Sensio Luce Manuel utilisateur

LUCE - SLS LED

PLINTH LIGHT KIT

CODE: 06.1110.0110

Components

Important safety information

Safety instructions

Tools required

INSTALLATION

INSTRUCTIONS

IMPORTANT: please read these instructions before commencing installation and retain for future reference.

Please read these instructions carefully before attempting to install

this product. It is advisable to keep these instructions in a safe place

for further reference.

We recommend that you consult a qualiﬁed electrician. All

electrical installations must be carried out in accordance with

current IEE wiring regulations (BS7671).

These products must not be modiﬁed, if any modiﬁcations are

made, it may invalidate the warranty and may render the product

unsafe. These LED lights operate low voltage (12V).

Do not wire the individual LED light ﬁttings directly to the mains.

This product is for indoor use only.

• If in doubt installation must be carried out by a qualiﬁed

electrician.

• Install on smooth ﬂat surface(s) only.

• Do not exceed or stretch the cable length of each LED wire.

• This product is IP44 Rated

•Each fitting runs at 0.18W. The driver in this pack has a maximum

allowance of 4W.

1. Before commencing installation or maintenance, isolate the main

electrical supply for the appropriate circuit at the fuse board.

2. This product is only suitable for connecting to a 240V 50Hz supply.

The light should be mounted onto a secure surface.

Never exceed the total output of the LED driver (4W).

4. Suitable for furniture lighting.

5. When the lamp expires the ﬁtting must be replaced.

6. Class III safety extra low voltage (SELV)

7. A maximum of 22 fittings can be run from the driver in this pack.

Waste Electrical & Electronic Equipment (WEEE)

The Symbol on the product, or on the document accompanying the product, the crossed out

wheelie bin symbol, indicated that this product may not be treated as household waste.

Instead it shall be handed over to the applicable collection point for the recycling of electrical and

electronic waste.

44mm Screw Bit Power Drill1x 13A Plug Driver and LED

cable connector

4 x LUCE LED Lights 1 x Fitting Instructions

Installation instructions

Maintenance & Care

• Ensure that the power is disconnected prior to cleaning.

• To keep the ﬁnish of this product, wipe over with soft cloth periodically.

• Do not use harsh chemical solvents, it may dis-colour or damage the ﬁnish.

Unit 7 Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY

www.sensio.co.uk

Technical drawings for illustration purposes only, Sensio has the right to change any information

without prior notice. Make sure you check all hole cut outs before work commences.

LUCE - SLS LED PLINTH LIGHT KIT

CODE: 06.1110.0110

These ﬁttings simply daisy chain

together, each have a length of

pre-wired cable containing a plug on

the end, allowing each ﬁtting to be

co-joined with another ﬁtting.

The plug on the last ﬁtting will then

simply be connected to the plug wired

onto the end of the transformer cable.

Allowing the pre-wired ﬁttings to be

connected straight to a plug socket.

We recommend that you consult a

qualiﬁed electrician.

Maximum 22 x 0.18W LED ﬁttings

per LED 4W driver.

Cut out four 44mm holes in the

plinth at your required locations.

Feed the wire from the ﬁrst ﬁtting through the cut out

hole, peel off the two self adhesive pads on the back of

each ﬁtting then simply slot into place.

In turn connect each ﬁtting to the previous,

via the connection plugs on the end of each

ﬁtting.

The plug on the end of the last

ﬁtting will then connect to the

transformer, which is pre-wired

ready to plug straight to a plug

socket or extension cable.

Table des matières

Autres manuels Sensio Équipement d'éclairage

Sensio

Sensio Torino SE17232C0 Manuel utilisateur

Sensio

Sensio Verso SE16092N0 Manuel utilisateur

Sensio

Sensio Gamma SE183720 Manuel utilisateur

Sensio

Sensio Expanse Pro SE14192P0 Manuel utilisateur

Sensio

Sensio SE14092N0 Manuel utilisateur

Sensio

Sensio Treos SE11290N0 Manuel utilisateur

Sensio

Sensio Fino SE981320 Manuel utilisateur

Sensio

Sensio Titan IP44 Manuel utilisateur

Sensio

Sensio Strata Manuel utilisateur

Sensio

Sensio SE10755P0 Manuel utilisateur

Sensio

Sensio SE9080HD Manuel utilisateur

Sensio

Sensio Connex Triotone SE100490 Manuel utilisateur

Sensio

Sensio CONNEX SE100190 Manuel utilisateur

Sensio

Sensio Titan Plus Manuel utilisateur

Sensio

Sensio Horizon Pro SE11095P0 Manuel utilisateur

Sensio

Sensio SE184720 Manuel utilisateur

Sensio

Sensio Blaze SE182720 Manuel utilisateur

Sensio

Sensio Adapt SE186790 Manuel utilisateur

Sensio

Sensio Neutron SE10455C0 Manuel utilisateur

Sensio

Sensio Magnum Manuel utilisateur

Sensio

Sensio SE30555C0 Manuel utilisateur

Sensio

Sensio Beam SE982120 Manuel utilisateur

Sensio

Sensio Ark TrioTone SE11192T0 Manuel utilisateur

Sensio

Sensio SE10615C0 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur