Selkirk DSP Manuel utilisateur

RM19896-1

SELKIRK CANADA CORPORASELKIRK CANADA CORPORA

SELKIRK CANADA CORPORATIONTION

TIONTION

TION

P.O. Box 526, Depot 1

Hamilton,OntarioL8L7X6

905-662-6600

Fax905-263-9308

1-800-263-9308

TollFreeFax1-866-835-9624

www.selkirkcanada.com

19/03/04

SELKIRK LLCSELKIRK LLC

SELKIRK LLC

14801QuorumDrive

Dallas, Texas, USA 75240

972-560-2000

Fax972-560-2428

1-800-992-VENT(8368)

TollFreeFax1-877-393-4145

www.selkirkinc.com

®USC

PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING YOUR

INSTALLATION. FAILURE TO INSTALL THIS SYSTEM IN ACCORDANCE WITH

THESE INSTRUCTIONS WILL VOID THE CONDITIONS OF CERTIFICATION AND

THE MANUFACTURERS WARRANTY . KEEP THESE INSTRUCTIONS IN A SAFE

PLACE FOR FUTURE USE.

Tested to

*UL103HT & ULC-S641

A MAJOR CAUSE OF CHIMNEY CONNECTOR RELATED FIRES

IS FAILURE TO MAINTAIN REQUIRED CLEARANCES

(AIR SPACES) TO COMBUSTIBLE MATERIALS.

IT IS OF THE UTMOST IMPORTANCE THAT THIS

DOUBLE WALL CHIMNEY CONNECTOR BE INSTALLED

ONLY IN ACCORDANCE WITH THESE INSTRUCTIONS

FACTORY BUILT CHIMNEY CONNECTOR

LISTED

INSTALLATION

INSTRUCTIONS

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

TYPES OF APPLIANCES

Your Chimney Connector is intended to connect a gas, liquid, or

solid fuel appliance normally producing flue gases of 650°C/

1200°F (Canada), 540°C/1000°F (US - to the Temperature

requirements of UL103HT) or less to a factory built or masonry

chimney.

This Chimney Connector must not be enclosed or pass through

attics, closets, floors, walls or ceilings, and must not be used in

place of an insulated chimney section.

The Minimum Clearance to combustibles (i.e.. walls, ceilings,

etc.) is 6" (152mm).

For mobile home installations follow the installation

instructions for the mobile home appliance and use the

chimney connector clearance required by the appliance.

PRE-INSTALLATIONGUIDELINES

Plan the installation of your appliance and chimney connector in

such a way that your chimney connector run is as short and

straight as possible.

By having too long and/or multiple bend installations you can

reduce system draft which can affect the operation, and/or

performance of your appliance and/or chimney system.

Ensure that you obtain any necessary building permits, and that

your installation will conform with all federal and municipal

building code requirements. Before commencing installation:

Use this chimney connector only with an appliance listed by a

recognized testing authority such as Intertek Testing Services

(Warnock Hersey), CSA, Underwriters Laboratories Inc.,

or Underwriters Laboratories of Canada.

The maximum recommended length of Double Wall Stove

Pipe should not exceed 20ft. Reduce this maximum limit

by 10% for every 90° bend or 5% for every 45° bend.

Provide sufficient slope in the horizontal run of the chimney

connector (20mm per meter, 1/4" per foot) to enable any

condensed liquid or creosote to run back toward the appliance.

Ensure that the horizontal chimney connector is securely

supported from the structure by means of metal or other non-

combustible supports at intervals not exceeding 1m (3ft).

All joints between sections of the chimney connector must be

secured with three sheet metal (supplied) screws per joints.

The black surface of the chimney connector may be touched up

with a high temperature flat black stove paint.

If you are upgrading from a single wall stove pipe to the

Double Wall Stove Pipe Chimney Connector, have your

chimney inspected by a certified wood technician or a certified

chimney sweep.

PARTS CHECK LIST

SECURING OFTHE DOUBLE WALL

STOVE PIPE (DSP)

The following is to assist you in connecting the Double Wall

Stove Pipe (DSP) to the Chimney system. There are two (2)

connecting methods. A Finishing Band (packaged with all

Telescopic and Adjustable Lengths) or it may be purchased

separately (DSP-FB). The second method is with the Universal

Chimney Adaptor.

Both methods can also be utilised on other chimney systems.

In all installations, all single wall parts of the chimney pipe

adaptor must be fully covered by the Finishing Band or the

Universal Chimney Adaptor. In order to accomplish this some

trimming may be required.

