Sekonic C-500 Manuel utilisateur

C-500/C-500R

PRODIGICOLOR

C-500/C-500R

Operating Manual



C-500/C-500R

1. Parts Designation

①Light Senso

②Liquid Crystal Display (LCD)

③POWER button

(ON/OFF switch)

④PRESET button

(“A” in radio sub-channel setting)

⑤MODE button

(“C” in radio sub-channel setting)

⑥MENU button ⑪Flash Synchro terminal

⑦MEASURE/OK button

⑧Jog Wheel

⑨SET K button

(“B” in radio sub-channel setting)

⑩DISPLA

button

(“D” in radio sub-channel setting)

⑫⊿

BACK button

⑬Battery Cover Latch

⑭Battery Compartment Cove

⑮Battery Compartmen

⑰Strap eyelet

⑯Tripod Socket

C-500/C-500R

2. Explanation of the Liquid Crystal Display

C-500/C-500R

①Measuring Mode Icons

Ambient

Auto-Reset Cordless Flash

Cord Flash

Wireless Flash Radio Triggering Mode

②Battery Power Indicator

(Displayed) Battery power level is good

(Displayed) Battery power level is low. Have a spare battery ready

(Blinking) Replace battery immediately

③Flash Measurement Range Icons

※(Displayed)Auto-Reset Cordless Flash Mode or Cord Flash Mode

(Displayed) H Range Select

(Displayed) L Range Select

④DIGITAL/FILM Mode Icons

(Displayed) DIGITAL Mode Select

(Displayed) FILM Mode Select

⑤Selected Color Temperature Display

(Displayed) Set-up Color temperature

①

②

③

④⑤

⑪

⑥

⑦

⑩

⑨

⑧

C-500/C-500R

⑥Shutter Speed Display

※(Displayed)Auto-Reset Cordless Flash Mode or Cord Flash Mode

“S” Appears when shutter speed is in full seconds

Example: 1s is displayed for shutter speed 1 second. 60 is displayed for shutter speed

1 / 60 seconds.

⑦Preset Color / White Balance Display and Contrast Icons

(Displayed) Selected Preset Function (Selected Preset No. 1~19)

(Displayed) Used Monitoring facility

⑧Dot Matrix Display for Preset Name, Menu and Illuminance

A menu name is displayed during menu selection.

A Preset name is displayed at the time of a Preset setup.

The unit of illumination is displayed only when Ix or FC is set up with the Illumi. Sub menu of a

custom-made setup.

⑨LB, Measured Color Temperature and Illuminance Display

LB index, LB filter, and a color temperature are displayed by display mode.

A simple illumination display is displayed only when Ix or FC is set up with the Illumi. Sub menu of

the custom-made setup.

In the error besides the display range and the measurement range, u, Under or o, and Over are

displayed.

u, Under Appears when below display range

“u, Under” Blinks when under measured below measurement range

o, Over Appears when above display range

“o, Over” Blinks when over measured above measurement range

⑩CC Display

CC index and CC filter are displayed by display mode.

⑪Radio triggering channel and Quad-triggering Zone Display

(Displayed) Wireless Flash Radio Triggering Mode

The main channel which chose 1~16 channels is displayed.

The main channel (17~32) which chose 17~32 channels, and a sub-channel (A~D) are displayed.

Auto Electro-Luminescent Display (EL)

In low light (160lx or less), a green backlight will automatically illuminate the entire LCD.

The LCD will not be automatically illuminated during measuring, in Cordless Flash mode or

Wireless flash radio triggering mode.

The Electro-luminescent backlight will automatically turn off 20 seconds after last operation.

C-500/C-500R

FCC & IC compliance information:

Warning: Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant

To Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction, may

cause harmful interference to radio communication.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determine

by turning the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules and also with RSS-210 of Industry Canada.

Operation is subject to the following two condition: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC ID Number: PFK-500-01 IC ID Number: 3916A-500001

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sekonic Instrument de mesure

Sekonic

Sekonic SPECTROMASTER C-7000 Guide de l'utilisateur

Sekonic

Sekonic Auto-Leader L-38 Manuel utilisateur

Sekonic

Sekonic SPECTROMASTER C-800 Guide de l'utilisateur

Sekonic

Sekonic L-398A Studio Deluxe III Manuel utilisateur

Sekonic

Sekonic TWINMATE L-208 Manuel utilisateur

Sekonic

Sekonic Litemaster Pro L-478D Guide de l'utilisateur

Sekonic

Sekonic Studio Deluxe L-28 C2 Manuel utilisateur

Sekonic

Sekonic LITEMASTER PRO Manuel utilisateur

Sekonic

Sekonic SPEEDMASTER L-858D Guide de l'utilisateur

Sekonic

Sekonic AUTO LUMI L-158 Manuel utilisateur

Sekonic

Sekonic L-98 Manuel utilisateur

Sekonic

Sekonic DIGITALMASTER L-758DR Manuel utilisateur

Sekonic

Sekonic HANDY LUMI Manuel utilisateur

Sekonic

Sekonic i-346 Manuel utilisateur

Sekonic

Sekonic SPEEDMASTER L-858D Manuel utilisateur

Sekonic

Sekonic Litemaster Pro L-478DR Manuel utilisateur

Sekonic

Sekonic DUAL MASTER L-558 Manuel utilisateur

Sekonic

Sekonic MULTIMASTER L-408 Manuel utilisateur

Sekonic

Sekonic FLASH MASTER L-358 Manuel utilisateur

Sekonic

Sekonic STUDIO DELUXE? L-398A Guide de l'utilisateur

Sekonic

Sekonic FLASHMATE L-308X Manuel utilisateur

Sekonic

Sekonic SPEEDMASTER L-858D Guide de l'utilisateur

Sekonic

Sekonic L-478D Series Guide de l'utilisateur

Sekonic

Sekonic L-608 CINE Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur