponds to the minimum analog output signal range. Accepts any

value between -20°C (-4°F) and 85°C (185°F) in whole degrees. (Analog Version Only)

Default:  °F

Returns to the User Menu screen.



Sets the minimum time, in minutes, which the relay must be active before it can turn off.

Accepts any value between 0-120 in whole minutes.

RS485 Version Only: BO210 minimum on time (BACnet), R214 (Modbus).

Default: Minute

Sets the minimum time, in minutes, which the relay must be inactive before it can turn on.

Accepts any value between 0-120 in whole minutes.

RS485 Version Only: BO210 minimum off time (BACnet), R216 (Modbus).

Default: Minute

Sets the maximum time, in minutes, which the relay can be inactive. Accepts any value

between 0-1440 in whole minutes. If set to ‘0’ the maximum off time will be infinite.

RS485 Version Only: AV212 (BACnet), R212 (Modbus).

Default: Minutes

Returns to the User Menu screen.

















Autres manuels pour TG Series

Table des matières

Autres manuels senva Accessoires

senva

senva TG Series Manuel utilisateur

senva

senva TG Series Manuel utilisateur

senva

senva TotalSense Series Manuel utilisateur

senva

senva TG Series Instructions d'installation et d'utilisation

senva

senva TG Series Manuel utilisateur

senva

senva TG Series Manuel utilisateur

senva

senva TotalSense Series Manuel utilisateur

senva

senva AQ Series Manuel utilisateur

senva

senva TotalSense Series Manuel utilisateur

senva

senva TG Series Manuel utilisateur

senva

senva CHTWL Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur