Seen IRIS-i Manuel utilisateur

INSTALLATION GUIDE

SEEN IRIS-i Camera

This guide is intended for anyone installing SEEN IRIS-i cameras on SEEN IRIS-860 sensors. For information on how to

create a SEEN Insight account and activate camera subscriptions, refer to the SEEN Insight User Guide.

www.seensafety.com | we’ve Got Your Back

Contents

Before you start 3

Overview 3

Requirements 3

Installation 4

Antenna 5

LED indication 5

Troubleshooting 5

Internal memory 6

Maintenance 6

Warranty 7

Specifications 7

Seen Safety Limited

Email: support@seensafety.com

Call Toll free: +1 888 858 4648

www.seensafety.com

Important

Install and test the IRIS 860 sensor before

installing the IRIS-i camera.

Maximum 80V DC power supply.

Voltages exceeding 80V may result in

damage to the camera and will not be

covered by the warranty.

This installation and set-up guide has been

prepared with all due care and attention,

however, Seen Safety Limited cannot be

held responsible for any errors or omissions

in this guide or any consequences thereof.

In the box

• IRIS-i camera

• 300mm M12 connector cable

• Weather shield

• Mounting bracket

• Antenna + 600mm cable

• Antenna mounting bracket

• 4 x M6 x 12mm hex head screw

• 2 x M6 x 16mm hex head screw

• 2 x M6 Nylock nut

Before You Start

• Fully install and test the IRIS 860 sensor before attaching

the IRIS-i camera.

• Read these instructions in full before starting.

• IRIS-i cameras do not record sound.

• Cameras must be activated in SEEN Insight before they can

upload data.

Note. Detection events are recorded and saved in the

camera memory even if the IRIS-i is not connected to the

network. These detections will be uploaded once the device

connects to the network. See page 6.

Overview

The IRIS-i camera is designed to be attached to an IRIS 860

sensor. Detection information is automatically uploaded by

IRIS-i to SEEN Insight (insight.seensafety.com).

When powered, IRIS-i cameras automatically connect to the

mobile data network via an embedded roaming SIM card.

IRIS-i cameras upload the following information about each

detection event:

• A still image

• The time, date, duration, and closest distance

• Trace path through the detection zone

• Video (optional upload).

Requirements

• 3G / 4G mobile coverage.

• An installed IRIS 860 sensor.

• A SEEN Insight account.

• SEEN Insight account data credit.

IRIS 860 sensor and IRIS-i camera

IRIS 860 sensor and IRIS-i camera (back)

Installation

Fully install and test the IRIS 860 sensor before attaching the

IRIS-i camera.

The IRIS-i camera can be attached to either side of an IRIS 860

sensor. Configure Step-1 according to which side of the sensor

the camera will be mounted on.

Step 1

2 x M6 x 12mm + nylock nut. 10Nm

Step 3

2 x M6 x 12mm. 10Nm

(M12 plug sockets at bottom)

Step 5

Connect sensor and camera

using the 300mm M12

connector cable

Step 4

Transfer sensor power

cable to camera

Step 2

Replace the two sensor bracket screws with

the 2 M6 x 16mm screws supplied. 10Nm

Power

Note the sensor accessory

socket is not used.

Finger tight only.

Do not use tools.

Finger tight only.

Do not use tools.

Antenna Connection

1. The antenna should be mounted upright with minimal

shading from metallic surfaces. (Before attaching the

antenna check that the antenna cable can reach back to the

camera.)

2. Connect the antenna cable to the centre antenna socket.

Finger tighten only, do not use tools.

LED Indication

BLUE LED

A solid blue LED indicates that the IRIS-i is powered and can

communicate with the IRIS 860 sensor.

GREEN LED

A solid green LED indicates that the IRIS-i has connected to

the mobile data network.

FLASHING LED

A flashing LED (either blue or green) indicates that the IRIS-i

camera cannot communicate with the IRIS 860 sensor.