INSTALLATIONPROCEDURES

Install the appliance and chimney system according to the

installation instructions provided with them, ensuring that the

required clearances are maintained

CONTACTLOCALBUILDINGORFIREOFFICIALS

ABOUTRESTRICTIONSAND INSTALLATION

INSPECTIONINYOURAREA.

Inner Pipe with

crimped end

pointing down

into the

appliance flue

outlet

Outer Black

Pipe with

crimped end

pointing up

toward the

chimney

Theorientationof allchimneyconnectorcomponents must

be with the crimped end (outer black pipe) pointing up,

towardsthechimney(seediagrambelow).

ATTENTION!

To complete a proper Double Wall Stove Pipe installation, the

following parts may be required:

• Telescopic Length

• Adjustable Length

• Universal Chimney Adapt

• 6" Pipe Length

• 12" Pipe Length

• 24" Pipe Length

• 36" Pipe Length

• 45oElbow

• 90oElbow

• Tee Section

• Masonry Adapter

• Damper Kit

• Finishing Band

• Stove Adapter

• Oval to Round Adaptor

• Flush Stove Adaptor

* Denotes size of product 6"(152mm), 7"(178mm), 8"(203mm)

DSP*TL

DSP*AL-1

DSP*CA

DSP*P6-1

DSP*P12-1

DSP*P24-1

DSP*P36-1

DSP*E4-1

DSP*E9-1

DSP*TE-1

DSP*MA

DSP*DK-1

DSP-FB

DSP*SA-1

DSP8OTR

DSP*FSA-1

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

SUPERVENT

SELKIRK

STEP 2 : Pre-drill 3 evenly-spaced holes into the Universal Chimney

Adapter (CA) with a 3/32 metal drill bit. See Figure 2. These holes must

also pierce the Stove Pipe Adapter (ASE) and the Smoke Pipe Adaptor.

STEP 3 : Secure in place with 3 metal screws #6 X 1". NOTE:

Tigthen screws until head meets metal casing. Do not over tightnen

the screws such that the outer casing becomes deformed.

UNIVERSAL

CHIMNEY

ADAPTER

(CA)

SUPERVENT'S

CHIMNEY PIPE

ADAPTER

(ASE)

Pre-drill 3 holes evenly-spaced

with a metal bit. See Step 2.

ChimneySection

FIGURE 1

Beveled edge

FIGURE 2

SELKIRK'S

CHIMNEY PIPE

ADAPTER

Pre-drill 3 holes evenly-spaced

with a metal bit. See Step 2.

UNIVERSAL

CHIMNEY

ADAPTER

(CA)

Supervent/Superpro

Assembly

Telescopic

Length

Figure 2A

Supervent/Superpro Assembly

Step 4. On a Through-The-Wall Installation with a 90 degree

elbow, it may be necessary to cut the Chimney Pipe Adaptor

and /or the Finishing Band to the required width to be covered.

Ensure that the Finishing Band overlaps the crimped end of

the DSP and overlaps the bead snug to the beveled edge or to

the Basecap as per Figure 2A & 2B.

Step 1.Position theTelescopic Length to the appropriate location over

the Chimney Pipe Adaptor. Ensure that it’s final position will be cov-

ered by the Finishing Band which is only 3”wide. The Finishing Band

must overlap the crimped end of the DSP and the bead to the beveled

edge of the Chimney Pipe Adaptor or to the Basecap (see Figure 1A).

Step 2. Pre-drill 3 evenly spaced holes into the crimped end of

the DSP through the Chimney Pipe Adaptor with a 3/32 metal

drill bit. Secure in place with 3 #8 X 1/2” stainless steel sheet

metal screws (not supplied).

Step 3. Wrap the Finishing Band over the crimped end of the

DSP and the Chimney Pipe Adaptor. Ensure it is over the bead

and snug to the beveled edge or to the Basecap. Mark this

position using the 2 pre-punched holes in the Finishing Band as

a template. Pre-drill with a 3/32 metal drill bit and secure the

Finishing Band with the 2 supplied black sheet metal screws.

Figure 1B shows when it is all assembled.

Finishing

Band

Chimney

Pipe Adaptor

Selkirk Assembly

Finishing Band

to overlap the

Bead and snug

to the Beveled

edge of the

Chimney Pipe

Adaptor

Position

Finishing

Band over

the crimped

end

Position

Finishing

Band over

the crimped

end

Telescopic Length

Position

Finishing

Band snug to

the Basecap

Figure 1A

Figure 1B

Finishing Band Installed

Chimney

Pipe Adaptor

Finishing

Band

90 Degree Elbow

Finishing

Band

90 Degree Elbow

Supervent/Superpro

Assembly

Telescopic

Length

Figure 2B

Selkirk’s Assembly

Selkirk Assembly

INSTALLATION OF FINISHING BAND

(FB)

STEP 1 : SlidetheUniversal ChimneyAdapter (CA)overthe maleend

of either the Stove Pipe Adapter (ASE) or the Smoke Pipe Adaptor all

the way until snug to bead and beveled edge. See Figure 1.

INSTALLATIONOFTHEUNIVERSAL

CHIMNEYADAPTER

Basecap

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

"6"

INSTALLATION TYPE#3(SeeFigureC)

This installation is used when a factory built chimney system is

located through the wall behind the appliance.

1. Place the Telescopic Length on top of the appliance with the

male (crimped) end up, and the female end over the appliance

outlet collar . Attach it with the 3 metal screws supplied. If the

collar of your appliance is too large for the Telescopic Length to

fit over you will have to use a stove adapter on top of the stove

before installing the Telescopic Length.

2. Install a 90oElbow to the Chimney Adapter and then to the

chimney connector coming through the wall, ensuring that the

elbow is properly aligned for connection to the Telescopic Length.

If the clearances of the appliance requires a greater horizontal

distance than that provided by the 90oElbow, install the required

connector length totheelbow first,and then install your Chimney

Adapter and secure the pieces together with the 3 metal screws

provided. If using the Finishing Band see "Installation of Finishing

Band".

INSTALLATION TYPE#2(SeeFigureB)

This installation utilizing a Tee Section, is used when the chimney

systemisoffsetfromtheappliance, eithertomaintainproperclearances

for the appliance or for incorporating a cleanout in the chimney system.

1. Place the Telescopic Length on top of the appliance with the male

(crimped) end up, and the female end over the appliance outlet collar

and attach it with the 3 metal screws supplied. If the collar of your

appliance is too large for the Telescopic Length to fit over you will have

to use a stove adapter on top of the stove before installing the

Telescopic Length.

2. Install the 90oElbow to the Tee Section branch and the Univer-

Insulated Chimney Section

Chimney Pipe Adapter

3 Metal Screws

Telescopic Length

90oElbow

Tee

Section

Appliance

Finishing Band or Universal Chimney Adapter

Ceiling Support

FIGURE -B-

sal Chimney Adaptor to the top of the Tee. Secure the sections

together with the 3 metal screws supplied ensuring that the elbow

is properly aligned for connection to the Telescopic Length. See

"Installation of Finishing Band" if used.

3. Install the Elbow/Tee/Chimney Adapter assembly to the top of

the Telescopic Section and secure the sections together with the 3

metal screws supplied.

4. ExtendtheTelescopicLength untiltheChimneyAdapter slidesover

the chimney connector and secure the upper and lower sections of the

Telescopic Length in place with the 3 metal screws supplied. If the

installation requires more length than provided by the telescopic length

then install the fixed length(s) on the appliance and the telescopic

length next to the 90oElbow. All connections are to be fastened

together with the 3 metal screws provided with each length.

3 Metal Screws

Telescopic Length

3 Metal Screws

Chimney Support

ChimneySection

Appliance

FIGURE -A-

Chimney Pipe Adapter

Finishing Band or Universal Chimney Adapter

Insulated Chimney Length

3 Metal Screws

1. Place the Telescopic Length on top of the appliance with the male

(crimped) end up, and the female end over the appliance outlet collar.

Attach itwith the 3 metal screws supplied. If thecollar of your appliance

istoolargefor theTelescopicLengthtofitoveryouwillhavetouseastove

adapter on top of the stove before installing the Telescopic Length.

2. IfusinganUniversalChimney Adaptorplaceiton topof theTelescopic

Length and secure it in place with the 3 metal screws supplied. If using

the Finishing Band see "Installation of Finishing Band".

3. Extend the Telescopic Length until the Chimney Adapter slides over

the stove pipe adapter and secure the upper and lower sections of the

Telescopic Length in place with the 3 metal screws supplied. If the

installation requires more length than provided by the telescopic length

then install the fixed length(s) on the appliance and the telescopic length

next to the chimney. All connections are to be fastened together with the

3 metal screws provided with each length.

INSTALLATION TYPE#1(SeeFigureA)

This installation is used when the chimney system is located

immediately above the appliance.

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

"6"

INSTALLATIONTYPE#4(SeeFigureD)

This installation is the same as Installation Type #3 with the

exception that the Chimney connecter is run to an existing

Masonry Chimney instead of a Factory Built Chimney.

1. If your existing Masonry Chimney does not have a Chimney

Liner installed, it is required one be installed in order to make a

proper connection to the Double Wall Stove Pipe.

