Sentry360 IS-IP200-IRB Manuel utilisateur
©Sentry360 2014
IS-IP200-IRB, 220-IRB-30
User Manual
Ver 1.0
Table of Contents
1. Overview............................................................................................................................ 3
1.1 Features ...................................................................................................................... 3
1.2 Package Contents........................................................................................................ 4
1.3 Dimensions.................................................................................................................. 5
1.4 Connectors .................................................................................................................. 6
2. Camera Cabling................................................................................................................. 8
2.1 Connect Power............................................................................................................ 8
2.2 Connect Ethernet Cable............................................................................................... 8
2.3 Connect Alarm I/O........................................................................................................ 8
3. Installation......................................................................................................................... 9
3.1 Ceiling / Wall Mounting ................................................................................................ 9
4. System Requirements .....................................................................................................11
5. Access Camera ................................................................................................................12
6. Configure Video Streams ................................................................................................16
7. Configuration Files Export / Import ................................................................................17
Appendix A: Delete the Existing DC Viewer..........................................................................18
Appendix B: Setup Internet Security.....................................................................................19
1. Overview
The IS-IP200-IRB camera is a Quad-streaming, H.264 & MJPEG encoding, 2.0 Megapixel
resolution, IP-addressable, network camera. It is designed to deliver full-motion, high-definition,
progressive scan digital video across local area networks. The IS-IP200-IRB features a design
with no moving parts, a 1/2.7” CMOS sensor, Power over Ethernet, 23 built-in IR-LEDs, and
Audio-In/Audio-Out. The IS-IP200-IRB is a cost effective, high-level, megapixel network camera.
1.1 Features
•Progressive Scan CMOS Sensor
•Quad Streams support
•Dual Streams, Full HD 1080P real-time + D1 real-time
•Quad Streams Compression:
H.264 Baseline / Main / High Profile + MJPEG
•Multi-language support
•Tampering Alarm
•Wide Dynamic Range
•Remote Zoom & Focus (Motorized Lens)
•Motion Detection
•Privacy Masks
•Smart Picture Quality / 3D Noise Reduction
•Vertical View Mode (Image rotation by 90 derees)
•Smart IR Mode
•Network Failure Detection
•Day/Night (ICR)
•IR LED Module (working distance up to 25m)
•Micro SD support
•Weatherproof (IP66 International)
•Sunshield
•Integrated Mounting Bracket with Cable Management
•ONVIF Support
1.2 Package Contents
Please check the package contains the following items listed below.
Camera (Cable included)
Power Terminal Block (x1)
M4 Inner Hex Wrench (x1)
Alarm Terminal Block (x1)
Plastic Screw Anchors (×5)
M4 Self Tapping Screws (×5)
Desiccant
Desiccant User Guide
Quick Guide
1.3 Dimensions
The IS-IP200-IRB dimensions are shown below.
1.4 Connectors
The diagram below shows the IS-IP200-IRB reset button and various connectors. Definition for
each connector will be given as follows.
All-in-one Cable
No
Cable
Pin
Definition
Remarks
1
Network (with PoE)
-
RJ-45 connector with LED
2 Power
(3-pin Terminal Block)
1
AC 24V-1
DC (-)
Power connection
2
GND
Reserved
3
AC 24V-2
DC (+)
3 Alarm
(4-pin Terminal Block)
1
ALM_DI
－
Alarm connection
2
ALM_DI
＋
3
ALM_DO
－
4
ALM_DO
＋
4 Audio I/O
Pink
Line In/ Mic In
Two-way audio
transmission
Green
Line Out
5
BNC
-
Analog Video Output
Micro SD Card Slot / Reset Button
Follow the steps below to reach the Micro SD Card Slot, Reboot Button and Factory Default
Button on the Camera:
Step 1. Unscrew the screw on the
camera housing and carefully
remove the front housing.