Troubleshooting

IRIS-i LED is not blue

• Check the cables are correctly installed (refer to page 4)

and the camera is receiving power from the machine.

IRIS-i LED does not turn green

• Even in areas with strong mobile coverage the IRIS-i may

take several minutes to first connect to the network.

Connection is indicated by a green LED.

• In areas with weak mobile coverage, connection may take up

to 15 minutes.

• If the LED does not turn green, try moving the machine to

an area with stronger mobile coverage.

• Check the antenna cable is correctly fastened.

• Try repositioning the antenna to get a clearer signal.

• Restart the IRIS-i. It must be powered o for more than 10

seconds to fully shut down.

IRIS-860 sensor LED is not green

• Check the sensor is correctly connected to the camera and

that the camera is receiving suicient power.

Antenna socket

5 pin M12 power socket

(Connected to the

machine power supply)

8 pin M12 sensor socket

(Connected to the

IRIS 860 sensor)

Antenna cable

Antenna

IMPORTANT

The antenna must be mounted at least

10cm away from the IRIS 860 sensor.

DO NOT attach the antenna to either the

sensor bracket or the camera bracket

because it may interfere with the sensor

operation.

10cm+

Finger tight only.

Do not use tools.

Internal Memory

The IRIS-i camera’s internal memory stores detection data

until it is uploaded to SEEN Insight, or it is over-written by new

data.

Detection event data

Information about each detection (data and still-image) is

immediately uploaded to SEEN Insight when the camera is

online. If the network connection is lost, the camera can store

up to 1,000 detection event records which will be uploaded

next time the camera connects.

Detection event video clips

The camera can store approximately 12,0001detection event

videos before they start to be over-written. Detection event

videos that are still in the camera’s memory can be uploaded

to SEEN Insight. Once the camera’s memory buer is full, the

oldest videos will start to be over-written by new detection

event videos. Sound is not recorded.

Rolling video buer

A 6 hour rolling video buer is saved to the camera’s memory.

This video buer is continuously over-written by new material

when the camera is powered on. Sound is not recorded.

Emergency procedure

In the event of an emergency the camera should be removed

from the machine and not powered on to ensure data is not

over-written or lost. Contact support@seensafety.com

*The exact number will vary depending on the duration of each

event.

Maintenance

IRIS-i cameras have no user-serviceable parts. If needed, the

window should be cleaned with water and a non-abrasive

cloth. Avoid all solvents, degreasers, petroleum or alcohol

cleaning products.

The camera is rated IP67.

Do not use high pressure water jets to clean.

1 The exact number will vary depending on the duration of

each event.

Specifications

Input power DC12-80V. Electrical 2.0A Standards FCC Part 15

PTCRB

EN 301489 EMC emissions and immunity

Direction signal input DC 3.5-100V electrical 1mA Ingress protection IP67. Protected from dust ingress and water

ingress at 1 metre submersion for 30 minutes.

Avoid high pressure water jets

Power consumption 24W max with attached sensor plus

sensor accessory

Enclosure ASA injection moulded plastic

Camera field of view 70 degrees horizontal x 55 degrees

vertical

Window Hard coated PMMA with oleophobic and anti-

reflective coatings.

Maintenance Clean with water and a soft clean

cloth. Avoid all solvents, degreasers,

petroleum or alcohol cleaning products

Operating

temperature -20 to +60 degrees C ambient

Connectors M12 5-pin (power supply)

M12 8-pin (to sensor)

Dual SMA antenna connectors (RF

connector in centre)

Dimensions 110mm H x 64mm W x 66mm D

Weight 0.26kg

IRIS-i camera label

Warranty

IRIS-i cameras have been designed for reliable long-term

use on industrial vehicles in indoor or outdoor applications.

The camera is covered by a 1 year replacement warranty on

materials and workmanship. The warranty excludes general

wear and tear, physical damage caused by direct impact

to the camera, over-tightening or misalignment of the M12

connectors, damage to the camera window, damage caused by

high-pressure water jets, damage caused by chemical cleaners

(including alcohol, benzene, thinners, and degreasers),

or damage caused by over-voltage to the power supply.