2. Once your Chimney liner is in place, make sure the opening in

the Chimney or liner is the correct size to accept the Masonry

Adapter. Slide the Masonry Adapter into the opening in the

chimney and into the branch of the Liner Tee until the collar of the

Adapter fits flush to the wall of the chimney. If Masonry Adapter

is too long and the collar does not fit flush to the wall, or it projects

too far into the Tee the Adapter should be trimmed for proper fit.

The Adapter should fit snug and not loose and there should be no

gaps where heat or products of combustion might escape. If the

adapter is loose fitting or gaps are present when it is installed they

should be filled with a suitable filler.

3. After installing the Masonry Adapter follow the instructions in

Installation Type #3.

FIGURE -D-

3 Metal Screws

3 Metal

Screws

Masonry

Adapter

3 Metal Screws

90oElbow

Appliance

Fixed Length Chimney

Liner

Masonry

Chimney

3 Metal Screws

Appliance

FIGURE -C-

Telescopic Length

Chimney Pipe Adapter

Finishing Band or

Universal Chimney Adapter

90oElbow

Telescopic Length

Insulated

Chimney

Sections

Insulated

Tee Section

WallThimble

12" Insulated

Section

Wall Support

Bracket

RULE FOR SAFE OPERATION AND MAINTENANCE

Do not use fuel materials corrosive to the chimney such as

driftwood, chemically treated wood or garbage or over fire your

solid fuel appliance. This can cause failure of the DSP Double

Wall Stove Pipe and will void any warranties.

When wood is burned slowly, it produces tar and other organic

vapors, which combine with expelled moisture to form creosote.

The creosote vapors condense in the relatively cool chimney flue

of a slow-burning fire. As a result, creosote residue accumulates

on the flue lining. When ignited, this creosote makes an extremely

hot fire.

Withanewinstallation,thechimneyshouldbeinspectedfrequently

(every 2 weeks if need be) to determine the rate of creosote

formation. When familiar with the appliance and chimney

characteristics, the chimney should be inspected at least once

every 2 months during the heating season to determine if a

creosote or soot build-up has occured.

If you see deposits more than 2mm (1/16") thick, clean all

connector pipe and chimney system mechanically (with a properly

sized plastic cleaning brush) to reduce the risk of chimney fire.

Contact a local professional chimney sweep for chimney cleaing

services and advice.

Do not expect chemical chimney cleaners to keep your chimney

clean. Their use does not negate the necessity of periodically

inspecting and cleaning your chimney.

KEEP YOUR CHIMNEY AND

CONNECTOR CLEAN!

3. Extend the Telescopic Length until it connects with the 90o

Elbow and secure the upper and lower sections of the Telescopic

Length in place with the 3 metal screws supplied. Fasten the

Telescopic Length and the 90oElbow together with the 3 metal

screws provided. If the installation requires more length than

provided by the telescopic length then install the fixed length(s) on

the appliance and the telescopic length next to the 90oElbow. All

connections are to be fastened together with the 3 metal screws

provided with each length.

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

LIMITED LIFETIME WARRANTY:

Selkirk Canada Corporation, ( “we”, “us”, “our”) warrants Chimney & Venting products * to be free from defects in material and workmanship

for as long as the original consumer owns the system. For products installed after January 1, 2000, for a period of Ten (10) years from original

installation,wewillprovidereplacement product with a similar or like quality of available product,freeofchargeexcludinganyinstallationcosts.

From the Eleventh (11) through Fifteenth (15) years we will provide replacement product to the original consumer at a cost of 75% off the

published Retail Price in effect on the date the claim is received excluding any installation costs. At expiration of the Fifteen (15) year term, we

willprovide replacement product to the originalconsumer at a cost of 50%off the published Retail Price ineffect on the date the claimisreceived

excluding any installation costs.

LIMITATIONS:

-Products must be installed for their intended purpose.

- Products must be connected to an appliance listed with an accredited testing laboratory.

WARNING: FAILURE TO INSTALL PRODUCTS ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS WILL VOID

ALL APPLICABLE WARRANTIES AND MAY RESULT IN FIRE, CARBON MONOXIDE POISONING OR DEATH. SEE

OUR PRODUCT INSTALLATION INSTRUCTIONS FOR COMPLETE INSTRUCTIONS.

WARRANTY COVERAGE:

All lengths, tees and elbows, and components are applicable to warranty coverage.

THIS LIMITED WARRANTY DOES NOT COVER:

(a) any non-stainless base tee unit mounted or connected to an Insulated Chimney system;

(b) costs (labor or otherwise **) associated with either removing a previously installed product, installing a replacement

product, transportation or return of a product, or transportation of replacement product;

(d) damage resulting from failure to reasonably clean, care for or maintain products in accordance with our installation instructions/

recommendations;

(e) damage (to products, appliances or structure) based on or resulting from improper installation or repair, misuse or abuse (including, but not

limited to, excessive or improper operating condition), or alteration or adjustment other than in conformity with our installation instructions and

specifications, whether performed by a contractor, service company, technician, or yourself;

(f) any products that have been moved from their original installation site.

(g) damage caused by burning driftwood, garbage, or any other prohibitive material has been burned in the appliance served by the chimney

(h) damage that results from accidents such as fire, flood, high winds, “acts of God”, or any other contingency beyond our control.

** Due to the wide variance in installation practices and other conditions beyond our control, we do not guarantee

or in any way warrant the installation of Chimney and Venting products.

CLAIM PROCEDURE:

If you believe that a product is defective, notify us in writing at the following location:

LIMITED LIFETIME WARRANTY

SELKIRK CANADA CORPORASELKIRK CANADA CORPORA

SELKIRK CANADA CORPORATIONTION

TIONTION

TION

P.O. Box 526, Depot 1,Hamilton,Ontario,CANADA,L8L7X6

ATTN: WARRANTY CLAIMS DEPARTMENT

Fax:(905)662-5352

Notification should include a description of the product, model and serial number (if applicable) and a description of the product defect. Upon

receipt of a written claim under this limited warranty and evidence of the date of purchase or installation, at our option and in our sole discretion,

we will provide replacement product with similar or like quality of available product excluding any installation costs. We reserve the right to

inspect or investigate any warranty claims prior to determining whether to provide replacement product. If, as determined by us that repair or

replacementof the product is not commercially practicableorcannot be completed in a timelymanner, we may refundtheproratedpurchaseprice

paid for the product upon verification by providing a copy of your invoice or receipt of bill of sale.

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

keep in safe place for future reference

MODEL OF CHIMNEY: _______________________________

TYPE OF APPLIANCE: ______________________________

INSTALLATION DATE: ____________________________

DESCRIPTION OF INSTALLATION (Chimney and Chimney Connector configuration) ______________

________________________________________________________________________________________

PURCHASED FROM:

DEALER NAME: _________________________________________________

Address: _________________________________________________

City: _________________________________________________

Province/State: _________________________________________________

INSTALLED BY:

TECHNICIAN NAME: _____________________________________________

Address: _____________________________________________

City: _____________________________________________

Province/State: _____________________________________________

Please register your Chimney with the Manufacturer.

Name: _________________________________________________________________________

Address: _________________________________________________________________________

City: _________________________________________________________________________

Province/State: _________________________________ Postal/Zip: ___________________________

Model: _________________________________ Installation Date: ______________________

Dealer Name: __________________________

INSTALLATION INFORMATION

PRODUCT REGISTRATION

NorthlineExpress.com

http://www.northlineexpress.com

Toll-Free 1-866-667-8454

Table des matières

Autres manuels Selkirk Accessoires de cheminée

Selkirk

Selkirk SUPERVENT SC Instructions d'utilisation

Selkirk

Selkirk DIRECT-TEMP 4DT-CCK Manuel utilisateur

Selkirk

Selkirk SUPERVENT 2100 Instructions d'utilisation

Manuels Accessoires de cheminée populaires d'autres marques

Valor

Valor L2 1700K Manuel utilisateur

Exodraft

Exodraft Xzense Manuel utilisateur

Whalen

Whalen Ruso MNFP62BF23-6 Manuel utilisateur

Lopi

Lopi Hearthview 864 Manuel utilisateur

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuel utilisateur

EdilKamin

EdilKamin SERBATOIO 250 Guide de démarrage rapide

Bronpi

Bronpi KIT-1 Manuel utilisateur

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuel utilisateur

Travis Industries

Travis Industries 33 DVI Manuel utilisateur

Superior

Superior ASD3628-TI Manuel utilisateur

pleasant hearth

pleasant hearth OFP28WG Manuel utilisateur

IHP

IHP Astria Series Manuel utilisateur

Firegear

Firegear FG-H-2110SS Manuel utilisateur

Nibe

Nibe Contura C i31 Manuel utilisateur

kozy heat

kozy heat KZK-052 Manuel utilisateur

SimpliFire

SimpliFire SF-WM36 Manuel utilisateur

Bluegrass Living

Bluegrass Living BC18NR Guide de démarrage rapide

pleasant hearth

pleasant hearth IRIS SCROLL Manuel utilisateur