Micro SD Card Slot
Factory Default Button
Reboot Button
NOTE: Before installing, please refer to DESICCANT USER GUIDE in the package to place
the desiccant in the camera to prevent moisture from condensing on the IS-IP200-IRB
glass cover.
2. Camera Cabling
Please follow the instructions below to complete IS-IP200-IRB connection.
2.1 Connect Power
Please refer to SECTION:CONNECTORS. Alternatively, connect the Ethernet cable to the
camera’s PoE port and plug the other end of the cable into a PoE switch.
NOTE: If using PoE, make sure Power Sourcing Equipment (PSE) is in use in the
network.
2.2 Connect Ethernet Cable
Use of Category 5 Ethernet cable is recommended for network connection; to have best
transmission quality, cable length shall not exceed 100 meters. Connect one end of the
Ethernet cable to the RJ-45 connector of the IS-IP200-IRB, and the other end of the cable to the
network switch or PC.
NOTE: In some cases, you may need use an Ethernet crossover cable when connecting
the camera directly to the PC.
Check the status of the link indicator and activity indicator LEDs; if the LEDs are unlit, please
check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
2.3 Connect Alarm I/O
The camera equips one alarm input and one relay output for alarm application.
Please refer to the label on the alarm terminal block and connect the alarm wiring accordingly.
3. Installation
Please read the instructions provided in this chapter thoroughly before installing the IS-IP200-
IRB.
3.1 Ceiling / Wall Mounting
The IS-IP200-IRB can be installed directly on a wall or ceiling with the integrated 2-axis
adjustable Bracket Mount. Please note that the wall or ceiling must have enough strength to
support the camera.
Follow the steps below to install the IS-IP200-IRB:
Step 1. Unpack the IS-IP200-IRB package and take out the Camera.
Step 2. Connect the power / Ethernet / alarm / audio wires from ceiling or wall to the
corresponding connectors of the camera’s All-in-one Cable.
Step 3. Attach the camera to the ceiling
/ wall with the supplied self-
tapping screws.
Step 4. Loosen the screw indicated in
the figure, and adjust the
camera to a desired position,
and tighten the screw to secure
the camera.
Step 5. Use the supplied hex wrench
and cross screwdriver to loosen
the hex bolt / screw on the side
of the bracket mount and the
camera housing to adjust the
position of the IS-IP200-IRB.
Autres manuels pour IS-IP200-IRB
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Sentry360 Caméra de sécurité
Sentry360
Sentry360 FS-IP5000 Manuel utilisateur
Sentry360
Sentry360 IS-IP200-IRB Manuel utilisateur
Sentry360
Sentry360 IS-DM200 Manuel utilisateur
Sentry360
Sentry360 FS-IP12360-V Manuel utilisateur
Sentry360
Sentry360 FS-IP10K Manuel utilisateur
Sentry360
Sentry360 FS-IP8180 Manuel utilisateur
Sentry360
Sentry360 FS-IP6360-V Manuel utilisateur
Sentry360
Sentry360 FS-IP3000-M Manuel utilisateur
Sentry360
Sentry360 IS-DM830 Manuel utilisateur
Sentry360
Sentry360 IS-IP10K Manuel utilisateur
Sentry360
Sentry360 IS-BL800 Manuel utilisateur
Sentry360
Sentry360 FS-IP12180 Manuel utilisateur
Sentry360
Sentry360 IS-IP200-DN Manuel utilisateur
Sentry360
Sentry360 IS-IP14K Manuel utilisateur
Sentry360
Sentry360 IS-IP200-IRB Manuel utilisateur
Sentry360
Sentry360 IS-DM520 Manuel utilisateur
Sentry360
Sentry360 FS-IP5000-M Manuel utilisateur
Sentry360
Sentry360 FS-IP12180-V Manuel utilisateur
Sentry360
Sentry360 FS-IP14K-DN Manuel utilisateur
Sentry360
Sentry360 IS-DM260 Manuel utilisateur