IRIS-i cameras have no user serviceable parts. Opening the

enclosure will void the warranty.

SCN0023

A0001234

Example camera serial number

SCN0023A0001234

Power socket (M12 5-pin)

Pin Name Description Direction Max.

input

voltage

Min.

input

voltage

Input

high

voltage

Input

low

voltage

Output

high

voltage

Output

low

voltage

Conditions Notes

1 Vin + Supply positive Input 92v 10.8v - - - - - 24W maximum power draw

2 Vin – Supply negative

(ground)

- - - - - - - - System / chassis ground

3 System

status

High when

system operating

Output - - - - 5.5v max.

4.5v min.

2.7K Ohm load

to ground

PNP output

4 Detection High when target

detected

Output - - - - 5.5V max

4.5V min.

2.7K Ohm load

to ground

PNP output

5 Direction

signal in

Input Input 100v 0v 3.5v min. 1v max. - - - Input current is less than

1.0 mA

Sensor socket (M12 8-pin)

Pin Name Description Direction Max.

input

voltage

Min.

input

voltage

Input

high

voltage

Input

low

voltage

Output

high

voltage

Output

low

voltage

Conditions Notes

1 Vout + Supply output to

IRIS 860 sensor

Output - - - - 16v - Limits IRIS 860 supply

voltage to 16V

2 Vout - Supply negative

(ground)

- - - - - - - - System / chassis ground

3 Reserved

4 Reserved

5 Direction Direction signal

output to sensor

Output - - - - 16V max

6.8V min.

- 10K ohm load

to ground

PNP output

6 Trigger in Camera trigger

input

Input 30V 0V 3.5V

min.

0.7V

max

High impedance external

trigger input for the camera

Product specifications are subject to change without notice to improve reliability, function, design or otherwise.

5 pin power socket

8 pin sensor socket

Seen Safety Limited

Email: support@seensafety.com

Call Toll free: +1 888 858 4648

www.seensafety.com

IMPORTANT. SEEN IRIS 860 sensors can provide collision warning assistance to the operator but do not replace the need for

proper operator training and best practice safe operating procedure. While IRIS 860 sensors can alert the machine operator

to a potential collision, the operator is always fully responsible for the safe operation of the equipment. IRIS 860 sensors do

not comply with the regulatory standards required for devices which are intended to directly control vehicle or machine safety

functions. Using the sensor accessory port to control a vehicle or machine function is entirely at your own risk. Detection can

never be guaranteed.

trademarks of Seen Safety Limited.

Autres manuels pour IRIS-i

Table des matières

Autres manuels Seen Appareil photo numérique

Seen

Seen IRIS-i Manuel utilisateur

Manuels Appareil photo numérique populaires d'autres marques

Mercury

Mercury 350K Manuel utilisateur

Pentax

Pentax Optio LS 465 Manuel utilisateur

Sanyo

Sanyo VPC-S1085 Manuel utilisateur

GE SMART A1255 Manuel utilisateur

Point Grey

Point Grey Gazelle Manuel utilisateur

Nikon

Nikon COOLPIX A Manuel utilisateur

Pentax

Pentax P-5 Manuel utilisateur

BlazeVideo

BlazeVideo A280 Manuel utilisateur

Sony

Sony MCA-20 Manuel utilisateur

Sony

Sony Alpha DSLR-A290 Manuel utilisateur

ATIK Cameras

ATIK Cameras One Manuel utilisateur

CohuHD Costar

CohuHD Costar 3930 Series Manuel utilisateur

Leica

Leica M10-R Manuel utilisateur

FujiFilm

FujiFilm FinePix A700 Manuel utilisateur

Lorex

Lorex LNZ81P25 Series Manuel utilisateur

GE J1470S Manuel utilisateur

Sony

Sony A6700 Guide de l'utilisateur

Canon

Canon EOS ELAN7 Manuel utilisateur